• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.7
• /
• pp.81-90
• /
• 2009

Due to environmental issues, the development of low energy consumption products has become one of the main topics in the home appliance industry. The energy consumption of a refrigerator depends on the efficiency of its compressor as well as on the refrigerator cycle design, such as the capacity modulation. In this study, a dual capacity, i.e., two-step capacity modulation (TCM), reciprocating compressor is developed. In a TCM compressor, capacity modulation is achieved by changing the dead volume in the cylinder. Instead of a concentric sleeve, an eccentric sleeve, a key, and a spring are used to change the dead volume for the clockwise and counterclockwise rotation of a motor. When the compressor changes its operating mode from full capacity to partial capacity or in opposite direction, the key may collide with the eccentric sleeve. The structural reliability and mode change reliability were confirmed by analysis and experiment.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.3
• /
• pp.76-82
• /
• 2000

본 논문에서는 환경에 구속 받는 유연 매니퓨레이터의 힘/위치에 대하여 논하고자 한다. 일반적으로, 유연 매니퓨레이터의 모델링 방법은 분포 정수 모델과 집중 정수 모델로 분류할 수 있다. 전자인 분포 정수 모델을 이용해서는 평면 1 링크, 2 링크를 대상으로 한 위치/힘 제어는 가능하나, 운동 방정식의 복잡성으로 인하여 실시간에서 다 링크 다 관절 유연 매니퓨레이터의 힘/위치를 제어하기는 어렵게 여겨져 왔다. 본 논문에서는 집중 정수 모델링 방법인 집중 스프링 질량 모델(Lumped Spring Mass Model)을 이용하여 환경에 구속받는 유연 매니퓨레이터의 운동 방정식을 산출했다 이 모델을 실험기인 유연 매니퓨레이터 ADAM(Aerospace Dual Arm Manipulators)에 적용하여 실시간 위치/힘 제어 실험을 행하였으며, MATLAB를 이용하여 해석했다. 또한, ADAMS$^{TM}$ FEM를 이용하여 분포 정수 모델을 도출하여, 해석하였으며, 이 결과와 집중 정수 모델을 이용한 MATLAB 해석의 결과, 그리고 실험 결과를 비교 분석하여 본 논문에서 제안한 구속받는 유연 매니퓨레이터의 집중 정수 모델 타당성을 입증시켰다.

• KSTLE International Journal
• /
• v.2 no.1
• /
• pp.75-79
• /
• 2001

This paper is a report on the parametric study of the friction characteristics on the direct acting type OHC valve train system. The numerical simulation was performed by using the IV-TAP. Dynamic analysis by using the lumped mass method was previously performed to define the acting load. The friction characteristics were analyzed by using the partial asperity contact model. The effects of operating conditions and major design parameters on the total driving torque were investigated. From the analytical prediction, it is found that valve spring stillness, surface roughness, and base circle radius are the main factors to reduce the frictional loss on the valve train system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.8
• /
• pp.21-29
• /
• 2013

The functional behaviors of human standing postural control were investigated when they were exposed to long-term horizontal vibration in the sagittal plane. For complexity of human postural control, a useful alternative method that has been based on a black-box approach was taken; that is, where the feedback mechanism was lumped into a single element. A motor-driven support platform was designed as a source of vibration. The AC Servo-controlled motors produced continuous anterior/posterior (AP) motion. The data were analyzed both in the time and frequency domain. The cross-correlation and coherency functions were estimated. Subjects behaved as a non-rigid pendulum with a mass and a spring throughout the whole period of the platform motion, as consistent with the plan chosen for this study.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.564-568
• /
• 2006

Smooth picture module is operated by vibration to tilt the light from the DMD (digital micro mirror device) of DLP projection TV, which makes the screen of the TV smoother and DMD chip cost lower. To satisfy the vibration characteristics of smooth picture module, it is designed by optimizing moment of inertia, spring constant and damping coefficient, using structural and fluid dynamic simulation that showed a good agreement with experimental data. To reduce the material cost and moment of inertia, engineering plastic is used and the reliability is estimated. A VCM (voice coil motor) type actuator for smooth picture has to satisfy performance requirements such as higher driving force, lower power consumption, and lower cost. The initial design and optimization for VCM was performed using FE analysis. It allowed us to optimize the design of magnetic circuit of the proposed actuator to obtain higher force while maintaining a lower cost.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.1-6
• /
• 1991

This paper is concerned with the design of a robust tracking controller using a state observer on a robotic manipulator under the disturbance. The controller is designed to follow a step or ramp reference input without steady state error in the presence of a disturbance and a system parameter variation. In most cases, since all the state vectors are not measured, unmeasurable state vectors must be estimated or reconstructed. A reduced order observer is proposed to estimate unmeasurable state vectors of the non-linear system. Some problems are caused by the Coulomb friction, the disturbance, and the spring effect of a link between the drive motor and the manipulator arm. The state variables, directly measured and estimated by the reduced order observer, are fed back to the controller. When the robot system exhibits the 'limit cycle, the feedback gains initially obtained by optimal control theory are changed. As a result, the limit cycle is eliminated by the new controller gains,

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.962-967
• /
• 1991

A counter balance valve is used as one part of hydraulic motor brake system. The function of this valve is to protect over-run or free falling of inertia load. But occasionally the brake system with counter balance valve makes some undesirable problems such as pressure surges or vibrations. In this study, for the purpose of easy estimation about dynamic characteristics of hydraulic system including counter balance valve, precise formulation describing fluid dynamics and valve dynamics under various boundary conditions were made. Dynamic characteristics were analysed by numerical integration using Runge-Kutta method, because the equations in this circuit with counter balance valve contain various nonlinear terms. Propriety of this analysis method is verified by experiment. For the purpose of obtaining fundamental data for preventing instability, this study experimented the effects of the spool taper, spring constant, cylindrical choke. And we developed double acting brake system integrated counter balance valve.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.418-421
• /
• 2001

Press brake is used as bending and forming sheet metal in vehicle and many kind of industry. This paper deals with development of NC press brake based on high precision positioning device and software, which can be operated on personal computer. In this system, positioning device is used for controlling bending angle and operated by the developed software, which is database from material property, width and thickness of material. This study will make distribution in development of computer aided press brake.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.494-497
• /
• 2003

A rotating device driven by an Inchworm motor was designed and fabricated to be used as an angie standard system. 1. PZT was adopted as a driving source, while the movement of PZT was guided by the leaf spring employing the elastic transformation of metals. 2. The device could rotate in a 360-degree arc. continuously Performance test of the device showed about 0.02 sec. of the minimum revolution angle and 1/15 rpm of the maimum revolution speed. 3. To improve its performance requires further studies on realizing a shifting device with faster response time, on increasing the output current (capacity) of the power amplifier used to drive PZT, on the dynamic motion of clamping. and on determining the optimum clamping condition

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.10
• /
• pp.170-179
• /
• 2004

A vibration model of powder transfer equipment is developed by the lumped parameter method. A Powder transfer equipment does surging motion, bouncing motion and pitching motion. Motion equation becomes decoupling and removed vibration exciting source about pitching motion, and therefore designers presented the optimum design plan to be able to do adjustment with motion trajectory of powder transfer equipment. That is, way for design to be able to do motion trajectory of powder transfer equipment through change of design element as installation position and direction of motor, driving speed, mass unbalance, stiffness coefficient and installation position of support coil spring is presented. The design results, powder transfer equipment were able to know that fatigue destruction does not occur, and the reason is because maximum stress working on a basket structure is more very than fatigue strength small.