• Journal of Advanced Marine Engineering and Technology
• /
• 제8권1호
• /
• pp.64-71
• /
• 1984

In this paper, the fundemental equation on the Trans-vector control of 3.phi. Induction motor drive and the new equivalent circuit to be adapted for this equation, have been obtained, and control drives system to be coincide with this equation is made. Therefore, it has been obtained that control scheme can always be used motor drive. 3.phi. Induction motor drive has been got the dynamic behavior the same as that of DC motor drive. The drive dynamic response is very rapid because of Trans-vector control on the I_1$ (primary current) and .${\omega}_1$ (frequency of primary current) of the Induation mechine. This paper indicates that a practicality of the drive control system and the rationalty of the theory have been identified with the experimental results. The effect of parameter variations on the drive dynamic response can be evaluated from these results.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권6호
• /
• pp.450-456
• /
• 2000

In this paper, we proposed a novel control method which uses the internal impedance angles as a control parameter to drive traveling wave type ultrasonic motor. An impedance characteristic of the ultrasonic motor is obtained by analysis of the equivalent circuits including the external inductor used to generate the coupled resonance. The phase angle of internal impedance to achieve optimal control performance is derived. For the tracking of impedance angle, an information of phase difference is obtained from the applied voltage and current. The high speed phase difference detector is designed to monitor the phases of ultrasonic motor. The effectiveness of the proposed control scheme is clarified by experiments.

• 전기학회논문지P
• /
• 제51권3호
• /
• pp.111-119
• /
• 2002

This paper proposes a speed control system based on a fuzzy logic approach, integrated with a simple and effective adaptive algorithms. And this paper attempts to provide a thorough comparative insight into the behavior of induction motor drive with PI, direct and improved fuzzy speed controller. A indirect vector controlled induction motor is simulated under varying operating condition. The validity of the comparative results is confirmed by simulation results for induction motor drive system.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제3B권1호
• /
• pp.32-36
• /
• 2003

The three-phase canned induction motor, which consists of a stator and rotor with a seal can, is used for the main coolant pump (MCP) of the System-integrated Modular Advanced Reactor (SMART). The thermal characteristics of the can must be estimated exactly, since the eddy current loss of the can is a dominant parameter in design. Besides the insulation of the motor winding is compared of Teflon, glass fiber, and air, so it is not an easy task to analyze. A FEM thermal analysis was per-formed by using the thermal properties of complex insulation which were obtained by comparing the results of finite element thermal analysis and those of the experiment. As a result, it is shown that the characteristics of prototype canned induction motor have a good agreement with the results of FEM.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1395-1401
• /
• 2010

A paradigm shift in driving system of transportation vehicle from engine to electric motor is required as the problems on air pollution and drain of petroleum resource are on the rize. Moreover while it is possible to control the motor with variable frequency driver, the application of motor in various kinds of vehicles is spread rapidly. In the paper, the effective design method of IPMSM for EV and HEV by using equivalent magnetic circuit and finite element method (FEM) is suggested. First of all, load conditions of the application are calculated. And basic design process of IPMSM is proposed with two design point. Finally, in order to verify the proposed design process, it was compared with the basic design parameter and the FEM analysis results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.296-298
• /
• 1995

This paper proposes a new filter topology that suppresses the high voltage gradient(dv/dt) in ac motor terminals. The high voltage gradient(dv/dt) causes over voltages on the motor windings, the degradation or motor insulation, and the bearing failure. Moreover surge voltage with high voltage gradient(dv/dt) in the PWM inverter red drive system where long line cables are required causes more serious problem to the motor. Thus, the most advisable method is attaching output filter to the inverter output terminals. The conventional output filters have several problems such as bulky size, difficulty or parameter tuning. The proposed filter can be relatively smaller than the conventional filters. By the proposed filter, the shaping or PWM waveform can considerably suppress high dv/dt in motor feeding cable from the inverter. The effectiveness or the proposed filter is compared with that or the conventional one and is verified by the computer simulation.

• 전기학회논문지
• /
• 제59권10호
• /
• pp.1797-1802
• /
• 2010

This paper proposes a new fuzzy speed controller based on the Takagi-Sugeno fuzzy method to achieve a robust speed control of a permanent magnet synchronous motor(PMSM). The proposed controller requires the information of the load torque, so the second-order load torque observer is used to estimate it. The LMI condition is derived for the existence of the proposed fuzzy speed controller, and the LMI parameterization to calculate the gain matrices of the controller is provided. It is proven that the augmented control system including the fuzzy speed controller and the load torque observer is exponentially stable. To evaluate the performance of the proposed fuzzy speed controller, the simulation and experimental results are presented under motor parameter and load torque variations. Finally, it is clearly verified that the proposed control method can be used to accurately control the speed of a permanent magnet synchronous motor.

• 조명전기설비학회논문지
• /
• 제23권11호
• /
• pp.69-75
• /
• 2009

In this paper, a self-tuning regulator for a speed control of a permanent magnet type stepping motor is proposed. The self-tuning theory provides a nonlinear modeling of a stepping motor drive system and can provide the controller with information regarding the reference variation and parameter variation of the stepping motor through the on-line estimation. The proposed self-tuning regulator organize the positive feedback loop and IP(Integral-Proportional) type. Therefore, the proposed self-tuning regulator has a robust control capabilities during dynamic operation. The availability of the proposed controller is verified through experimental results.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.405-410
• /
• 1999

Hydraulic pipeline between servo valve and actuator affect the dynamic characteristics of electrohydraulic servo systems in serveral ways. This paper deal with the speed control of oil hydraulic gear motor using electrohydraulic servo valve. The frequency and transient response of electrohydraulic servo valve coupled to a gear motor is anlayzed. In particular, the effect of short and long hydraulic pipelines between servo valve and gear motor is investigated. The dynamic characteristics of the speed control systems of gear motor with short pipeline is first described via frequency response experiments with small signal linearized analysis. Loner pipeline is applied distributed parameter pipeline model with consideration of frequency dependent viscous friction.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.289-292
• /
• 2002

A sensorless control of a PM synchronous motor under the parameter variation is presented. The rotor position is estimated by using the d-axis and q-axis current errors between the real system and motor model of the estimator. The stator resistance is measured at low speeds when the motor changes its rotating direction. The gains in the position estimator are also adapted according to the motor speeds.