• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.9
• /
• pp.24-30
• /
• 2009

This paper is proposed by fuzzy-based MPPT control of photovoltaic to drive induction motor. Design and prototype implement of a fuzzy logic(FL) controller for maximum power extraction from a stand-alon photovoltaic. Error and the change of error between maximum power and real power are used by input of fuzzy controller. Moreover, it output changing of voltage from control constant. The validity of this paper is proved by comparing maximum power point tracking and performance of motor drive through comparison fuzzy and PI of tradition method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.3
• /
• pp.239-246
• /
• 2003

Brushless D.C. Motor is widely used for industrial application because of high efficiency and high power density. Especially, in home appliance, BLDCM is very useful due to high control performance and low acoustic noise. In this paper, BLDCM and its controller are designed and developed for tread mill application. With the restricted stator structure, permanent magnet rotor is designed for manufacturing and cost effectiveness using CAD and FEM analysis. A ferrite magnetic material is used as a rotor magnet for the cost and temperature advantages. For a stable operation of tread mill, over current and temperature can be detected and protected. The designed BLDCM and its controller was verified by the experimental results.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.337-341
• /
• 2002

본 논문은 원자력 발전소의 안전에 있어 매우 큰 비중을 차지하는 모터 구동밸브(Motor-operated valve : MOV)의 성능진단에 직접 센서를 장착하지 않고 전기신호만을 이용하여 성능진단의 가능성을 보이기 위한 것이다. 모터 토크를 계산하기 위한 두 가지 방법으로서 D-Q frame 변환 방법과 Air-Gap 토크 식을 제시하였고, 계산된 두 토크 값은 정확하게 일치하였다. 부하를 변동하면서 토크미터로 측정된 토크 갑과는 1%의 오차범위 내에서 일치함을 확인했다. 따라서 두 토크 식은 모터구동 밸브의 성능진단을 위한 식으로 사용해도 좋다는 결론을 얻어낼 수 있었다. 계산된 토크를 주파수 분석함으로서 부하의 변동에 따라서 슬립 및 모터속도 주파수가 변화됨을 알 수 있었다. 즉 주파수 분석을 통해 MOV의 모터 및 구동기 부분의 성능 저하 감시에 유용한 단서를 제공해 줄 것이다. 결과적으로, MOV에서 전기신호의 분석은 시스템의 전기 및 기계적인 성능 저하 감시에 이용될 수 있을 것으로 기대된다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.6
• /
• pp.608-615
• /
• 1999

In this paper, the compliance control method was propoSL'Cl and the phase-difference operating principle of an u ultrasonic motor described. The compliance control can he implementtcD with spring/damper properties of the r musculo-skeletal system of the actual limb in controlling its net configuration and movement. The proposed p phase-difference driving scheme is verifitcD through the computer simulation. Also, $textsc{k}$rformance of the proposed c control method of a two-link direct-drive manipulator are examinLD by the experimental results with resptc'Ct to s spring/ damper properties.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.88-95
• /
• 2008

This paper proposes a fast fault detection algorithm under open-circuit fault of a switch for a brushless DC(BLDC) motor drive system. This proposed method is configured without the additional devices for fault detection and identification. The fault detection and identification are achieved by a simple algorithm using the operating characteristic of the BLDC motor. After the fault identification, the drive system is reconfigured for continuous operation. This system is reconfigured by four-switch topology connecting a faulty leg to the middle point of DC-link bidirectional switches. This proposed method can also be embedded into existing BLDC motor drive systems as a subroutine without excessive computational effort. The feasibility of a the proposed fault detection algorithm is validated in simulation and experiment.

• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.650-654
• /
• 2007

Induction motors are widely used as a source of driving force in electric vehicles and pulse width modulation (PWM) inverters are applied to their operation. The issue is that insulation of inverter-fed induction motors (IFMs) are more stressed than in line-powered motors by transient voltages. This paper dealt with experimental results on transient voltage produced by the PWM operation of an induction motor. The peak and the dv/dt of transient voltage depending on the length of power feeding cable and operating frequency were investigated. In the experiment, transient voltages up to 3.3PU of the rated-inverter voltage were recorded for the cable length of 50m. As the cable length is increased, the peak voltage appeared at the motor terminals increases. This phenomenon can be explained by the reflection and the transmission of travelling wave. Consequently, special care for the cable length between the motor and the inverter should be taken in the use of IFM to ensure the full life of insulation system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.75-84
• /
• 2005

Since an unexpected fault of induction motor drive systems can cause serious troubles in many industrial applications, which the technique is required to diagnose faults of a voltage-fed PWM inverter for induction motor drives. The considered fault types are rectifier diodes, switching devices and input terminals with open-circuit faults, and the signal for diagnosis is derived from motor currents. The magnitude of dq-current trajectory is used for the feature extraction of a fault and PCA LDA are applied to diagnose. Also, we show results with respect to the execution time because of the possibility to use that a diagnosis software is embedded in the controllers of medium and small size induction motors drive for real-time diagnosis. After we performed various simulations for the fault diagnosis of the inverter, the usefulness of proposed algerian was verified.

• Journal of the Korean Institute of Gas
• /
• v.26 no.2
• /
• pp.21-26
• /
• 2022

Since the four-wheel drive transmits the driving force to all four wheels, the traction with the road surface increases, thereby increasing the driving force. However, it has the disadvantage of lowering fuel efficiency. Therefore, four-wheel drive is commonly used as a method of converting to optional four-wheel drive when necessary while driving in two-wheel drive. This selective four-wheel drive converts the driving force by mechanically changing the electric signal sent by the driver in the transfer case. In this study, in order to mechanically change the electrical signal, a reducer is applied to the motor to increase the torque to perform the function. Therefore, in this study, a reduction mechanism applicable to the motor inside the transfer case applied to convert the drive is derived, and the reduction ratio applying the planetary gear type is optimized accordingly. And based on the derived reduction ratio, two sets of planetary gears using a ring gear in common were applied to develop a planetary gear tooth type in which the input shaft and output shaft are decelerated in the same phase. Optimization design was carried out.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.1
• /
• pp.150-158
• /
• 1999

A driving system of a dynamic FOG compass with a stabilized platform is described. A stepping motor adopted as a driving motor is required to maintain a stable operation with constant speed and low oscillation for the proper operation of the FOG compass itself. The previous stabilization scheme operated on frequency-modulated supply is modified to include fuzzy control algorithm. The proposed scheme has advantages, particularly in the size, weight and flexibility of the driving system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.519-526
• /
• 2003

A singl-phase power factor corrected converter for switched reluctance motor hive is presented to achieve a sinusoidal and new unity power factor input currents. Because it combines a power factor corrected converter and a conventional asymmetric SRM driver into one power stage, the configuration has a simple structure resulted in low cost. A prototype to drive 6/6 poles SRM employing a parking magnet Is designed to evaluate the proposed topology. The characteristics and operational mode will be discussed in depth, and the validity of proposed driver will be verified through the experimental results.