• Journal of Ocean Engineering and Technology
• /
• v.35 no.4
• /
• pp.266-272
• /
• 2021

Mooring systems are among the most important elements employed to control the motion of floating offshore structures on the sea. Considering the use of polymer material, a new method is proposed to address the creep characteristics rather than the method of using a tension load cell for measuring the tension of the mooring line. This study uses a synthetic mooring rope made from a polymer material, which usually consists of three parts: center, eye, and splice, and which makes a joint for two successive ropes. We integrate the optical sensor into the synthetic mooring ropes to measure the rope tension. The different structure of the mooring line in the longitudinal direction can be used to measure the loads with the entire mooring configuration in series, which can be defined as SMART (Smart Mooring and Riser Truncation) mooring. To determine the characteristics of the basic SMART mooring, a SMART mooring with a diameter of 3 mm made of three different polymer materials is observed to change the wavelength that responds as the length changes. By performing the longitudinal tension experiment using three different SMART moorings, it was confirmed that there were linear wavelength changes in the response characteristics of the 3-mm-diameter SMART moorings. A 54-mm-diameter SMART mooring is produced to measure the response of longitudinal tension on the center, eye, and splice of the mooring, and a longitudinal tension of 100 t in step-by-step applied for the Maintained Test and Fatigue Cycle Test is conducted. By performing a longitudinal tension experiment, wavelength changes were detected in the center, eye, and splice position of the SMART moorings. The results obtained from each part of the installed sensors indicated a different strain measurement depending on the position of the SMART moorings. The variation of the strain measurement with the position was more than twice the result of the difference measurement, while the applied external load increased step-by-step. It appears that there is a correlation with an externally generated longitudinal tensional force depending on the cross-sectional area of each part of the SMART mooring.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.3
• /
• pp.161-168
• /
• 2016

This paper presents a methodology through which the time series of the dynamic response of mooring line tension can be predicted without relying on a time-consuming nonlinear time-domain analysis. The mooring line tension for the target short-term sea states was predicted using a Hammerstein-Wiener model, a popular system identification scheme, based upon the pre-calculated motion-tension time history data for some selected short-term sea states that do not overlap with the targeted ones. The obtained mooring line tension was further processed, and a fatigue damage comparison was made between the predicted and calculated values. The results showed that the predicted time series of the mooring line tension matched the calculated one fairly well. Thus, it is expected that the methodology may be employed to enhance the efficiency of mooring line tension analysis.

• Journal of Ocean Engineering and Technology
• /
• v.36 no.3
• /
• pp.153-160
• /
• 2022

Moored floating platforms have great potential in ocean engineering applications because a mooring system is necessary to keep the platform in station, which is directly related to the operational efficiency and safety of the platform. This paper briefly introduces the technical and operational details of an optical sensor for measuring the tension of mooring lines of a moored platform in waves. In order to check the performance of optical sensors, an experiment with a moored floating platform in waves is carried out in the wave tank at Changwon National University. The experiment is performed in regular waves and irregular waves with a semi-submersible and triangle platform. The performance of the optical sensor is confirmed by comparing the results of the tension of the mooring lines by the optical sensor and tension gauges. The maximum tension of the mooring lines is estimated to investigate the mooring dynamics due to the effect of the wave direction and wavelength in the regular waves. The significant value of the tension of mooring lines in various wave directions is estimated in the case of irregular waves. The results show that the optical sensor is effective in measuring the tension of the mooring lines.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.514-514
• /
• 2017

Floating breakwaters were treated as solid bodies without any perforation in previous studies. In this study, however, a floating breakwater is perforated to allow the partial absorption of the energy produced by incident waves and an air chamber is placed in the upper part to control the breakwater draft. A series of laboratory experiments for a floating breakwater installed with a mooring system are carried out. In general, a mooring system can be classified by the number of mooring points, the shape of the mooring lines, and the degree of line tension. In this study, a four-point mooring is employed since it is relatively easier to analyze the measured results. Furthermore, both the tension-leg and the catenary mooring systems have been adopted to compare the performance of the system. In laboratory experiments, the hydraulic characteristics of a floating breakwater were obtained and analyzed in detail. Also, a hydraulic model test was carried out on variable changes by changing the mooring angle and thickness of perforated wall. A hydraulic model was designed to produce wave energy by generating a vortex with the existing reflection method. Analysis on wave changes was conducted and the flow field around the floating breakwater and draft area, which have elastic behavior, was collected using the PIV system. From the test results the strong vortex was identified in the draft area of the perforated both-sides-type floating breakwater. Also, the wave control performance of the floating breakwater was improved due to the vortex produced as the tension in the mooring line decreased.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.2
• /
• pp.99-105
• /
• 2019

Unlike typical a dynamic positioning (DP) system, a DP-assisted mooring system must determine a set point (SP) that can ensure a mooring tension safety range to prevent an excessive increase in mooring tension. In this paper, a new algorithm for determining the SP is suggested in order to reduce the tension on all the mooring lines. To determine the SP, a working area around the vessel is represented by a rectangular grid. Thus, the size of the grid area is limited considering the offset of a vessel with a mooring system. At each grid's nodes, the resultant tension from all the mooring lines is estimated using the time history of the tension and vessel's position. The results of static analyses for each grid position are used to estimate the global tension. Consequently, the SP is automatically selected as a position satisfying criterion for minimizing the total tension. In order to validate the suggested algorithm, a motion simulation with the control system in the time domain and a discussion of the results are presented.

• Journal of Wind Energy
• /
• v.14 no.2
• /
• pp.26-33
• /
• 2023

In this study, the global response characteristics of floater and mooring for floating offshore wind turbine with a detachable mooring system are performed. Global motion and structural response result extracted from the coupled motion analysis of 10MW DTU floating offshore wind turbine with detachable mooring system modeled by high-order boundary element model and finite element mesh, were used to study the characteristics of tension on mooring lines subjected to three different types of ocean loads. Breaking limit of mooring line characterized by wind, current and wave load has a major effect on the distribution of mooring tension found in time domain analysis. Based on the numerical results of coupled motion analysis, governing equation for calculating the motion response of a floater under ocean loads, and excitation force and surge motion and tension respectively are presented using excursion curve. It is found that the response of floater is reliable and accurate for calculating the tension distributions along the mooring lines under complex loadings. This means that the minimun breaking limit of mooring system satisfied a design criteria at ultimate ocean environmental loading condtions.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.1
• /
• pp.46-56
• /
• 2008

A numerical model analysis was performed to analyze the motion and mooring tension response of submersible fish cage systems in irregular waves and currents. Two systems were examined: a submersible cage mooring with a single, high tension mooring and the same system, but with an additional three point mooring. Using a Morison equation type model, simulations of the systems were conducted with the cage at the surface and submerged. Irregular waves(JONSWAP spectrum) with and without a co-linear current with a magnitude of 0.5m/s were simulated into the model as input parameters. Surge, heave and pitch dynamic calculations were made, along with tension responses in the mooring lines. Results were analyzed in both the time and frequency domains and linear transfer functions were calculated.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.3
• /
• pp.202-207
• /
• 2017

This paper presents the results of an experimental study on the motions and mooring characteristics of a floating vertical axis wind turbine system. Based on a comparison of regular wave experiment results, the motions of structures with different types of mooring are almost the same. Based on the tension response results of a regular wave experiment with a catenary mooring system, the mooring lines in front of the structure have a larger tension effect than the back of the structure by the drifted offset of the structure. The dynamic response spectrum of the structure in the irregular wave experiments showed no significant differences in response to differences in the mooring system. As a result of the comparison of the tension response spectra, the mooring lines have a larger value with a drifted offset for the structure, as shown in the previous regular wave experiment. The results of the dynamic response of the structure under irregular wave and wind conditions showed that the heave motion response is influenced by the coupled effect with the mooring lines of the surge and pitch motion due to the drifted offset and steady heeling. In addition, the mooring lines in front of the structure have a very large tension force compared to the mooring lines in back of the structure as a result of the drifted offset of the structure.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.3
• /
• pp.39-46
• /
• 2005

A series of forced oscillation tests on a model mooring chain was carried out to investigate dynamic tension characteristics. The model test was conducted at two different water depths to gather basic data for a 'truncated mooring test' and 'hybrid mooring test'. The truncated and hybrid mooring tests are important for overcoming the limitation of water depth that existed in previous model tests. The resultant tension RAO provides a good possibility of approximation of dynamic tension by equivalent weight adjustment for different water depths. Because the hybrid mooring test is an adequate combination of model test and simulation, an accurate simulation model for the mooring system is essential. The simulation results show good agreement with model test results.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.134-141
• /
• 2002

A series of forced oscillation test on model mooring chain was carried out to investigate dynamic tension characteristics. The model test was conducted at two different water depth to gather basic data for 'truncated mooring test' and 'hybrid mooring test'. The truncated and hybrid mooring test are highly recommended to overcome the limitation of water depth in model test recently. The resultant tension RAO gives good possibility of approximation of dynamic tension by equivalent weight adjustment for the ratio of water depth in different water depth. Because the hybrid mooring test is the adequate combination of model test and simulation, accurate simulation model on mooring system is essential. The simulation results show good agreement with model test results.