• Special Issue of the Society of Naval Architects of Korea
• /
• 2011.09a
• /
• pp.70-74
• /
• 2011

This paper describes the quay mooring analysis to verify the safety of a moored drillship in typhoon conditions. Mooring system consists of mooring equipments(deck bollards, shore bitts, mooring lines, fenders) to resist the extreme environmental condition. Wind force acting on the drillship is obtained from the wind tunnel test results. The strength of quay mooring system has been checked. The static mooring analysis shows that the designed mooring system satisfies the mooring design criteria. Vertical displacements of the drillship have been calculated considering the dynamic wave motions and static heelings due to the wind force acting on the ship. With the vertical displacements and the hull draft of drillship, the required water depth for quay mooring has been derived.

• Journal of Navigation and Port Research
• /
• v.34 no.5
• /
• pp.311-317
• /
• 2010

Mobile Harbor(MH) is a new paradigm for maritime transport system introduced in Korea, the target of which is to carry out ship-to-ship cargo operation rapidly and effectively even under a condition of sea state 3. A MH ship is moored alongside a large container vessel anchored at the defined anchorage and also equipped with gantry cranes for handling containers. The MH study concerned includes rapid container handling system, optimum design for floating structure, hybrid berthing & cargo operation system, design for cargo handling crane, etc. This paper is to deal with a conceptual design of a stabilized mooring system and mooring equipment under a condition of ship-to-ship mooring. In this connection, we suggest a positioning control winch system in order to control heave motions of the MH ship which is to add constant brakepower and stabilized function to an auto-tension winch and mooring equipment used currently in large container ships.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.7 no.4
• /
• pp.286-303
• /
• 2002

Korea Ocean Research and Development Institute (KORDI) has attempted moored current measurements since 1978. This note describes mooring types and failures of moorings deployed in coastal and continental shelf regions around Korea. Taut-wire U-type mooring lines and trawl-resistant bottom mounts have been mainly used in shallow seas. In order to avoid the failure of moorings in the shallow seas, it is needed to (1) design a proper mooring plan considering local mooring environments including fishing activities and (2) use adequate mooring equipments and parts considering mooring period, depth, and other factors that could affect the mooring unexpectedly.

• Journal of the Korean Institute of Navigation
• /
• v.24 no.5
• /
• pp.373-383
• /
• 2000

The ship’s safe mooring stability is a principles for the safe cargo handling works at the mooring berth. Today numerous standards, guidelines and recommendations concerning mooring practices, fittings and equipments exist throughout the worldwide maritime industries. In recently, the mooring facilities were constructed as dolphin types at the open sea area apart far from shoreside instead of enclosed coastline area in accordance with increasing ship’s size and for preventing environmental pollution. Therefore the exciting wave condition must be considered as a basic environmental criteria with the wind force and current force for all of the mooring ships at the sea berth facilities. In this study, this added wave force as one of the environmental external forces by using the theoretical formula was applied to the LNG ship in Pyeongtaeg harbor needed the special mooring stability of the sea berth. Through this research, it can be confirmed that wave force is the very important factor in the mooring force and the strength of wave force works much more in the full laden condition than in the lightship condition. And also the wave force changes to non-linear states according to the wave frequency and wave length. In addition, the maximum limit criteria of environmental force of prohibiting the entering ship on the berth and loading works controlled by the port authority concerned of Pyeongtaeg port fully satisfies the condition of the mooring limit force recommended by OCIMF that the safe permitted force of the mooring line have to be within 55 % of MBL.

• Ocean and Polar Research
• /
• v.28 no.2
• /
• pp.209-214
• /
• 2006

The East Sea Branch (ESB) of KORDI will be launched in 2008. She will take a role of monitoring the sea surface topography and temperature by satellites, short- and long-term sea levels by tide gauges, coastal currents and open-sea circulation by setting up coastal radars and mooring current-meters and acoustic equipments, as well as monitoring nearshore processes, coastal erosion and water pollution. A basic program of coastal zone management will help ocean-policy makers to set up right decisions based upon scientific background of the regional data in the East Sea. Networking among the neighboring countries around the sea will supply more useful information not only for experts but also for ordinary vacationers or fishermen. In order for this program to be successfully settled down during the next decade, it is necessary for a leader to have the right vision to attract more experts from global brain pools and to manage the ESB as a leading-edge observatory in the world. Details about this leading-edge operational program are introduced in the text.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.1
• /
• pp.65-73
• /
• 1997

The floating body discussed in this study is a 2-D rectangular floating unit supported by four vertical piles at its corners. Structures of this type are frequently seen as floating piers for the crafts in a small harbour. The movement in some modes of motion of such a flating body is fully or partially restrincted by the piles. The authors(Kim et al. 1994) carried out a series of model tests on its wave control function, its motion and the loads on piles. The experimental results showed that a certain degree of intial constriction force which clamps the floating unit in the horizontal direction can effectively reduce the body motion and wave energy without increasing mooring forces. This may be due to the friction forces occuring between the piles and the rollers installed in the mooring equipments on the floating unit. In this paper, we develop a numerical model for the prediction of wave transformation and floating body motions, where the friction force is idealized as the Coulomb friction and linearized into a damping force using the equivalent damping cofficient. This linearization is verified by comparing the results of motions between the linear and nonlinear analysis of the ezuations of motion. We further compare the caculation results by the linear model with the experimental results and discuss the effect of the friction force or the constriction force on body motions and wave energy dissipation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4447-4454
• /
• 2013

In October 2011, a commercialized 100kW class floating photovoltaic system positive plant was installed at Hapcheon dam a multi-purpose reservoir the first time ever in the nation. Floating photovoltaic system differs in water float, mooring device and underwater cable process from land photovoltaic system. As for land and building photovoltaic power generation equipments, many installation cases and skilled experiences are available, and thus installation is not difficult. However, commercial power generation floating photovoltaic system, which is attempted for the first time in the nation, requires to be designed and installed through a series of processes like technical review and verification of data by process in comparison with similar cases. The structure of floating photovoltaic system, an equipment for float photovoltaic module and other electrical equipment, is required to withstand weather environments like wind or typhoon etc and yet not affect water quality negatively, and for implementation of this system, construction efficiency and economy etc should be considered comprehensively. In this paper, the techniques of installing floating photovoltaic structure, mooring device, underwater cable, electrical equipment and remote monitoring control system are explained. The 100kW floating PV system is operating with 15% average capacity factor.

• Journal of Fisheries and Marine Sciences Education
• /
• v.24 no.6
• /
• pp.872-883
• /
• 2012

Generally the determination of turning basin for vessels of entering & sailing in the berth has been considered in the design standard of harbor construction rules of the port. In this regard, the turning basin has been determined by the max size of entering vessel of the berth/port. But the size of turning basin may considered the ship's maneuvering ability, operator's skillful power, mooring equipments of the berth, arrangement of the fairway and the environment condition of weather & seas around the designated port area. So this paper suggested the optimum size of turning basin after studying the harbour design rules of the advanced marine countries and using by maneuvering simulator for turning basin size and also evaluated the design standard of harbor construction rules and minimum size of turning basin against ship's length at the Gangjung civil/naval port of Jeju Island.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.10 no.2
• /
• pp.47-57
• /
• 2007

Real-time oceanographic information system was developed using platforms of aquaculture farms to examine causes of mass mortality of hatchery fishes, and to reduce the damage of mass mortality which has been occurred frequently off coast by abnormal change of ocean conditions. The system had the advantages of direct data distribution to fishermen at the farm and instant maintenance of equipments due to easy access to the farms and residents at the farms in comparison with offshore mooring buoy system. To avoid discontinued measurement of the system, repairs caused by malfunction of equipments, bimonthly preventive maintenances and daily monitoring of measured data were systematized. Confidence intervals calculated by a statistical method using accumulated data were applied to data management. Such activities could minimize discontinuance of measurement and keep information more trustful. In addition, the system has various ways of data distribution. Through homepage and e-mail in the internet, information was provided to public. Display units which were connected to equipments at the farm gave the measured data directly to fishermen, which guided them to run their farm scientifically. Finally large display unit was installed at a fish market and showed the measured data at the nearest station with tide and weather information. Proper region for aquaculture and wintering region were studied using temperature data obtained by the system in 2006. The system will contribute to reduce economic damage of coastal fishery and to understand coastal marine environment.