• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.7
• /
• pp.585-592
• /
• 2015

Effects of opening distance on liquid-gas spray of pintle injector were experimentally investigated under atmospheric condition by using water and air as simulants of propellants. Discharge coefficients($C_d$) and mass flow rates were calculated with various injection conditions; 0.1 bar - 1.0 bar for water pressures and 0.2 mm - 1.0 mm for the pintle opening distances. Spray angles were measured from the spray images that were obtained by a shadowgraphy method. When opening distance is 0.2 mm, liquid sheet is not formed properly and it show non-uniform spray. than it can result in combustion instability. it has a weak correlation between the momentum flux ratio and the spray angle, while it has a strong correlation between the momentum ratio and spray angle. Finally the spray angles reduced exponentially when the momentum ratio increased and the spray angles converged to about 40 degrees.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.168-172
• /
• 2003

The effects of injection conditions on the droplet sizes resulting from the disintegration of a liquid jet by a fast annular gas stream have been investigated using PDPA. The gas/liquid momentum ratio M = $\rho$$_{g}$ $U_{g}$$^2$/$\rho$$_1$ $U_1$$^2$ and Weber number We = $\rho$$_{g}$ $g^2$ $D_1$/$\sigma$ are selected as key parameters in atomization of shear coaxial spray from the fluid mechanics standpoint. It is revealed that SMD( $D_{32}$) varies inversely with gas/liquid momentum ratio(M), whereas Weber number(We) has little effect on the droplet sizes as gas velocities increase. It is found that gas/liquid momentum ratio is more dominant factor controlling the breakup and atomization process of shear coaxial spray. Finally, an empirical correlation between SMD and injection conditions(i.e. gas/liquid momentum ratio M and Weber number We) is proposed based on the experimental results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.905-911
• /
• 2017

Effects of injector position and momentum flux ratio on a vertical jet in a cross flow field were studied qualitatively and shown by using air and water. The experiment was carried out by fixing the momentum flux ratio and varying the position of the injector hole. Conversely, the injector hole position was fixed and the momentum flux ratio was varied. Image visualization was performed by a Shadowgraph technique using a high speed camera. The visualized images were compared for finding differences in spraying through Density Gradient Magnitude Image. It is observed that as the x/d of the apparatus increased the jet break up height decreases and the spray angle also decreases. When x/d is 0, the spray reaches the floor and ceiling at any momentum flux ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.5
• /
• pp.88-96
• /
• 2018

Effects of injector position and momentum flux ratio on a vertical jet in a cross-flow field are qualitatively studied and displayed using air and water. The position of the injector hole and the momentum flux ratio is changed and image visualization is performed using a shadowgraph technique and a high-speed camera. The visualized images are compared to find differences in spraying using density gradient magnitude image. It is observed that, as the x/d of the apparatus increases, the jet break-up height decreases. When x/d is 0, the spray reaches the bottom and ceiling at any momentum flux ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.27 no.1
• /
• pp.27-36
• /
• 2023

To understand the atomization performance in gas-liquid swirl-coaxial injector applied to a small rocket engine, a cold-flow test was performed by varying the design parameters and supply condition of propellants. As the swirl-chamber diameter and the angle of the convergent section, which are design parameters of injector increased, the spray performance of the injector improved by increasing the swirl strength. In addition, as the gas-liquid momentum-flux ratio increased, the gas flow separated some of the droplets from the liquid film, and a gas-droplet mixture core was formed in the center of the spray sheet.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.7
• /
• pp.675-682
• /
• 2013

To verify the effect of inner- and outer-stage gas jets, a shear coaxial injector was designed to analyze the axial velocity profile and breakup phenomenon with an increase in the measurement distance. When the measurement position was increased to Z/d=100, the axial flow showed a fully developed shape due to the momentum transfer, aerodynamic drag effect, and viscous mixing. An inner gas injection, which induces a higher momentum flux ratio near the nozzle, produces the greater shear force on atomization than an outer gas injection. Inner- and Outer-stage gas injection do not affect the mixing between the inner and outer gas flow below Z/d=5. The experiment results showed that the main effect of liquid jet breakup was governed by the gas jet of an inner stage. As the nozzle exit of the outer-stage was located far from the liquid column, shear force and turbulence breaking up of the liquid jets do not fully affect the liquid column. In the case of an inner-stage gas injection momentum flux ratio within 0.84, with the increase in the outer gas momentum flux ratio, the SMD decreases. However, at an inner-stage gas jet momentum flux ratio over 1.38, the SMD shows the similar distribution.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.267-274
• /
• 2009

Breakup and spray formation of pressure-swirl liquid jets injected into a low-speed convective-flow are experimentally investigated. Effects of the cross-flows on the macroscopic and microscopic spray parameters are optically measured in terms of jet Weber number and liquid-to-gas momentum ratio. The liquid stream undergoes Rayleigh jet breakup at lower jet Weber numbers and a liquid sheet isn't formed because of the weak radial velocity in the swirl jet. At higher jet Weber numbers, the macroscopic spray parameter is a very weak function of the momentum ratio but the effect of the convection on the microscopic spray parameter is significant through the secondary breakup with increasing in the liquid-to-gas momentum ratio. The convective-flow promotes bag/plume breakup and the spray formation, and its effect is more distinct at higher momentum ratio.

• Journal of ILASS-Korea
• /
• v.18 no.3
• /
• pp.140-145
• /
• 2013

Sub/supercritical spray experiments were conducted, and cryogenic nitrogen and gaseous argon were selected for simulants. liquid nitrogen and gaseous argon were injected in subcritical case, and supercritical nitrogen and near-critical gaseous argon were injected in near-critical/supercritical cases. shadowgraph method was used to visualize spray, and analyzed about the breakup length. The breakup length was measured from numbers of Instantaneous shadowgraph Images from each case, and they were compared with momentum flux ratios and density ratios. It was observed that the relation between breakup length and momentum flux ratio was fitted into former experiment results. and the reasonable constant was suggested about the relation between breakup length and density ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.5
• /
• pp.1-9
• /
• 2012

The gas jet from a coaxial porous injector for two-phase flows is discharged from the porous surface, which encloses the center liquid jet, and the gas and liquid jet interact with each other physically. The wall injected gas jet transfers the radial momentum effectively while the radial gas jet develops to axial jet, and the performance of atomizing and mixing can be improved. In this study, the Weber number and the ratio of momentum flux were controlled by changing the gas injection area and the mass flow rate of the gas jet, and a study on the spray characteristics at the cold-flow test using water and air simulant was performed. It is concluded that the radial momentum transfer concept of a coaxial porous injector gives a positive effect on the atomization and mixing of the two-phase spray.

• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.167-173
• /
• 2014

The spray characteristics of Gas-Centered Swirl Coaxial Injector was investigated that there were different characteristics with or without gas flow. As gas flow was accelerated, the momentum of gas was transferred to the momentum of liquid in the low liquid Reynolds number. Therefore, the axial velocity of liquid was increased and the measured value was smaller than without gas flow. However, in the high momentum flux ratio, the momentum transfer hardly occurred and the results had constant values. As the recess length was increased, the mixing area of gas and liquid also was increased, the results were decreased.