• 건축사
• /
• 11호통권82호
• /
• pp.26-35
• /
• 1975

The present Structuralists have usually calculated the end Moment of Rigid-frame members by using the Moment Distribution Method, presented by Hardy Cross in 1930, on the Basis of Elastic Law. But this method is considered to be an unfinished solution in case of the moment condition, which the Non-Equilibrium distributed loads or the Horizontal Force acted upon it result in deflection. Hence, after finishing the calculation of stress by means of the Moment Distribution Method, the stress condition due to Horizontal Forces had to be corrected approximatly. However we can directly get the solution of Rigid-frame having sidesway not by above method but by the Moment Distribution computation. Consequently this method is regarded as a Perfect Moment Distribution Method. Here 1 present.

• 한국전산구조공학회논문집
• /
• 제13권1호
• /
• pp.13-24
• /
• 2000

교량 바닥판 설계에 대한 현 시방규정은 바닥판 슬래브가 처짐이 구속된 거더에 연속 지지되어 있다고 가정하므로, 바닥판 지간 중앙의 정모멘트와 거더 상단에 발생하는 부모멘트의 크기가 같은 것으로 간주하고 있다. 그러나 바닥판에 발생하는 휨모멘트는 거더의 처짐에 의해서 많은 영향을 받고 있으며, 거더의 처짐을 고려치 않는 현 시방규정에 의해 설계된 바닥판은 상부철근의 부식으로 인한 내구성 저하와 유지보수 비용 증가 등의 문제점을 안고 있다. 따라서 본 연구에서는 매크로 요소를 이용해 거더의 처짐 효과를 고려할 수 있는 해석법을 개발하였고, 이를 유한요소법을 통해 검증하였다. 또한, 이 해석법을 바탕으로 바닥판의 횡방향 휨모멘트에 영향을 미치는 여러 변수에 대한 분석을 수행하였다. 해석 결과, 바닥판의 지점부 모멘트는 거더의 간격뿐만 아니라 거더와 바닥판의 휨강성비 교량의 길이, 하중의 재하위치, 거더의 비틀림 강성, 가로보의 휨강성과 배치 간격 등에 많은 영향을 받고 있는 것을 알 수 있으며, 영향선을 이용해 최대하중 위치를 결정하여 몇 개의 예제교량을 대상으로 지점부의 설계모멘트를 계산해 본 결과, 현 시방규정이 다소 보수적인 값을 나타내고 있다.

• Structural Engineering and Mechanics
• /
• 제50권6호
• /
• pp.755-772
• /
• 2014

A simplistic approach towards evaluation of complete load deflection response of Reinforced Concrete (RC) flexural members under post fire (residual) scenario is presented in this paper. The cross-section of the RC flexural member is divided into a number of sectors. Thermal analysis is performed to determine the temperature distribution across the section, for given fire duration. Temperature-dependent stress-strain curves for concrete and steel are then utilized to perform a moment-curvature analysis. The moment-curvature relationships are obtained for beams exposed to different fire durations. These are then utilized to obtain the load-deflection plots following pushover analysis. Moreover one of the important issues of modeling the initial stiffness giving due consideration to stiffness degradation due to material degradation and thermal cracking has also been addressed in a rational manner. The approach is straightforward and can be easily programmed in spreadsheets. The presented approach has been validated against the experiments, available in literature, on RC beam subjected to different fire durations viz. 1hr, 1.5hrs and 2hrs. Complete load-deflection curves have been obtained and compared with experimentally reported counterparts. The results also show a good match with the results obtained using more complicated approaches such as those involving Finite element (FE) modeling and conducting a transient thermal stress analysis. Further evaluation of the beams during fire (at elevated temperatures) was performed and a comparison of the mechanical behavior of RC beams under post fire and during fire scenarios is made. Detailed formulations, assumptions and step by step approach are reported in the paper. Due to the simplicity and ease of implementation, this approach can be used for evaluation of global performance of fire affected structures.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권3호
• /
• pp.93-100
• /
• 2008

혹독한 자연환경하에서의 구조물의 내구성이 주요한 관심사도 대두되면서 건설분야에서 섬유강화폴리머의 사용이 점차 증가하고 있는 추세이다. 본 연구에서는 FRP bar를 휨부재의 휨보강근으로서의 적용가능성을 평가하기 위하여 휨실험을 수행하였다. 탄소섬유, 유리섬유 및 탄소와 유리섬유를 혼합한 hybrid 섬유 보강근을 사용하여 보강량을 변화시킨 12개의 실험체를 제작하여 실험을 수행하였으며, 그결과는 파괴형태, 모멘트-변위, 휨강도, 연성지수 및 단면에서의 변형율분포 등에 대하여 분석하였다. 실험결과는 ACI 기준에 제시된 모델과 비교하였으며, 전체적으로 보의 휨강도는 강도설계이론에 의한 결과와 거의 유사한 것으로 나타났다. 그러나 처짐의 경우에는 유리섬유의 경우는 이론이 과대평가 되었으며, 탄소섬유는 과소평가되는 것으로 나타났다.

• 한국건설순환자원학회논문집
• /
• 제9권2호
• /
• pp.143-151
• /
• 2021

이 논문에서는 철근 부식을 촉진시킨 휨 부재의 4점 재하 재하실험을 통하여 철근 지름 및 부식률의 변화에 따른 처짐과 곡률 및 균열모멘트의 변화를 측정하는 실험을 수행하였다. 부식률은 중량비로 0%, 2%, 5% 및 10%로 변화하였으며, 철근의 지름은 각각 10mm, 13mm 및 19mm로 하였다. 실험 결과에 따르면 처짐에 대한 철근 지름의 영향은 크지 않았으며, 철근의 부식률이 2%를 초과하는 경우 부식되지 않은 철근을 가진 부재에 비하여 처짐이 증가하고 균열모멘트가 감소하는 경향을 확인하였다. 이는 부식된 철근에 대한 직접인발 시험과 동일한 경향을 보이는 것이며, 철근의 부식률이 크지 않은 경우 휨거동에 대한 부식의 영향이 크지 않음을 의미한다. 또한, 철근이 부식된 철근콘크리트 부재의 처짐량을 산정하기 위하여 부식률에 따른 균열모멘트의 변화를 반영하는 처짐 보정계수를 도출하고 실험결과를 통하여 그 적용성을 확인하였다.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.44-49
• /
• 2011

The crawler crane, which consists of a lattice boom, a driving system, and movable vehicle, is widely used in a construction site. It needs to be installed an overload limiter to prevent the overturning accident and the fracture of structure. This research is undertaken to provide the relation formula for designing the overload limiter as follows: First the relation formulas between the wire-rope tension and the hoisting load or the overturning ratio according to the luffing angle and length of a lattice boom are established. Secondly the derived formulas are corrected by using the compensated angle considering the deflection of boom through the finite element analysis. The stiffness analysis is carried out for 30-kinds of models as a combination of 6-kinds of luffing angle and 5-kinds of length of boom. Finally the shape design of a stick type load cell, which is the device to measure the wire-rope tension, is performed. 5-kinds of notch radius and 5-kinds of center hole radius are adopted as the design parameter for the strength analysis of the load cell.

• 한국산학기술학회논문지
• /
• 제12권2호
• /
• pp.936-943
• /
• 2011

ACI 440.1R-06 설계지침에서는 FRP-보강근 콘크리트 부재의 처짐 계산을 위해 Branson에 의해 제안된 유효단면2차모멘트를 수정 보완하여 제시하고 있다. 그러나 다수의 연구자들은 아직까지도 적용범위의 적절성에 대해 의문점을 제기하고 있다. 이에 본 연구에서는 12개의 장방형 단면과 9개의 T형단면의 FRP-보강근 콘크리트 시험체를 제작하여 처짐 실험을 통해 얻어지는 실험값과 제안된 이론식에 의해 얻어진 계산값을 비교 분석하여 합리적인 처짐설계를 위한 기초자료를 제안하고자 하였다. 결과로서 FRP-보강근 콘크리트 보의 처짐값은 장방형단면에서는 계산값이 실험값 보다 과소평가 되었으나, T형단면에서는 계산값이 실험값 보다 다소 과대평가 되어 나타났다.

• Structural Engineering and Mechanics
• /
• 제78권3호
• /
• pp.255-267
• /
• 2021

The analysis of simply supported single-cell skew-curved reinforced concrete (RC) box-girder bridges is carried out using a finite element based CsiBridge software. The behaviour of skew-curved box-girder bridges can not be anticipated simply by superimposing the individual effects of skewness and curvature, so it becomes important to examine the behaviour of such bridges considering the combined effects of skewness and curvature. A comprehensive parametric study is performed wherein the combined influence of the skew and curve angles is considered to determine the maximum bending moment, maximum shear force, maximum torsional moment and maximum vertical deflection of the bridge girders. The skew angle is varied from 0° to 60° at an interval of 10°, and the curve angle is varied from 0° to 60° at an interval of 12°. The scantly available literature on such bridges focuses mainly on the analysis of skew-curved bridges under dead and point loads. But, the effects of actual loadings may be different, thus, it is considered in the present study. It is found that the performance of these bridges having more curvature can be improved by introducing the skewness. Finally, several equations are deduced in the non-dimensional form for estimating the forces and deflection in the girders of simply supported skew-curved RC box-girder bridges, based upon the results of the straight one. The developed equations may be helpful to the designers in proportioning, analysing, and designing such bridges, as the correlation coefficient is about 0.99.

• Geomechanics and Engineering
• /
• 제16권3호
• /
• pp.309-320
• /
• 2018

In this paper, a numerical study using finite element method with considering soil-structure interaction was conducted to investigate the stress and deformation behavior of a sheet pile wall structure. In numerical model, one of the nonlinear elastic material constitutive models, Duncan-Chang E-v model, is used for describing soil behavior. The hard contact constitutive model is used for simulating the behavior of interface between the sheet pile wall and soil. The construction process of excavation and backfill is simulated by the way of step loading. We also compare the present numerical method with the in-situ test results for verifying the numerical methods. The numerical analysis showed that the soil excavation in the lock chamber has a huge effect on the wall deflection and stress, pile deflection, and anchor force. With the increase of distance between anchored bars, the maximum wall deflection and anchor force increase, while the maximum wall stress decreases. At a low elevation of anchored bar, the maximum wall bending moment decreases, but the maximum wall deflection, pile deflection, and anchor force both increase. The construction procedure with first excavation and then backfill is quite favorable for decreasing pile deflection, wall deflection and stress, and anchor forces.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제20권1호
• /
• pp.17-35
• /
• 2016

In this study, the dynamic behaviour of a rotating Timoshenko beam when under the actions of a variable magnitude load moving at non-uniform speed is carried out. The effect of cross-sectional dimension and damping on the flexural motions of the elastic beam was neglected. The coupled second order partial differential equations incorporating the effects of rotary and gyroscopic moment describing the motions of the beam was scrutinized in order to obtain the expression for the dynamic deflection and rotation of the vibrating system using an elegant technique called Galerkin's Method. Analyses of the solutions obtained were carried out and various results were displayed in plotted curve. It was found that the response amplitude of the simply supported beam increases with an increase in the value of the foundation reaction modulus. Effects of other vital structural parameters were also established.