• Bulletin of the Korean Chemical Society
• /
• v.33 no.3
• /
• pp.881-884
• /
• 2012

We report a quantum chemical study of an extremely efficient nucleophilic aromatic fluorination in molten salts. We describe that the mechanism involves solvent anion interacting with the ion pair nucleophile $M^+F^-$(M = Na, K, Rb, Cs) to accelerate the reaction. We show that our proposed mechanism may well explain the excellent efficiency of molten salts for SNAr reactions, the relative efficacy of the metal cations, and also the observed large difference in rate constants in two molten salts $(n-C_4H_9)_4N^+\;CX_3SO_3^-$, (X=H, F) with slightly different sidechain ($-CH_3$ vs. $-CF_3$).

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.86-91
• /
• 2011

Thermal design was conducted for a solar thermal storage system in a medium-temperature range between $200^{\circ}C$ and $400^{\circ}C$. The system was composed of heat pipes as heat carrier and molten salts as phase-change storage material. Each heat pipe penetrated through the storage system and had two heat-exchanging sections at both ends to interact with high-and low-temperature steams, while it exchanged heat with molten salts in the middle section. During a heat-storage mode, the heat pipes transferred heat from the hot steam at one side to the molten salts and it transferred heat from the molten salt to the cold steam at the other side during the heat-dissipating mode. A tube-bank type heat exchanger theory was applied to this design task to meet the required inlet and outlet temperatures of the steams depending on the operation modes. Several design variables were considered including the lengths of evaporator and condenser of a heat pipe, traverse and longitudinal pitches of the pipe, and the number of rows of the heat pipes for two different molten salt baths. An optimum design results were presented with discussion.

• Nuclear Engineering and Technology
• /
• v.32 no.5
• /
• pp.514-520
• /
• 2000

The mechanism of corrosion behavior has to be understood clearly to select an optimum material for handling molten salts to be used in the oxide reduction process of PWR spent fuel. In this study, the oxidation states of corrosion products on the surface of Inconel 600 and 800H as well as their chemical compositions and structural informations were determined by using XPS, ICP-AES, AAS, EPMA and XRD after the corrosion experiment with lithium molten salts at 75$0^{\circ}C$ for 25 hours. Nickel and oxygen were detected from the corrosion products on the surface of Inconel plates and chromium was found to be dissolved out into lithium molten salts leaving cracks on the surface. The corrosion products were identified as metal oxides such as Fe$_2$O$_3$, Cr$_2$O$_3$, NiO, NiFe$_2$O$_4$and MnO by using XPS and XRD.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.4
• /
• pp.207-212
• /
• 2009

In this study, a thermal behavior of $PrCl_3$ as one of the lanthanide chlorides in LiCl-KCl molten salts was investigated in an oxidizing condition. First, a thermo-gravimetric analysis (TGA) of $PrCl_3$ was carried out by an injection of $O_2$ gas. Based on the results, an oxidation of $PrCl_3$ in the molten salts was performed by sparging $O_2$ gas with changing temperatures. According to the TGA data of $PrCl_3$, a dissociation of $PrCl_3$ occurred rapidly by about $380^{\circ}C$ and a conversion of $PrCl_3$ to $PrCl_3$ was completed at about $600^{\circ}C$. The thermal behavior of $PrCl_3$ in LiCl-KCl molten salts by sparging $O_2$ gas was similar to that of $PrCl_3$ in the TGA test, and PrOCl as a insoluble compound in the molten salts was precipitated into the bottom of the molten salts. A conversion of $PrCl_3$ to PrOCl in the molten salts occurred actively at a higher temperature than $650^{\circ}C$. And it would be possible to estimate a conversion status of $PrCl_3$ to PrOCl by measuring a $Cl_2$ concentration in a flue gas generated from an oxidation test of $PrCl_3$ in LiCl-KCl molten salts.

• Korean Journal of Materials Research
• /
• v.28 no.7
• /
• pp.423-427
• /
• 2018

For diamond/metal composites it is better to use diamond particles coated with metal carbide because of improved wettability between the diamond particles and the matrix. In this study, the coating of diamond particles with a chromium carbide layer is investigated. On heating diamond and chromium powders at $800{\sim}900^{\circ}C$ in molten salts of LiCl, KCl, $CaCl_2$, the diamond particles are coated with $Cr_7C_3$. The surfaces of the diamond powders are analyzed using X-ray diffraction and scanning electron microscopy. The average thickness of the $Cr_7C_3$ coating layers is calculated from the result of the particle size analysis. By using the molten salt method, the $Cr_7C_3$ coating layer is uniformly formed on the diamond particles at a relatively low temperature at which the graphitization of the diamond particles is avoided. Treatment temperatures are lower than those in the previously proposed methods. The coated layer is thickened with an increase in heating temperature up to $900^{\circ}C$. The coating reaction of the diamond particles with chromium carbide is much more rapid in $LiCl-KCl-CaCl_2$ molten salts than with the molten salts of $KCl-CaCl_2$.

• Journal of the Korean Society of Safety
• /
• v.4 no.1
• /
• pp.41-46
• /
• 1989

Molten salt-water explosion caused by the contact between molten salt and water is one of vapour explosions. An experimental study of the vapour explosion, which occurs when the molten mixture of Na$_2$CO$_3$-NaOH and water come in contact was performed. The pressure wave generated in each composition Of molten mixtures was measured. The results obtained are as follows： 1) The vapour explosion didn't occur for a molten salt of 100%-Na$_2$CO$_3$- 2) For a molten salt of Na$_2$CO$_3$ 80％-NaOH 20% mixture, a small vapour explosion occured initially, and a large vapour explosion, which showed the largest pressure wave among the present experiments, occurred after an induced period. 3) For molten salt of Na$_2$CO$_3$60％ - NaOH 40％ mixture and Na$_2$CO$_3$ 40％ - NaOH 60％ mixture, the vapour explosion occurred near the water surface shortly after they come in contact with water. This explosion would be caused by fragmentation of the molten salts due to impulse generated when thee molten salts and water come in contact.

• Journal of the Korean Ceramic Society
• /
• v.45 no.8
• /
• pp.464-471
• /
• 2008

The electrolyte separator for thermal battery should be easily handled and loaded a large amount of the molten salt. Ceramic fibers, especially fibrous commercial glass filters were used as an electrolyte separator and the lithium based molten salts were infiltrated into the ceramic filters. The pore structures of the ceramic filter and the melting properties of the lithium salts affected to the electrolyte loading and leakage. During the infiltration, ions of $Li^+$ and $F^-$ in the molten salts were reacted with the glass fiber and caused to be weaken the fiber strength.

• Journal of the Korean Chemical Society
• /
• v.14 no.3
• /
• pp.263-269
• /
• 1970

A theory of surface tension developed by using the approximation that the surface of liquids consists of a monomolecular layer has been applied to the molten salts (NaCl, KCl, NaBr, KBr) and the strong electrolyte solutions. By considering that the ionic forces are the long-range forces and with the use of the partition functions developed, the surface tension of molten salts and strong electrolyte solutions has been calculated. The results show good agreement between theory and experiment at various temperatures and over a wide concentration ranges (0.1-4.0m)

• Journal of the Korean Ceramic Society
• /
• v.30 no.7
• /
• pp.543-548
• /
• 1993

Stability and formation of Pb(Mg1/3Nb2/3)O3 (PMN) phase synthesized in Li2SO4-Na2SO4 molten salts have been investigated. And powder characteristics of PMN have been studied with a variation of processing parameters such as temperature, time, amount of the salts, and excess PbO. More ratio of Li2SO4 to Na2SO4 influences the percentage of perovskite phase due to the difference of the eutectic point of the salts, but does not influence the powder characteristics. The shape of PMN particles shows faceted morphology with bimodal distribution consisting with large and submicron parts. Particle size of PMN increased greatly with increasing soaking time or amount of salts rather than temperature. The addition of excess PbO resulted in round PMN crystallites without submicron particles. These results are discussed by XRD, SEM and thermal analyses.

• Korean Journal of Materials Research
• /
• v.25 no.12
• /
• pp.694-702
• /
• 2015

Nd-Fe-B permanent magnets have been used in a wide variety of applications because of their high magnetic flux density. So, demand for neodymium has been increasing in worldwide. In this study, an electrowinning process was performed in $LiF-NdF_3-Nd_2O_3$ high temperature molten salts. However, a corrosion resistant material for use in the molten salt must be found for stable operation because of the harsh corrosion environment of the electrowinning process. Therefore, for this paper, boron nitride(BN), aluminum nitride(AlN), and silicon nitride($Si_3N_4$) were selected as protective and structural materials in the high temperature electrolyte. To investigate the characteristics of BN, AlN, and $Si_3N_4$, in molten salts, materials were immersed in the molten salts for 24, 72, 120, and 192 hours. Also, surface condition and stability were investigated by SEM and EDS and corrosion products were calculated by HSC chemistry. As a result, among BN, AlN, and $Si_3N_4$, AlN was found to show the best protective material properties.