• Design & Manufacturing
• /
• 제2권5호
• /
• pp.30-33
• /
• 2008

Injection Molding is the most effective process for mass production of plastic parts. The injection molding process is composed with several steps such as Filling, Packing, Holding, Cooling, Ejecting. Among them, filling and packing process should be considered carefully to improve accuracy of dimension, surface quality of plastic parts. Usually the quality above-mentioned is managed with weight of part after molding on the field. In this paper, a series of experiment for molding automotive front bumper was conducted with cavitity temperature sensor to optimize switch-over time(V-P switching), hot runner vale gate sequence time during filling and packing step for the purpose of uniform quality, weight at every molding. As a result, it was found that it is effective method to use temperature sensor in injection molding for quality control of plastic molding.

• Composites Research
• /
• 제31권1호
• /
• pp.12-16
• /
• 2018

복합소재와 금형강 간에는 열팽창계수의 차이로 인하여 성형 과정 중의 온도 구배에 따라 다른 열팽창길이를 갖는다. 따라서 금형 내에 복합소재를 삽입하여 성형을 하는 경우 복합소재의 표면에 작용하는 압력이 소재의 업체에서 추천하는 성형 압력을 유지하는지를 확인할 필요성이 있다. 본 연구에서는 온도의 차이에 따른 복합소재와 금형 사이의 압력을 유한요소해석법을 사용하여 예측하였으며 열팽창에 따른 금형의 길이를 측정함으로써 해석의 정확성을 검증하였다. 각 온도에서의 해석과 실험값의 차이로써 매우 근사한 값을 얻을 수 있었으며, 틈새 예측 값의 목표치인 ${\pm}0.05mm$ 안에 들어오는 것을 확인하였다. 이를 통하여 복합소재에 작용하는 압력을 추정한 해석값이 신뢰할 수준임을 알 수 있었다.

• 한국주조공학회지
• /
• 제13권6호
• /
• pp.532-539
• /
• 1993

The effect of casting variables for making pure Al and Al-5wt%Si alloy rods free from any surface and inside defects was studied by adopting the horizontal continuous casting method with heated mold. The rods were cast under the casting conditions such as the mold temperature of $670{\sim}690^{\circ}C$, water flow rate of $0.2{\sim}0.6{\ell}/min$, and rod diameter of $4{\sim}8mm$, when the melt temperature and mold to cooler distance was fixed at $700^{\circ}C$ and 20mm, respectively. The results represented that the casting speed for good quality rod increased as the water flow rate increased, whereas, the casting speed decreased as the rod diameter or mold temperature increased. The statistical analysis of $2^3$ factorial design was also applied and the results represented that the averaged optimum casting speed for pure Al(302mm/min) was higher than that of Al-5wt%Si alloy(273mm/min) resulting from the difference of superheat applied. The effect of rod diameter on the optimum casting speed was the highest for pure Al as well as Al-5wt%Si alloy. The effect of water flow rate and mold temperature on the optimum casting speed was in decreasing order.

• 한국주조공학회지
• /
• 제29권5호
• /
• pp.238-243
• /
• 2009

This study has been carried out to investigate the cooling ability improvement of diecasting mold by decompression cooling system. The decompression cooling system was applied to the new/used oil pump cover molds. The temperature of the surface mold applied the decompression cooling system fell to 15 degrees, especially in case of the used mold. The defect ratio of the oil pump cover manufactured by decompression cooling system has decreased from 2.8 percent to 0.2 percent. According to the results of the cooling ability improvement of diecasting mold by decompression cooling system, the decompression degree and supply pressure were set up the control item to apply the decompression cooling system to the diecasting mold in the industry field.

• 한국금형공학회:학술대회논문집
• /
• 한국금형공학회 2008년도 하계 학술대회
• /
• pp.69-73
• /
• 2008

본 연구에서는 고분자 플라스틱 부품의 친환경 외장성형공법인 Insert Film 사출성형공법중 첫 번째 공정인 진공성형공정에서 진공금형의 표면온도 균일화 기술에 대해 연구를 수행하였다. 진공금형의 온도분포 균일화를 위한 금형설계 및 설계된 금형에 대한 온도분포 평가를 위한 ANSYS를 이용한 유한요소열해석을 수행하였으며, 이때 정상상태 및 과도상태를 함께 평가하였다. 설계 결과를 바탕으로 금형을 제작하였으며, 생산성을 고려하여 4캐비티로 제작된 금형에 대해 금형표면의 온도분포 평가실험을 수행하였다. 또한 금형내 캐비티 온도센서 및 제어시스템을 설치하여 진공금형표면 온도분포가 항상 일정하게 유지될 수 있도록 금형시스템을 개발하였다. 결과적으로 일정한 온도범위의 금형표면온도제어가 가능하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 금형가공,미세가공,플라스틱가공 공동 심포지엄
• /
• pp.23-28
• /
• 2005

Microlens arrays were fabricated using a modified LIGA process based on the exposure of a PMMA (Polymethylmethacrylate) sheet to deep x-rays and subsequent thermal treatment. A successful modeling and analyses for microlens formation were presented according to the experimental procedure. A nickel mold insert was fabricated by the nickel electroforming process on the PMMA microlens arrays fabricated by the modified LIGA process. For the replication of microlens arrays having various diameters with different foci on the same substrate, the hot embossing and the microinjection molding processes have been successfully utilized with the fabricated mold insert. Fabricated microlenses showed good surface roughness than the mold insert. The focal lengths of the injection molded microlenses were successfully measured experimentally and also estimated theoretically.

• 전기학회논문지
• /
• 제66권6호
• /
• pp.962-967
• /
• 2017

The Diamond-Like-Carbon (DLC) coating is a new carbon-based amorphous material. Carbon ions in the plasma are electrically accelerated and collide with the substrate to form a thin film. This film has similar properties to diamonds such as high surface hardness, low coefficient of friction, corrosion resistance and durability that do not react with acids and bases. Also, since there is no thermal deformation, it can be printed at room temperature. and coated on almost all materials such as paper, polymer, ceramics and various metals even aspheric lens it is possible to mirror surface coating with excellent surface roughness. In this paper, we have analyzed the DLC film formed by Filtered Arc Ion Plating (Filtered AIP) process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The Korea-Japan Plastics Processing Joint Seminar
• /
• pp.1-6
• /
• 2003

In injection molding of an optical disk, a toric lens, etc., their performance depends on the transcription preciseness of fine surface structure of a mold. However, transcription behavior has not been made clear yet, because transcription is made in very short time and the structure is very small. In this paper, transcription properties have been examined, by using V-grooves of various sizes. machined on mold surfaces, and the following results are obtained. (1) Transcription properties have been made clear experimentally and it was found that the mold temperature $T_D$ makes great influence on the transcription property and that compression applying time $t_c$ should be taken more than 2.0s for fine transcription. (2) A mechanical model of transcription process, in consideration with strain recovery due to viscoelastic property of polymer. is proposed. (3) Simulation results agree with experimental ones fairly well. It means that the transcription model is useful for estimation of transcription property in advance of an actual. injection molding.

• 한국산학기술학회논문지
• /
• 제4권3호
• /
• pp.164-167
• /
• 2003

본 연구에서는 무선부품의 일종인 cavity filter금형을 제작하여 도금용 ABS 수지와 PC/ABS alloy 수지를 사용하여 일반사출성형과 금형온도가 높은 MmSH방식, 두 타입으로 성형품을 제작하였다. 성형품의 수축률 변화는 MmSH 방식일 때 ABS 성형품의 단위캐비티 격막부분에서 수축률이 감소되었다. 중량변화는 ABS와 PC/ABS 성형품 모두 MmSH 방식일 때 증가하였고, 성형품 표면 거칠기는 MmSH 방식일 때 모두 거칠기가 감소되었다.

• 대한치과기공학회지
• /
• 제29권1호
• /
• pp.133-138
• /
• 2007

In this study, the castability and of commercially pure titanium(c.p.Ti) grade according to the casting condition which are the vacuum condition in casting machine and mold temperature of investment, was investigated. Argon-arc melt/centrifugal casting machine was used for casting the specimens. The microstructure and mechanical properties were evaluated by using optical microscope. The results were as follows; 1. It could make a sure that there's relatively not much defect of casting body of c.p.Ti according to the deference of air pressure. 2. It could make sure that it formed porosity on the surface inside of the casting body of c.p.Ti according to deferent temperature. and on excellent castability was below $200^{\circ}C$ 3. As the mold temperature of investment was increased, the lamellar structure of phase and coarse grains were shown, especially under 42MPa.