• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1754-1759
• /
• 2008

To produce plastic parts that have fine pattern through conventional injection molding, a lot of difficulties follow. Therefore, rapid heating and cooling methods are good candidates for manufacturing injection-molded parts with micro/nano patterns. In this study, we adopted the E-Mold patent technology. The mold for E-Mold technology has a separate heated core with micro heaters. It is very important to optimize the lay-out of the heaters in heated core because it influences both control and distribution of mold temperature. We developed a optimization method of heating line lay-out by using commercial softwares and compared the output with the experimental results. We used Pro-Engineer Wildfire 2.0 for the mold design, ICEMCFD for mesh generation, and FLUENT for heat transfer simulation. The simulation results showed the temperature profile from $60^{\circ}C$ to $120^{\circ}C$ or $180^{\circ}C$ during heating and cooling process which were compared with the injection molding experiments. We concluded that the simulation could well explain the experimental results. It was shown that the E-Mold optimization design for heater lay-out could be available through the simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.741-742
• /
• 2008

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.195-198
• /
• 2007

The present work focuses on the prediction of birefringence in injection-molded plastic part and its improvement by rapid mold heating. To calculate birefringence, flow-induced residual stress is computed through a fully three-dimensional injection molding analysis. Then the stress-optical law is applied from which the order of birefringence can be evaluated and visualized. The birefringence patterns are predicted for a rectangular plate with a variation of mold temperatures, which shows that the amount of molecular orientation and birefringence level decreases with an increase of mold temperature. The effect of mold temperature on the order of birefringence is also studied for a thin-walled rectangular strip, and compared with experimental measurements. Both predicted and experimental patterns of birefringence are in agreements on the observation that the birefringence level diminishes significantly when the mold temperature is raised to above the glass transition temperature.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.9 s.174
• /
• pp.173-178
• /
• 2005

Recently plastic parts are molded for the purpose of mass production in multi-cavity system. Therefore, designer is usually designing mold that has geometrically balanced runner lay-out for filling balance at each cavity. Although, mold is manufactured with geometrically balanced runner lay-out, there are actually filling imbalances in the cavities. These filling imbalances phenomenon are caused by complicated interaction between melt and mold. In this study, based on previous studies for filling imbalances in cold-runner mold, filling imbalances in hot-runner mold were investigated by CAE and injection molding experiments. ABS and PMMA as amorphous polymer, PA as crystalline polymer were used to compare the filling imbalances. There were different results of CAE and experiment. The filling imbalances decreased as injection rate increased without regard to kind of resins and were lower than the one of cold-runner.

• Structural Engineering and Mechanics
• /
• v.74 no.4
• /
• pp.559-565
• /
• 2020

This paper intends to progress models to accurately estimate the behavior of fresh concrete under vibration using artificial neural networks (ANNs). To this end, behavior of a full scale precast concrete mold was investigated numerically. Experimental study was carried out under vibration with the use of a computer-based data acquisition system. In this study measurements were taken at three points using two vibrators. Transducers were used to measure time-dependent lateral displacements at these points on mold while both mold is empty and full of fresh concrete. Modeling of empty and full mold was made using ANNs. Benefiting ANNs used in this study for modeling fresh concrete, mold design can be performed. For the modeling of ANNs: Experimental data were divided randomly into two parts such as training set and testing set. Training set was used for ANN's learning stage. And the remaining part was used for testing the ANNs. Finally, ANN modeling was compared with measured data. The comparisons show that the experimental data and ANN results are compatible.

• Design & Manufacturing
• /
• v.9 no.3
• /
• pp.24-28
• /
• 2015

Speaking in general terms the form injection process can be described as a new process-variant of already known structural foam molding technology which roots go back to the early sixties. The most limiting factors of already know foaming processes are large cell size and the lack of uniformity of these cells as well and the inability to foam all kinds of plastic materials. In this paper, Process Study on weight change in injection rate during foaming. Experimental conditions were set as the injection speed 50,150,300 and 450 mm/s. The experiments PA, PA+GF, PP, was confirmed that the weight increase to PP+TA.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1995.10a
• /
• pp.64-67
• /
• 1995

Transfer Molding is currently the most widely used process for encapsulation integrated circuits(;IC). Although the process has been introduced over 20 years ago, generating billions of parts each year, it is far from being optimized. With each new mold, epoxy mold, epoxy mold compound, and lead-frame, lengthy period and expensive qualification runs have to be performed to minimized defects ranging from wire sweep, incomplete fill, and internal voids etc. This studies describes how simulation can be applied to transfer molding to yield acceptable design and processing parameter. The non-isothermal filling of non-newtonian reactive epoxy molding compound(;EMC) in a multi-cavity mold is analyzed. Sensitivity analysis is conducted to investigate the influence of process deviations on the final molded profile. This study trend is carried out by following some heuristic process guidelines.

• Design & Manufacturing
• /
• v.12 no.2
• /
• pp.51-56
• /
• 2018

Generally, The women was used in the cosmetic cushion fact. It has developed with the consideration of manufacturing. In this study, we designed green-friendly and element parts lower and single cushion fact containers using a single material. Injection mold simulation were performed using on 3D design data. The injection mold simulation used the data (Injection time / Cooling time / Temperature / Pressure) in the injection mold parameters. In addition, the sink mark phenomenon in the simulation results is analyzed as a problem due to the thickness and further research is needed in the future.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.5
• /
• pp.594-600
• /
• 2007

Rapid mold heating has been recent issue to enable the injection molding of thin-walled parts or micro/nano structures. Induction heating is an efficient way to heat a conductive workpiece by means of high-frequency electric current caused by electromagnetic induction. Because the induction heating is a convenient and efficient way of indirect heating, it has various applications such as heat treatment, brazing, welding, melting, and mold heating. The present study covers an experimental investigation on the rapid heating using the induction heating and rapid cooling using a vortex tube in order to eliminate an excessive cycle time increase. Experiments are performed in the case of a steel cup mold core with various heating and cooling conditions. Temperature is measured during heating and cooling time, from which appropriate mold heating and cooling conditions can be obtained.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.129-133
• /
• 2008

As a rotating machine element, plastic gears are more and more widely used in such as industrial machine element, since plastic gear is lighter, higher wear-resistance, and higher vibration absorbing ability than metal gears. When operating plastic parts, tooth breakage and fatigue life shortened due to increasing number of applying load and tooth flank temperature rising, such that accuracy of plastic gears is divided from allowable range to cause vibration and noise. On this study, a internal plastic gears are developed which improved the filling balance molding process by a new injection mold structure. The new mold structure called HR3P(hot runner type 3plate mold). As the result from this studies, we obtained a very accurate roundness internal gears by using design of experiment.