• Design & Manufacturing
• /
• 제2권3호
• /
• pp.16-21
• /
• 2008

In recent, the demands of household cases and disposable products is increased significantly because a living standard of newly-emerging nations was risen. Therefore, multi-cavity mold and stack mold for the realization of high-productivity have been researched in forefront nations. In this paper, CAE analysis for minimizing the mold core deformation was performed. Finally, 64 cavities injection mold for molding cap which has the insert-type core was fabricated according to the result of CAE analysis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.99-100
• /
• 2007

Transferring patterns from mold to PDMS stamp is very useful technology in micro-fabrication, complex and three-dimensional structures. First experimentation, mold's patterns wens transferred to PDMS stamp. Comparing with PDMS stamp and Mold, patterns were transferred about 97.9%. Second experimentation, PDMS stamps were made several times by only one mold, scale and distance of transferred patterns were uniform about 89.3%. We proved that transferring patterns from mold to PDMS stamp is accurate. The uniformity of stamps is the same after mold was used several times. Transferring patterns from mold to PDMS stamp has uniformity and accuracy, it will be useful technology.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 1997년도 International Symposium on Fire Science and Technology
• /
• pp.219-226
• /
• 1997

This paper investigates and analyzes the installation and failure status of mold transformer being used in domestic subways and describes the extinguishing process by time through the combustion test of winding part of mold transformer. Condition of installed mold transformers and classes of fire were surveyed and the mold transformer was burned in a horizontal heating furnace. It was confirmed that the mold transformer is self extinguishing and nonflammability. According to this results, the suitable standard of fire protection for the mold transformer was demanded after review of domestic and abroad law. It is expected that the cost of fire protection equipment can be reduced by using the status and combustion test result of mold transformer.

• 펄프종이기술
• /
• 제48권1호
• /
• pp.67-74
• /
• 2016

The demand of environmental friendly packaging materials such as pulp mold has been increased. The application of the oil palm biomass, EFB (Empty Fruit Bunch) fiber as natural raw materials to the pulp mold could increase the usability of the pulp mold by the reduced production cost brought from the relatively low cost of EFB. The effects of the EFB(Empty Fruit Bunch) fibers on the properties of pulp mold and on the process efficiency were evaluated in this study. The pulp mold samples were prepared with mixture ONP (Old news paper) and EFB by using laboratory wet pulp molder. The changes in the drying efficiency were measured with the changes in the solid contents of pulp mold samples during drying process. The efficiency of the surface coating treatment on the pulp mold depending on the condition of the pulp mold samples were also evaluated in order to improve the water resistance properties of pulp mold. The addition of EFB increased the drying efficiency by providing the bulkier structure and the higher water contact angle, which indicated the better water resistance properties. The water resistance were improved by the surface coating treatments and the application of surface coating on the pulp mold at the higher moisture contents resulted in the higher improvement in the water resistance. The bulkier structure originated from the application of EFB fiber reduced the effects of the surface coating, which could be overcome by the control of surface coating process.

• 한국주조공학회지
• /
• 제21권4호
• /
• pp.253-259
• /
• 2001

There are many methods to produce metal foams, which can be classified into three groups according to the state of the starting metal i.e. liquid or powder or solid. Three types of defects such as cell closing, cell deformation or breakdown and cell misrun are thought to be occurred when we make the open cell aluminum foams by precision casting. Filling ability of the mold slurry between preform is related with cell closing, mold collapsibility is related with cell deformation or breakdown, mold temperature and pouring pressure are related with cell misrun. These factors can be evaluated by measuring slurry fluidity, burnout strength and permeability of the mold. Properties of the plaster mold were evaluated to find optimum mold conditions for high quality open cell aluminum foam in this study. Permeability was almost zero independent of burnout conditions, however, crack initiation was found on the surface of all specimens one or two minutes after taking out from the furnace. Crack has grown and disappeared with time. This crack may facilitate the mold filling when molten metal is poured, because of the improved mold permeability. It was considered that crack initiation and disappearance was closely related with temperature difference between the surface and inner part. Knocking-out the mold is a difficult problem due to the small cell size, because continuous mesh structure of the metal foam is not strong. It is not easy to remove molding material after pouring. We can expect that water quenching can facilitate the knocking-out the mold after solidification without damaging cell structures. Collapsed particles after water quenching became bigger with the increase in time.

• 한국주조공학회지
• /
• 제35권2호
• /
• pp.29-35
• /
• 2015

In this study, potential defects of ring-type cast products during the mold-filling stage of the casting process were investigated using computer simulation. The main focus was on the effects of runner extension and ingates. During the mold filling the molten metal flowed from the bottom to the top of the mold in two curved paths along the ring-type cavity. The fluid fronts in the two paths did not show the identical velocity during the mold filling stage. This difference in the filling speeds may cause defects such as voids and local contractions. The present model contained virtual fluid detectors at various positions inside the mold. When the molten metal passed those points, the volume of fluid jumped up from zero to one. The moments were measured to compare the speeds of the fluid fronts. We attempted various combinations of runner extensions and ingates to stabilize the flow and then to optimize the casting mold design.

• Design & Manufacturing
• /
• 제9권1호
• /
• pp.18-22
• /
• 2015

Mold making and product manufacturing process was made by a die through a number of stages. Thereby, it takes a long period of time from the manufacture of mold until passed the products to consumers. However, it is not possible to meet the diverse desires purchasing of consumer. We made a 3D CAD Model aligned with product scan data using reverse engineering. Utilizing thereafter flow analysis to derive the optimal mold conditions, by applying the condition, and devised a mold fabrication process that is much shorter than the conventional process for fabricating a mold. In this study, the outlet cover to the product, it describes a process, as a result, it was confirmed that the number of steps can be shortened much more than the conventional process.

• Design & Manufacturing
• /
• 제2권6호
• /
• pp.49-55
• /
• 2008

Double-injection molding can inject two different materials or two colors in the same mold and process. If this injection process use, product has ability because the base part maintain strength and specified part can inject soft-material. It makes the cost down by single operation automatically for saving wages. In this paper, we designed double-injection mold for automobile remote control to inject secondary using this part as insert after inject external appearance of product. CAE analysis was progressed gate location and runner size as variable and analysis result is reflected in mold design process. As a result, it could solved badness that is generated at the conventional mold. Additionally, cost is downed by reducing loss of runner as well as could omit painting process because surface of finished product is improved through new mold.

• Design & Manufacturing
• /
• 제6권2호
• /
• pp.84-89
• /
• 2012

In recent years, technology of press plastic working having made remarkable progress. We can say this because it facilitates mass production and have superior performances in machining speed and equivalency of quality than other processing methods. In characteristics of press plastic working, mold manufacturing according to characteristics of each product should be preceded before processing and it has a great influence on machining speed and quality of products and etc according to manufacturing method. Therefore, mold design technology is a critical technology in press plastic working. There are lots of variables in press plastic working according to worked material, mold materials, conditions of heat treatment, clearance and so on. Abrasion of mold depends on these kind of conditions and sheared surface which is crucial for quality of product also depends on them. In this study, we conduct research on abrasion loss of mold according to 8, 10 and 12% of clearance for thickness of 1.0mm of worked material out of mold design variables of the products whose worked materials are high carbon steel and carbon tool steel by a practical experiment.

• Design & Manufacturing
• /
• 제8권2호
• /
• pp.12-17
• /
• 2014

Currently, injection molding process is a very useful technique that be applied to many field. And injection molding technology has been commercial based on many studies. However, there is no standard of surface roughness because there are few studies about surface technology of injection product. In addition, when designing the mold, changes of the core surface and the injection conditions are not considered. In this paper, change of surface according to the core and the injection conditions was compared with the surface of the injection product. Accumulation of these technologies will propose direction in mold design, manufacturing and injection molding technology.