• Korean Journal of Environmental Agriculture
• /
• v.10 no.2
• /
• pp.133-137
• /
• 1991

The inorganic constituents in flay ash such as Ca, Mg, Al and Si were extracted by water and 0.5N-Acetic acid, and changes of the physical properties of the fly ash-treated soils were examined to find out the effect of fly ash on the chemical and physical properties of the soils. The dominant day minerals of fly ash were quartz and mullite. More inorganic constituents were extracted from the fly ash by acetic acid than by water. Si and A1 in fly ash were hardly extracted by water. Addition of fly ash to soil below 10%(W/W) caused improvement in the water permeability and the field moisture capacity of the soil, but did not influence the shrinkage and hardness of the soil. Therefore, it was apparent that the effect of the fly ash on the chemical and physical properties of the soils greatly dependedon soil reaction, the organic acid contents, and the amount of fly ash used in treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.1
• /
• pp.15-22
• /
• 1997

The effectiveness of presteaming for improving CCA treatability on refractory Japanese larch heartwood was investigated in this study. Presteaming was effective on improving treatability, and the extent of improvement was dependent on moisture contents of wood specimen and steaming conditions. Green wood showed higher average value in both preservative retention and penetration than dry wood, and steaming under pressure conditions also had higher treatability than steaming at atmospheric conditions. The degree of improvement for treatability was increased with the extension of steaming period. Treatability of dry wood pres teamed under pressure conditions more than 6 hours and green wood for 3 hours was similar to that enhanced by conventional incising. Presteaming green wood under pressure conditions more than 6 hours was more effective than conventional incising in improvement of CCA treatability, and resultant treatability satisfied a minimum value required for CCA-treated wood for being used at the regions of hazard class H3 and H4. In addition, an improvement of treatability by presteaming was due to an increase in permeability resulted from the degradation of hemicelluloses within aspirated pit membrane and cell wall, not the removal of extractives from pit membrane. The reduction in strength, measured as longitudinal compressive strength, due to pres teaming was related with the degradation of hemicelluloses, and was increased as steaming conditions were severe. The degree of strength reduction associated with presteaming treatment to obtain required treatability could be quantified from the relatively good relation between the increase in treatability and the decrease in strength.

• The Journal of Engineering Geology
• /
• v.11 no.3
• /
• pp.245-254
• /
• 2001

The experimental study on disposal cover through the performance test facility offers reliability in the safety of near surface disposal of low and intermediate level radioactive waste. To ensure the long-term safety of the repository, the impermeability, integrity, resistance to degradation and ease of maintenance might be considered as the basic performance requirement of the disposal cover. considering the difficulties to meet these performance requirement by using single layer, the disposal cover design which is composed of top layer, middle drainage layer and bottom low permeability layer is schemed for the test facility. The water balance of the cover was evaluated by using HELP code. For the long-term monitoring of the soil moisture content and matric potential, TDR probes and tensiometers will be installed in 6 test cells. Each test cell is dimensioned 3$\times$3$\times$3.3m.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.1
• /
• pp.1-10
• /
• 2013

In this study, the characteristics of particle crash of decomposed granite soil sampled at Pocheon area were presented. The degree of weathering was artificially achieved by means of hydrofluoric acid. Weathering index was firstly determined by the analysis of mineral composition. Then, particle distribution, permeability tests were conducted. The results showed that weathering effects on particle crash over entire particle sizes. Comparative analysis on specific surface between $D_{10}$ and $D_{50}$ indicated that the smaller the particle size, the more the particle crash. In addition, the most particle crashing due to compaction appeared around the optimum moisture content. The incremental ratio of specific surface appeared to decrease as weathering proceeds, which means that the higher the weathering index the less the particle crash.

• Journal of the Korea Furniture Society
• /
• v.28 no.3
• /
• pp.248-258
• /
• 2017

A study was carried out to observe the 1% aqueous safranine solution flow speed in longitudinal and radial directions of softwood Thuja orientalis L., diffuse-porous wood Gmelina arborea Roxb., and ring-porous wood Phellodendron amurense Rupr., Longitudinal flow was considered from bottom to top while the radial flow was considered from bark to pith directions. In radial direction, ray cells and in longitudinal direction tracheids, vessel and wood fiber were considered for the measurement of liquid penetration speed at less than 12% moisture contents(MC). The variation of penetration speed for different species was observed and the reasons behind for this variation were explored. The highest radial penetration depth was found in ray parenchyma of T. orientalis but the lowest one was found in ray parenchyma of P. amurense. The average liquid penetration depth in longitudinal trachied of T. orientalis was found the highest among all the other cells. The penetration depth in fiber of G. arborea was found the lowest among the other longitudinal cells. It was found that cell dimension and also meniscus angle of safranine solution with cell walls were the prime factors for the variation of liquid flow speed in wood. Vessel was found to facilitate prime role in longitudinal penetration for hardwood species. The penetration depth in vessel of G. arborea was found highest among all vessels. Anatomical features like ray parenchyma cell length and diameter, end-wall pits number were found also responsible fluid flow differences. Initially liquid penetration speed was high and the nit gradually decreased in an uneven rate. Liquid flow was captured via video and the penetration depths in those cells were measured. It was found that even in presence of abundant rays in hardwood species, penetration depth of liquid in radial direction of softwood species was found high. Herein the ray length, lumen area, end wall pit diameter determined the radial permeability. On the other hand, vessel and fiber structure affected the longitudinal flow of liquids. Following a go-stop-go cycle, the penetration speed of a liquid decreased over time.

• Journal of the Korean Geographical Society
• /
• v.38 no.6
• /
• pp.935-948
• /
• 2003

The State Soil Geographic (STATSGO) database is a valuable source for assessment of soil properties at a state level. Using GIS techniques, eight physical soil properties were extracted from the database, including available water capacity, clay content, soil depth, slope, depth to water table, drainage, texture, and permeability. The influences of these soil properties on drought severity, which was estimated by NDVI departures from normal, were determined over western-central Kansas. Study results showed that seven soil properties had significant relationships with drought severity with correlation coefficients, ranging from -0.89 to 0.85. Thermal emission signals from the Moderate Resolution Imaging Spectroradiometer (MODIS) had a significant relationship with drought severity expressed by NDVI departure from normal and represented spatial progression of drought over time well. High thermal signals, indicating high soil moisture deficit, emerged in the western region and their spatial distribution changed over time. Different sets of soil factors influenced drought severity among early-drying and late-drying areas.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.195-200
• /
• 2005

For the longevity of OLEDs, passivation of OLEDs is an important process step since organic materials used in OLEDs are very vulnerable to moisture. In this work, the passivation effect of the plasma polymerized para-xylene (PP$\rho$X) layers was studied. The PPpX layers deposited by PECVD were formed on top of the cathode with various plasma powers of 50 - 90 W. Passivation effect of PP$\rho$X was significantly dependent upon the deposition plasma power of the PP$\rho$X film. The lifetime of OLEDs with the 70 W deposited PP$\rho$X passivation layer was about 5 times longer than that of the control device.

• Fashion & Textile Research Journal
• /
• v.21 no.2
• /
• pp.203-208
• /
• 2019

This paper considers the moisture permeability and fashion in the upper fabrics of cotton fabric shoes woven into various tissues and properties measured to examine the use as upper fabrics. We measured the tissues of the manufactured upper fabric are 1/3 twill, $4{\times}4$ weft rib, Maya, Triple, Deformed twill design (DTD), Diamond tissues and tear strength, tensile strength, breaking elongation, stretching under load at 100N, stitch tear resistance, and fastness. In the case of $4{\times}4$ weft rib, the tear strength and tensile strength were excellent; however, the elongation and stitch tear resistance at 100N load were less than the standard value. DTD fabrics are characterized by physical properties in the warp direction that are superior to those in the weft direction; however, the tear strength and tensile strength in the weft direction are less than the standard value. The 1/3 twill fabrics showed high tensile strength value and stitch tear resistance value in the warp direction; however, toughness, the main property of the shoe upper, was below the standard value. Triple and diamond fabrics, which have a significant effect on the performance of the shoe upper fabric, also had less than the standard value of tear strength. Maya upper fabric for shoes has better properties than other upper fabrics except for the elongation at break, and the stitch tear resistance has a value of 178% in the warp direction and 214% in the weft direction compared to the standard value. Therefore, the Maya fabric showed the possibility of being used as an upper textile for shoes.

• Computers and Concrete
• /
• v.27 no.3
• /
• pp.241-252
• /
• 2021

An experimental program was conducted to investigate the fresh properties, mechanical properties and durability characteristics of the self-compacting mortars (SCM) produced with pumice powder and Artificial Lightweight Fine Aggregate (aLWFA). aLWFA was produced by using fly ash. A total of 16 different mixtures were designed with a constant water-binder ratio of 0.37, in which natural sands were partially replaced with aLWFA and pumice powder at different volume fractions of 5%, 10% and 15%. The artificial lightweight aggregates used in this study were manufactured through cold bonding pelletisation of 90% of class-F fly ash and 10% of Portland cement in a tilted pan with an ambient temperature and moisture content. Flowability tests were conducted on the fresh mortar mixtures beforehand, to determine the self-compacting characteristics on the basis of EFNARC. To determine the conformity of the fresh mortar characteristics with the standards, mini-slump and mini-V-funnel tests were carried out. Hardened state tests were conducted after 7, 28 and 56 days to determine the flexural strength and axial compressive strength respectively. Durability, sorptivity, permeability and density tests were conducted at the end of 28 days of curing time. The test results showed that the pumice powder replacement improved both the fresh state and the hardened state characteristics of the mortar and the optimum mixture ratio was determined as 15%, considering other studies in the literature. In the aLWFA mixtures used, the mechanical and durability characteristics of the modified compositions were very close to the control mixture. It is concluded in this study that mixtures with pumice powder replacement eliminated the negative effects of the aLWFA in the mortars and made a positive contribution.

• Journal of Environmental Science International
• /
• v.33 no.1
• /
• pp.17-25
• /
• 2024

This study aimed to determine the most suitable coir substrate mixing ratio for optimizing the growth and yield of the "lpduelkkae 1" cultivar. We comprehensively analyzed the physicochemical properties, growth, and yields of four different substrate combinations: perlite (coir with mixing ratios of 70:30 (PC30), 50:50 (PC50), and 30:70 (PC70)) and 100% coir (C100). The results revealed substantial differences in substrate properties. C100 exhibited the highest total porosity and the lowest solid phase, indicating excellent air permeability. The pH levels and electrical conductivity (EC) values ranged from 5.4-6.8 and 1.2-3.1 dS·m^-1, respectively. Leaf growth parameters, including length, width, and dry weight, showed positive correlations with high coir ratios, except for PC30. PC70 and C100 outperformed other substrates in stem growth, exhibiting superior stem diameter and fresh and dry weights. The quantity of marketable leaves was the highest in the C100 substrate. Furthermore, C100 comprised integrated levels of essential nutrients, such as Ca and Mg, owing to its high coir content. In conclusion, a coir ratio of approximately 70% (v/v) should be maintained in the substrate for creating an optimal cultivation environment. Furthermore, the selection of humidity-resistant varieties as well as precise nutrient and moisture management for different seasons and growth stages are crucial for a successful perilla leaf hydroponic cultivation.