• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 춘계학술대회 논문집
• /
• pp.437-441
• /
• 2004

Recently, as the power capability of satellites increase, we need to develop a new SAR(Solar Array Regulator) with much higher power capacity whenever we design a power system of a new satelite. In this case, modular design method could be a good solution for this kind of problem. But when we use a modular method in the design of the parallelled converter, it is very important to share current equally between each module connected in paralled. In this paper, we study how to design the optimum current control-loop and voltage control-loop when we apply average current-mode control method to the parallel SAR. With the design results, we make a protype of the 3-module paralleling SAR and verify its performances.

• 디자인학연구
• /
• 제17권4호
• /
• pp.401-404
• /
• 2004

본 논문은 일반적인 창문의 개념을 혁신적으로 변화시킨 D.I.Y. 목재 창문 시스템 개발에 간한 것이다. 사용자의 필요에 따라 주문 제작이 가능한 D.I.Y. 시스템을 기본으로 다양한 사물의 속성을 나무 프레임을 가진 창과 결합하여, 채광과 환기를 위한 창의 기본적인 기능을 유지하면서 동시에 새로운 심미성을 가진 미래지향적 창 디자인이다. 제한된 규모와 형태 내에서도 사용자의 필요에 의하여 공간의 효율성 증대 및 다양한 기능을 수용할 수 있는 가능성을 제공하여 안에서나 밖에서나 즐거운 시각으로 창을 바라보게 한다. 또한 나무 플임은 모듈로 되어 있으므로 가변성을 고려한 규격화된 부품을 카탈로그와 연계하여 대량 생산 할 수 있는 가능성을 지니고 있다. 미래의 창문은 보기위한 중간매개체 역할 뿐 아니라, 미래지향적인 창의 디자인과 기술을 재정립하여 사용자 스스로 기본 요소들을 조합하고 분리하여 수납공간, 생활 가구 등의 기능이 활용된 개성 있는 Window를 연출 할 수 있는 것이다.

• 복식문화연구
• /
• 제22권5호
• /
• pp.776-793
• /
• 2014

This study attempted to figure out the usage of the modular system in other fields through literature review and empirical study, analyze its structural method in fashion. After analyzing architecture & product-related books, the Internet data and previous studies, the modular system's five structural methods were obtained. Then, 991 photos of women's clothes from 2003 to 2014 were collected through the fashion websites in Korea and abroad. The results can be summarized as follows: First, the following five structures were derived: assembling structure, overlapping structure, arrangement structure, inserting structure and folding structure. Second, according to analysis on the structural method of the modular system in modern fashion, overlapping structure (34%) was the most common. Third, in fashion, the use of fastener for installation and removal is important for assembling structure. In terms of overlapping structure, 3D volume by vertical accumulation was commonly observed. Arrangement structure revealed a horizontal and flat shape through simple arrangement. In inserting structure, on the contrary, non-standardized modules were used as a part of clothes or decorative elements. In folding structure, origami technique for reduction and expansion was used.

• 한국의류학회지
• /
• 제32권5호
• /
• pp.788-799
• /
• 2008

Since the late 20C, a lot of fashion designers have considered about new construction system in fashion. Many arguments about architectural form and construction system have being supported on enlargement of range of functionalism fashion through the consideration about new shape and combination among various any other spheres. Modular concept, which is able to divide complex construction of integration into separated basic unit and use various and liberal arrangements, is regarded alternative idea of economic construction that creates new shape and constructive beauty through the simple operation and changing combination continuously. Specially, fashion designs of Yoehlee Teng, John Ribber, and Galya Rosenfeld are estimated that they are effectively utilized architectural modular system pursuing multi-function and multi-change in fashion. Modular system utilized in fashion construction will be classified as follows: 1) layering system of Yoehlee Teng, 2) combine system of john Ribber, and 3) lego system of Galya Rosenfeld. This thesis will presents beneficial guide for simple and practical functionalism fashion design development in 21C.

• Steel and Composite Structures
• /
• 제31권3호
• /
• pp.217-232
• /
• 2019

Modular steel buildings consist of prefabricated room-sized structural units that are manufactured offsite and installed onsite. The inter-module connections must fulfill the assembly construction requirements and soundly transfer the external loads. This work proposes an innovative assembled connection suitable for modular buildings with concrete-filled steel tube columns. The connection uses pretensioned strands and plugin bars to vertically connect the adjacent modular columns. The moment-transferring performance of this inter-module connection was studied through monotonic and cyclic loading tests. The results showed that because of the assembly construction, the connected sections were separated under lateral bending, and the prestressed inter-module connection performed as a weak semirigid connection. The moment strength at the early loading stage originated primarily from the contact bonding mechanism with the infilled concrete, and the postyield strength depended mainly on the tensioned strands. The connection displayed a self-centering-like behavior that the induced deformation was reversed during unloading. The energy dissipation originated primarily from frictional slipping of the plugin bars and steel strands. The moment transferring ability was closely related to the section dimension and the arrangements of the plugin bars and steel strands. A simplified strength calculation and evaluation method was also proposed, and the effectiveness was validated with the test data.

• Nuclear Engineering and Technology
• /
• 제54권4호
• /
• pp.1526-1533
• /
• 2022

Small modular reactors have garnered considerable attention in the recent years. Plate fuel elements exhibit a good application prospect in small modular pressurized water reactors for marine applications. Further, improved economic benefits can be achieved by extending the core lifetime of small modular reactors. However, it is necessary to realize a large initial residual reactivity for achieving a relatively long burnup depth finally. Thus, the selection of a suitable burnable poison (BP) is a crucial factor that should be considered in the design of small modular reactors. In this study, some candidate BPs are selected to realize the effective control of reactivity. The results show that ²³¹Pa₂O₃, ²⁴⁰Pu₂O₃, ¹⁶⁷Er₂O₃, PACS-J, and PACS-L are ideal candidates of BP, and since the characteristics of BP can increase the final burnup depth of assembly, the economic benefits are gained. Additionally, an optimal combination scheme of BPs is established. Specifically, it is proved that through a reasonable combination of BPs, a low reactivity fluctuation during the lifetime can be achieved, leading to a large final burnup depth.

• Steel and Composite Structures
• /
• 제48권3호
• /
• pp.321-333
• /
• 2023

This paper proposes a comprehensive investigation on lateral stiffness of corner-supported steel modular frame using splice connection. A full-scale modular frame with two stacked steel modules under lateral load is tested. Ductile pattern in the transfer of lateral load is found in the final failure mode. Two types of lateral stiffness, including tangent stiffness and secant stiffness, are defined from the load-displacement due to the observed nonlinearity. The difference between these two types of stiffness is found around 20%. The comparisons between the experimental lateral stiffness and the predictions of classical methods are also conducted. The D-value method using hypothesis of independent case is a conservative option for predicting lateral stiffness, which is more recommended than method of contraflexural bending moment. Analyses on two classical short-rod models, including fix-rod model and pin-rod model, are further conducted. Results indicate that fix-rod model is more recommended than pin-rod model to simplify splice connection for simulation on lateral stiffness of modular frame in elastic design stage.

• 국제학술발표논문집
• /
• The 9th International Conference on Construction Engineering and Project Management
• /
• pp.536-542
• /
• 2022

Cost overruns, schedule delays, and a shortage of skilled labor are common problems the construction industry is currently experiencing. Modularization and standardization strategies have the potential to resolve the various problems mentioned above and have been applied for various construction applications for a long time. However, the level of modularization remains low, and modular construction projects have not been getting the full benefits. Thus, this review investigated the cutting-edge technologies currently being utilized to develop the modular construction field. For this paper, qualified research papers were identified using predetermined keywords from previous related research papers. Identified literature was then filtered and analyzed. According to the included reviews, several technologies are being developed for modular construction. For example, automated design and monitoring systems for modularization were developed. In addition, research labs are utilizing robotic arms for modular construction to achieve a high level of completion in the construction industry, as is seen in the manufacturing industry. Despite these efforts, more research and development are necessary because some automation technologies still require manual activities. Thus, there is great potential for further development of modularization techniques, and further research is recommended to achieve high levels of modularization.

• 국제학술발표논문집
• /
• The 9th International Conference on Construction Engineering and Project Management
• /
• pp.543-550
• /
• 2022

The U.S. Department of Energy conducts the Solar Decathlon competition as a student-based achievement that encourages sustainable design with energy efficiency and solar energy technologies. In the 2020 competition, the University of Nevada, Las Vegas (UNLV) team designed, fabricated, and constructed a net-zero modular house that applies innovative and highly efficient building technologies. This paper focused on the lessons learned during the early phases of this ongoing modular project. The research methodology included obtaining feedback from key project participants using a well-structured questionnaire. The results showed that the major items/challenges in the project's planning phase included selecting the modular size, planning the construction system, planning the materials and procurement, estimating costs and duration, selecting a fabricator, collaboration and communication, safety, and planning module transportation. These findings will help modular practitioners and future Solar Decathlon competition participants better understand how and what factors they should consider most during the early phases through the lessons learned.

• 한국경영과학회:학술대회논문집
• /
• 대한산업공학회/한국경영과학회 2002년도 춘계공동학술대회
• /
• pp.625-631
• /
• 2002

A module design aims to develop product architecture that consists physically detachable units such as module. To develop the system of module design, this paper suggests the methodology of part grouping, evaluation of modularization of a product for improving modularization. To determine modules, module concept is proposed to satisfy the objectives of a modular design. Therefore, there are functional, structural, and process modularizations in a modular concept. Module grouping can be accomplished by using an optimization model that maximizes the sum of the weighting. The present study proposes the p-median model and the direct clustering technique. The optimal clustering solution can be obtained by comparing two clustering techniques. To find the best solution among part groups, evaluation of modularization is performed based on the concept of module design. For the evaluation of modularization, evaluation criteria of modularization are used in the matrix table.