• International Journal of Highway Engineering
• /
• v.17 no.3
• /
• pp.27-33
• /
• 2015

PURPOSES : To ensure appropriate RCC properties with sufficient strength development and workability, it is necessary to secure a proper level of consistency. It is also necessary to secure maximum dry density, which is an important factor for increasing the interaction of aggregate interlocking, leading to an augmentation of RCC strength. On the other hand, the dry density of RCC can be changed owing to the compaction conditions, water content, and particle size distribution. A Proctor test and a modified Proctor test were used for determining the optimum water content needed to achieve maximum dry density with different amounts of compaction energy. A Vebe test, on the other hand, was used for checking the level of consistency, which is important for producing a workable mixture. METHODS : To confirm the degree of compaction at various particle sizes, RCC mixtures with different sand/aggregate ratios were evaluated. The Proctor test and modified Proctor test were applied to these mixtures to check the effect of the aggregate gradation and compaction energy on the maximum dry density and optimum water content. During each test, three specimens were produced for all types of water content under each aggregate gradation. A compaction curve and the optimum water content and maximum dry density for each aggregate gradation were then obtained for both tests. The range of water content for the appropriate consistency of each aggregate gradation was determined through a Vebe test. The optimum water content was then evaluated based on this range. RESULTS : The compaction test results show that the modified Proctor test provides a higher maximum dry density and lower optimum water content compared with the standard Proctor test. For the modified Proctor test, two cases of aggregate gradation (s/a = 30% and 70%) had the optimum water contents outside of the appropriate water content range. For the standard Proctor test, on the other hand, none of aggregate gradations provided the optimum water content within the desired range. CONCLUSIONS : The modified Proctor test should be used for an RCC mixture design because it can provide adequacy between maximum dry density and consistency. Moreover, the compaction roller has become highly developed for higher compaction energy.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.4
• /
• pp.931-940
• /
• 2015

Roller Compacted Concrete Pavement (RCCP), is a type of pavement using compaction roller and asphalt finisher on concrete mixture that contains low amount of water. RCCP strength and durability are greatly affected by compaction level. Quality control is performed by ensuring the degree of compaction at site based on dry density. In the field, Modified Proctor Test is used in order to obtain optimum dry density. However, there is no clear compaction curve analysis criteria of Modified Proctor Test for RCCP. In this study, compaction curve built by three samples of Modified Proctor Test was produced and it was used to compare with compaction curve contented lower number of samples (one and two samples) in order to analyze their reliability. Thus, a conclusion was drawn from the results; by comparing to the result from Modified Proctor Test of three samples, the use of two samples represented result with only 0.5% of error which means the reliability is 99.5%.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.23 no.3
• /
• pp.65-77
• /
• 1981

The Compaction of fill dam is very important for increasing of the safty of dam. Vibration roller is used for the compaction of pervious materials such as sand and gravel. The principal objects of this study are to give a comstruction criteria of vibration roller and to find out the relationship between dry density and permeabity of pervious soil after compaction. The results in this study are summerized as follows. 1.The relationship between maximum dry density (Υdmax) and optimum moisture content(Wo) of modified compaction test is Υdmax=2. 74-0. 064w0 2.The maximum dry density decrease with increasing fine particle(n) and the relative formular is n==ae-brdmax 3.The maximum dry density is influenced more by passing rate of number 200 sieve than 4 sieve. 4.The coefficient of permeability are similar when the degrees of compaction are equal even though the spreading thickness of soil are different. 5.The coefficient of permeability(K)is greatly influence by fine particle passing number 200 sieve, and those relationship is inversely proportionate. 6.The K values of pervious soil are from 10-0 cm/sec to 10-4 cm/sec when degree of compaction by a modified method is from 90 to 95percent. 7.The coarser material is little influenced on the permeability with different density. 8.The increasing rate of permeability with decreasing degree of compaction is more influened by fine pacticle than number 200 sieve. When degree of compaction decrease from 100 percent to 90 percent the K values of SM and GM increase about 20 times but GW increase 6 times only. 9.The effect of compaction by vibration roller is greatly influenced by 6 passes and the increasing rate of the effect is decraased at 8 passes. 10. In order to get the degree of compaction of 95 percent or more, 6 to 8 passes of roller are generall required with 30 cm thickeness of soil for 4.5 ton to 6.5 ton vibration roller and 7 to 8 passes is required with 50cm thickness for 8 to 12 ton roller.

• Transactions of Materials Processing
• /
• v.21 no.4
• /
• pp.228-233
• /
• 2012

In this study, powder compaction of AZO (alumina doped zinc oxide) powder was performed with a MTS 810 test system using a cylindrical die having a diameter of 10mm. Pressure-density curves were measured based on the load cell and displacement of the punch. The AZO powder compacts with various densities were formed to investigate the mechanical properties such as fracture stress of the AZO powder as a function of the compact density. Two types of compression tests were conducted in order to estimate the fracture stress using different loading paths: a diameteral compression test and a uniaxial compression test. The pressure-density curves of the AZO powder were obtained and the fracture stress of the compacted powders with various densities was estimated. The results show that the compact pressure dramatically increases as the density increases. Based on the experimental results, calibration of the modified Drucker-Prager/Cap model of the AZO powder for use in FE simulations was developed.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.12
• /
• pp.105-113
• /
• 2018

In this study, the engineering properties including bearing capacity of subgrades stabilized with a binder are analyzed by laboratory and field experiments. The main components of the binder are CaO and $SO_3$. After the binder was mixed with a low plasticity clay, the passing rates were relatively decreased as the sieve mesh size increased. Not only did the soil type change to silty sand, but engineering properties, such as the plasticity index and modified California bearing ratio (CBR), were improved for the subgrade. A comparison of the compaction curves of the stabilized subgrade and field soil compacted with the same energy demonstrated an increase of approximately 6% in the maximum dry unit weight, slight decrease in optimum moisture content, and considerable increase improvement in grain size. In the modified CBR test, the effect of unit weight and strength increase of the modified soil (with a specific amount of binder) was remarkably improved. As the proportion of granulated material increased after the addition of binder, the swelling was reduced by 3.3 times or more during initial compaction and 6.5 times by final compaction. The unconfined compressive strength of the specimens was maintained at the homogeneous value with a constant design strength. The stabilized subgrade was validated by applying it in the field under the same conditions; this test demonstrated that the bearing capacity coefficients at all six sites after one day of compaction exceeded the target value and exhibited good variability.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.974-981
• /
• 2005

Because general laboratory tests for sand compaction pile method including unit-cell test device have fixed outside diameter, as area replacement ratio increase, diameter of sand pile increase. These condition can bring about overestimation of stiffness of composite ground. In addition, existing large soil box which consist of bellows type loading plate can occur serious mistake in checking the amount of drained water because there are additional drainage along the inside wall in device. Overcoming these shortcoming, this paper developed modified large scale soil box consist of piston type load plate. In this study, using this device, series of modified large scale soil box tests were performed, and investigated the settlement and stress transportation characteristics with area replacement ratio in sand compaction pile method.

• International Journal of Railway
• /
• v.1 no.2
• /
• pp.64-71
• /
• 2008

The quality of track-bed fills of railways has been controlled by field measurements of density $({\gamma}_d)$ and the results of plate-load tests. The control measures are compatible with the design procedures whose design parameter is $k_{30}$ for both ordinary-speed railways and high-speed railways. However, one of fatal flaws of the design procedures that there are no simple laboratory measurement procedures for the design parameters ($k_{30}$ or, $E_{v2}$ and $E_{v2}/E_{v1}$) in design stage. A new quality control procedure, in parallel with the advent of the new design procedure, is being proposed. This procedure is based upon P-wave velocity involving consistently the evaluation of design parameters in design stage and the field measurements during construction. The Key concept of the procedure is that the target value for field compaction control is the P-wave velocity determined at OMC using modified compaction test, and direct-arrival method is used for the field measurements during construction. The procedure was verified at a test site and the p-wave velocity turned out to be an excellent control measure. The specifications for the control also include field compaction water content of OMC${\pm}$2% as well as the p-wave velocity.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1427-1439
• /
• 2008

The quality of track-bed fills of railways has been controlled by field measurements of density (${\gamma}_d$) and the results of plate-load tests. The control measures are compatible with the design procedures whose design parameter is $k_{30}$ for both ordinary-speed railways and high-speed railways. However, one of fatal flaws of the design procedures is that there are no simple laboratory measurement procedures for the design parameters ($k_{30}$ or, $E_{v2}$ and $E_{v2}/E_{v1}$) in design stage. A new quality control procedure, in parallel with the advent of the new design procedure, is being proposed. This procedure is based upon P-wave velocity involving consistently the evaluation of design parameters in design stage and the field measurements during construction. The key concept of the procedure is that the target value for field compaction control is the P-wave velocity determined at OMC using modified compaction test, and direct-arrival method is used for the field measurements during construction. The procedure was verified at a test site and the p-wave velocity turned out to be an excellent control measure. The specifications for the control also include field compaction water content of $OMC{\pm}2%$ as well as the p-wave velocity.

• Journal of Industrial Technology
• /
• v.22 no.B
• /
• pp.211-218
• /
• 2002

The paper is to show the behavior of composit ground which is installed with sheet pile in soft soil improved by sand compaction pile. The results of load-settlement relationship, earth pressure, stress concentration characteristics, and final water content were obtained by centrifuge model test. Two cases of tests, installation of sheet pile on the corner and both side of the loading plate for the improved SCP ground which was designed twice of the footing width, were performed for the tests under the vertical and horizontal loading and both side of corner. Finite element program(CRISP) for sand compaction pile using elasto-plastic model and numerical analysis for soft soil using modified cam-clay constitutive equation were compared and analized with the results of model tests. The result of analysis show the increased bearing capacity of soil after, SCP and sheet pile was installed.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.127-132
• /
• 2009

This study presents the test results on the compaction characteristics of warm mix asphalt mixtures that include the additive in 3 different mixtures(hot mix asphalt, SBS and SMA). The tests were conducted to find out the compaction characteristics on the compactability with varying compaction time, different amount of the warm mix additive and lowering the compaction temperature. The Superpave gyratory compactor was used to find out the variation of the density when the number of the gyration is varied. A dense mixture and 3 different warm mix additives were employed to find the relationship between compactability and compaction time. The comparison of the compactability with lowering the temperature was conducted using dense mixture, SBS polymer modified mixture and stone matrix asphalt mixture(SMA). The difference of the density of warm mix asphalt mixtures was not found due to the lowering of compaction temperature when it was compared with the standard mixture and the warm mix showed the stable condition in density. In the mean time, depending upon the different warm mix additive and mixture, the difference of density and the variation trend of compaction is found to be existed and shows the relationship between these two variables.