• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.4
• /
• pp.15-22
• /
• 2012

This paper deals with the performance comparison and evaluation of blind adaptive equalizer, the PMCMA-MDD and DW-MCMA, that is used for compensation of the amplitude and phase distortion which occurs in the time dispersive channel. Basically, these algorithms are modification of MCMA cost function in order to obtain the fast convergence speed and reduced residual isi by taking the parallel and serial double structured and the combination of the concept of RCA for the updating the tap coefficient. We implements the algorithm of it and compare the recovered constellation, residual isi, MSE characteristics curve and SER in the signal to noise ratio given the time dispersive channel. As a result of simulation, the PMCMA-MDD has a good in recovered constellation than DW-MCMA. But in the SER, the DW-MCMA has a good than PMCMA-MDD.

• Journal of the Korean Data and Information Science Society
• /
• v.23 no.1
• /
• pp.89-98
• /
• 2012

In this paper, the ratio of parameters in two independent Maxwell distributions is parameter of interest. We proposed test statistics, which converge to standard normal distribution, based on likelihood function. The exact distribution for testing the ratio is hard to obtain. We proposed the signed log-likelihood ratio statistic and the modified signed log-likelihood ratio statistic for testing the ratio. Through simulation, we show that the modified signed log-likelihood ratio statistic converges faster than signed log-likelihood ratio statistic to standard normal distribution. We compare two statistics in terms of type I error and power. We give an example using real data.

• International Journal of Computer Science & Network Security
• /
• v.23 no.7
• /
• pp.1-8
• /
• 2023

An Orthogonal Frequency Division Multiplexing (OFDM) based wireless communication system has drawn wide attention for its high transmission rate and high spectrum efficiency in not only radio but also Underwater Acoustic (UWA) applications. Because of the narrow sub-carrier spacing of OFDM, orthogonality between sub-carriers is easily affected by Doppler effect caused by the movement of transmitter or receiver. Previously, Doppler compensation signal processing algorithm for Desired propagation path was proposed. However, other Doppler shifts caused by delayed Undesired signal arriving from different directions cannot be perfectly compensated. Then Receiver Bit Error Rate (BER) is degraded by Inter-Carrier-Interference (ICI) caused in the case of Multi-path Doppler channel. To mitigate the ICI effect, a modified Delay and Doppler Profiler (mDDP), which estimates not only attenuation, relative delay and Doppler shift but also sampling clock shift of each multi-path component, is proposed. Based on the outputs of mDDP, an ICI canceling multi-tap equalizer is also proposed. Computer simulated performances of one-tap equalizer with the conventional Time domain linear interpolated Channel Transfer Function (CTF) estimator, multi-tap equalizer based on mDDP are compared. According to the simulation results, BER improvement has been observed. Especially, in the condition of 16QAM modulation, transmitting vessel speed of 6m/s, two-path multipath channel with direct path and ocean surface reflection path; more than one order of magnitude BER reduction has been observed at CNR=30dB.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.5
• /
• pp.552-560
• /
• 2013

In this paper, an optimization algorithm for the block assembly accuracy control assessment is proposed with consideration for the current block assembly process and accuracy control procedure used in the shipbuilding site. The objective function of the proposed algorithm consists of root mean square error of the distances between design and measured data of the other control points with respect to a specific point of the whole control points. The control points are divided into two groups: points on the control line and the other points. The grouped data are used as criteria for determining the combination of 6 degrees of freedom in the registration process when constituting constraints and calculating objective function. The optimization algorithm is developed by using combination of the sampling method and the point to point relation based modified ICP algorithm which has an allowable error check procedure that makes sure that error between design and measured point is under allowable error. According to the results from the application of the proposed algorithm with the design and measured data of two blocks data which are verified and validated by an expert in the shipbuilding site, it implies that the choice of whole control points as target points for the accuracy calculation shows better results than that of the control points on the control line as target points for the accuracy of the calculation and the best optimized result can be acquired from the accuracy calculation with a fixed point on the control line as the reference point of the registration.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.12
• /
• pp.91-97
• /
• 2000

With the brilliant development of information communication and the rapid spread of internet, current network communication is carrying several up-to-date functions such as electronic commerce, activation of electro currency or electronic signature and will produce more advanced services in the future. Information communication network such as that electronic commerce would demand the more safe and transparent guard of network, and anticipate the more fast performance of network. In this paper, in order to meet the several demands, DES(data encryption standard) with parallel feistel structure, which feistel structure of the basic structure of DES is transformed into in parallel, is proposed. The existing feistel structure can't use pipeline method for the structural problem of DES itself-the propagation of error. therefore, this modified parallel feistel structure could improve largely the performance of DES which had to have the trade-off relation between data processing speed and data security and in addition a method proposed in SEED having adopted the modified parallel feistel structure shows more excellent secure function and/or fast processing ability. The used CAD Tool use Synopsys Ver. 1999. 10 in both of synthesis and simulation.

• Journal of Korea Water Resources Association
• /
• v.35 no.1
• /
• pp.1-12
• /
• 2002

This study was intended to investigate the rainfall-runoff relationship with spatially distributed rainfall data, and then, to analyze and quantify the uncertainty induced by spatially averaging rainfall data. For constructing spatially distributed rainfall data, several historical rainfall events were extended spatially by simple kriging method based on the semivariogram as a function of the relative distance. Runoff was computed by two models; one was the modified Clark model with spatially distributed rainfall data and the other was the conventional Clark model with spatially averaged rainfall data. Rainfall errors and discharge errors occurred through this process were defined and analyzed with respect to various rain-gage network densities. The following conclusions were derived as the results of this work; 1) The conventional Clark parameters could be appropriate for translating spatially distributed rainfall data. 2) The parameters estimated by the modified Clark model are more stable than those of the conventional Clark model. 3) Rainfall and discharge errors are shown to be reduced exponentially as the density of rain-gage network is increased. 4) It was found that discharge errors were affected largely by rainfall errors as the rain-gage network density was small.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.4
• /
• pp.137-143
• /
• 2010

This paper deals with the performance comparison of self adaptive equalizer by the weighting factor of MCMA cost function for the compensate the amplitude and phase distortion which occurs in the communication channel. The MCMA is improves the cost function of present CMA at the output of equalizer for the minimize of error function in the amplitude and phase, the value of weighting factor is used at this time. When the comparison of equalizer performance, we classified to initial state and steady state, then it represents the convergence time and convergence speed and steady state operation of equalizer to the predetermined level, it is determined by the weighting factor. We confirm to the different result to this 2 state by weighting factor values using computer simulation. By using the result of this paper, if we appropriately choose the weighting factor values in the environment of communication channel, it is expected that the high quality digital transmission is possible.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.816-819
• /
• 2005

This paper proposes a coordinate correction technique using the transformation of 3D parabolic coordinate function and BP(Back Propagation) neural network in order to solve space distortion problem caused by using catadioptric camera. Although Catadioptric camera can obtain omni-directional image at all directions of 360 degrees, it makes an image distorted because of an external form of lens itself. Accordingly, To obtain transformed ideal distance coordinate information from distorted image on 3 dimensional space, we use coordinate transformation function that uses coordinates of a focus at mirror in the shape of parabolic plane and another one which projected into the shape of parabolic from input image. An error of this course is modified by BP neural network algorithm.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.621-632
• /
• 2007

The purpose of this study was the estimation and formulation of orthotropic flexural rigidities considering the deformed shape for a plate stiffened with rectangular ribs. Analytical results of methods modifying the flexural rigidity of the x-direction, the y-direction or both directions were compared at the center, the x-directional quarter point and the y-directional quarter point of stiffened plates loaded at the center. The composite method modifying the flexural rigidity of both directions improves the accuracy compared with the other methods. Moreover, the ratio of modified coefficients for each directional rigidity can be expressed as a function corresponding to each dimension of stiffened plates. The application of modified coefficient functions to various types of stiffened plates with different boundary conditions, aspect ratios and rib arrangement shows that the increment of the error ratio is small compared with examples of this study and the application of proposed functions shows more accurate results than previous methods modifying the flexural rigidity. Therefore, by using the modified coefficient functions proposed in this study, the orthotropic plate analysis of plates stiffened with rectangular ribs can easily achieve more accurate displacement results.

• Journal of Astronomy and Space Sciences
• /
• v.27 no.2
• /
• pp.153-160
• /
• 2010

We modified the optical system of 500 mm wide-field telescope of which point spread function showed an irregularity. The telescope has been operated for Near Earth Space Survey (NESS) located at Siding Spring Observatory (SSO) in Australia, and the optical system was brought back to Korea in January 2008. After performing a numerical simulation with the tested value of surface figure error of the primary mirror using optical design program, we found that the surface figure error of the mirror should be fabricated less than root mean square (RMS) $\lambda$/10 in order to obtain a stellar full width at half maximum (FWHM) below $28\;{\mu}m$. However, we started to figure the mirror for the target value of RMS $\lambda$/20, because system surface figure error would be increased by the error induced by the optical axis adjustment, mirror cell installation, and others. The radius of curvature of the primary mirror was 1,946 mm after the correction. Its measured surface figure error was less than RMS $\lambda$/20 on the table of polishing machine, and RMS $\lambda$/15 after installation in the primary mirror cell. A test observation performed at Daeduk Observatory at Korea Astronomy and Space Science Institute by utilizing the exiting mount, and resulted in $39.8\;{\mu}m$ of stellar FWHM. It was larger than the value from numerical simulation, and showed wing-shaped stellar image. It turned out that the measured-curvature of the secondary mirror, 1,820 mm, was not the same as the designed one, 1,795.977 mm. We fabricated the secondary mirror to the designed value, and finally obtained a stellar FWHM of $27\;{\mu}m$ after re-installation of the optical system into SSO NESS Observatory in Australia.