• 한국농공학회지
• /
• 제45권5호
• /
• pp.110-116
• /
• 2003

A catchment modelling system is the summation of the numerous hydrologic, hydraulic and other process models necessary to simulate the response of a catchment to a storm event. Differences between the recorded catchment response and that predicted by a catchment modelling system can arise from structural errors within the catchment modelling system, evaluation errors in the control parameters, or measurement errors in the recorded data being used to assess the reliability of the evaluation of the control parameters. Presented herein is an investigation of the potential measurement errors within the recorded information, which was considered to occur from instrument error in the ultra sonic flow monitor. This investigation was undertaken using three available rating curves at the Musgrave Avenue Stormwater System in Centennial Park, Sydney, developed by Abustan (1997), Water Board (1994), and using Manning's equation.

• 해양환경안전학회지
• /
• 제5권1호
• /
• pp.9-18
• /
• 1999

To predict the oil spill dispersion phenomena in the ocean, the oil spill response model, which can be used for strategic purpose on the oil spill site, based on Lagrangian particle-tracking method was formulated and applied to the neighboring area with Pusan port where the oil spill incident occurred when the tanker ship No.1 Youil struck on a small rock near the Namhyungjeto on September 21, 1995. The real-time tidal currents to be required as input data of the oil spill model were obtained by the two-dimensional hydrodynamic model and the tide prediction model. Evaluation of tidal currents using observation data was successful. For wind data, other input data of oil spill model, observed data on the spot were used. To verify the oil spill model, the oil spill modelling results were compared with the field data obtained from the spill site. Compared the modelling results with the observation data, there exist some discrepancies but the general pattern of modelling results was similar to that of field observation. The modelling results on 7 days after spill occurred showed that the 40% of spilled oil is in floating, 36% in evaporated, 23% at shore, and 1% in out of boundary, respectively. According to the evaluation of weighting curves of effective components to the dispersion of oil, the winds make a 37% of contribution to the dispersion of oil, turbulent diffusion 39.5%, and tidal currents 23.5%, respectively. Provided the more accurate wind data are supported, more favorable results might be obtained.

• 한국방재안전학회논문집
• /
• 제10권1호
• /
• pp.1-10
• /
• 2017

근래에 들어 증가하고 있는 도심지 지반함몰 사고는 사회적 이슈가 되고 있으며 이로 인해 최근 관련 법안이 발의 되었다. 지반함몰은 수많은 원인인자들의 복합적 작용으로 발생하므로 수치해석적 기법의 적용에 한계점이 존재한다. 이로 인해 지반함몰 메커니즘 규명 연구는 주로 모형실험을 이용하여 진행되었다. 선행 연구들은 상하수도관 파열로 인한 지반함몰 모사에 초점이 맞추어져 있으며, 지하수 흐름, 지반 굴착공사 등 다양한 원인에 의해 발생하는 지반함몰에 대한 연구가 부족한 실정이다. 또한 기존 수행된 대부분의 모형실험은 1 g 상태의 모형실험이며, 지반함몰 메커니즘 평가 시 지반의 현장 구속응력을 고려할 수 없다. 따라서 본 논문에서는 모형실험을 이용한 지반함몰 거동 평가에 대한 선행 연구동향들을 고찰하여 보다 다양한 환경 조건을 모사할 수 있는 기법들에 대해 논의하였다. 또한 본 연구에서는 더 신뢰성이 있는 지반함몰 메커니즘 평가 기법으로서 원심모형실험기법을 제시하였다. 마지막으로 본 연구에서는 지반안정성평가에 지반함몰 메커니즘에서 사용한 모형실험 기법을 적용할 것을 제시했다.

• International Journal of CAD/CAM
• /
• 제3권1_2호
• /
• pp.67-75
• /
• 2003

Viewpoint-dependent feature-based modelling in computer-aided design is developed for the purposes of supporting engineering design representation and automation. The approach of this paper uses a combination of a multi-level modelling approach. This has two stages of mapping between models, and the multi-level model approach is implemented in three-level architecture. Top of this level is a feature-based description for each viewpoint, comprising a combination of form features and other features such as loads and constraints for analysis. The middle level is an executable representation of the feature model. The bottom of this multi-level modelling is a evaluation of a feature-based CAD model obtained by executable feature representations defined in the middle level. The mappings involved in the system comprise firstly, mapping between the top level feature representations associated with different viewpoints, for example for the geometric simplification and addition of boundary conditions associated with moving from a design model to an analysis model, and secondly mapping between the top level and the middle level representations in which the feature model is transformed into the executable representation. Because an executable representation is used as the intermediate layer, the low level evaluation can be active. The example will be implemented with an analysis model which is evaluated and for which results are output. This multi-level modelling approach will be investigated within the framework aimed for the design automation with a feature-based model.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.744-747
• /
• 2001

This paper shows shear wave behavior of CFRP composite laminates as a polar grid form to evaluate vibration pattern of ultrasonic transducers, which gives measured modelling fundamental contents of nondestructive evaluation. Polarized direction can be obtained by using a c-scanner and sensitivity of transducers is founded when using through-transmission method of two transducers. And modelling of vector decomposition is presented based on ply-to-ply method to apply practicable nondestructive evaluation of CFRP laminate lay up. This modelling decomposes the transmission of linearly polarized wave into orthogonal components through each ply of a laminate. It is found that a high provable shows between the model and experimental developed in characterizing layup of CFRP composite laminates.

• 대한치과의사협회지
• /
• 제56권9호
• /
• pp.462-478
• /
• 2018

임플란트와 지대주 간에 허용가능한 적합도를 넘는 부적합을 발견하고 이에 대처하는 것은 중요한 과제이다. 부적합을 임상에서 평가하고 발견하는 방법은 대부분 부적합의 정성적 평가에 치중하고 있으며 술자의 숙련도에 의존하고 있어 정확한 평가방법이라고 하기는 어렵다. 부적합의 정도를 판단하고 원인을 실험적으로 분석하는 방법 중 본 문헌고찰에서는 광탄성 분석법, 유한요소분석법, 스트레인게이지, 미생물 균체 분석 등 조건을 모형화하여 분석하는 모형화법과 사진 측량, 삼차원 좌표 측정, 현미경분석 및 방사선분석을 통해 부적합의 정도를 정밀하게 측정하는 수치법을 각각 설명하고 그 장단점 및 적용의 한계를 분석하였다. 지금까지 살펴본 실험실 부적합 평가 방법들을 장, 단점 및 정확도와 재현성을 기준으로 표로 정리한 것이 Table 3이다. 어떤 방법도 모든 경우에 적용할 수 있을 정도로 완벽하지는 않으므로 평가하고자 하는 부적합의 특성에 따라 적절한 평가방법을 선택하여 적용하는 것이 필요하다고 사료된다.

• 산업기술연구
• /
• 제27권B호
• /
• pp.209-214
• /
• 2007

This paper is the research result about centrifuge model experiments of investigating the behavior of bridge abutment on the sloped ground. Ground condition of the studied site was the bridge abutment with pile foundation adjacent to the slope. The pile foundations was supported on the soft rocks covered with the embankment. Evaluating the behavior of such a complicate ground and structure conditions was not easy so that the centrifuge modelling was performed to find the overall behavior of them. Layout of centrifuge model experiment was simplified to simulate easily the actual behavior of very complicate site condition. Construction process in field such as ground excavation for footing foundation, installation of piles, placement of footing and bridge abutment, backfilling and surcharge loading eas duplicated in the centrifuge model experiment. Consequently, the stability of the piled bridge abutment adjacent to the slope of embankment was evaluated throughout centrifuge modelling.

• 대한안전경영과학회지
• /
• 제6권4호
• /
• pp.227-238
• /
• 2004

This development has tried to scheme out the convenience for users to use the 3D modeling solution which is developed from the existing programs. The extended 3D modeling solution, to be developed through the use of the API which is provided and Microsoft Access, database is able to reuse the parts, subassemblies of parts, and assemblies. A methodology exhibits the possibility to use a Spinfire Professional Spinfire Reader program. The web evaluation system, which is used to connected with the Internet explorer and to construct a web service, will repeat the evaluations of the company staffs and customers about the new products which the company have designed. The furniture manufacturing company will adopt the 3D modelling solution in modelling the new products and go through the web evaluation system to collect dissatisfied facts of the customers or the company staffs against the new product. Finally, it will contribute to the enormous benefit creation of the enterprise.

• 한국공간구조학회논문집
• /
• 제14권2호
• /
• pp.41-50
• /
• 2014

The stone pagoda of Mireuk temple site is currently restoring through the repairing process. This stone pagoda has the various construction types in the inner and outer space. Therefore, the stress concentration and structural behavior need to be considered through the analysis of various construction patterns. To this end, this study presents the structural modelling and analysis considering the discrete element analysis technique to solve the discontinuum behavior between the stone elements. Also, this study performs the structural performance evaluation through the various design variables for the safety of stone pagoda. Through the analysis results, we can find out the small stress concentration in the several members. But, because the stresses and displacements are relatively small, we can secure the safety of the whole structure.

• 대한안전경영과학회지
• /
• 제5권2호
• /
• pp.75-85
• /
• 2003

Manufacturing firms have adapted seriously the Design for Manufacture and Assembly (DFMA) techniques which consider concurrently all factors related to the product development by using effective communications and sharing of information on product development processes. This study performed modelling and characterizing the data related to product manufacturing information for Design for Manufacture(DFM) evaluation and analysis. It adapted component-based development method for communicating and managing manufacturing information among distributed manufacturing organizations. Introducing component-based development offers safety and speed to network based system. This development using Unified Modelling Language(UML) provides efficient way for reconstruction and distribution of applications. Also, the integration of database and component into the internet environment enables to communicate and manage effectively manufacturing information for DFM evaluation and analysis at any place in the world. Therefore this system can make it more reasonable that evaluating, analyzing, and effective decision making of product design using DFM technique.