• Journal of the Korean Data and Information Science Society
• /
• 제22권4호
• /
• pp.755-764
• /
• 2011

기업은 종종 과거의 필드 고장 데이터를 이용하여 미래에 필드에서 고장이 얼마나 일어날 것인지 예측한다. 특히 이런 예측은 필드에서 예기치 않던 고장모드 (failure mode)가 발견될 때 더욱 하고 싶어진다. 왜냐하면 기업은 이런 예측을 통해 미래에 품질보증 비용이 얼마나 될 것인지 파악하고, 고장 난 부품을 재빨리 수리하는데 필요한 여유 부품의 수를 파악하고 싶기 때문이다. 본 연구에서는 기업에서 생길 수 있는 요약 데이터를 사용하여 미래 필드에서 고장이 얼마나 발생할 것인지 예측하고, 이런 요약 데이터이외에 또 어떤 데이터가 생길 수 있으며 이때 분석결과가 어떻게 나올 수 있는지 알아본다.

• 한국공간구조학회논문집
• /
• 제22권3호
• /
• pp.57-64
• /
• 2022

As earthquakes have increased in Korea recently, people are paying attention to the seismic performance of buildings built in the past. Many school buildings in Korea were built based on standard drawings before the seismic design was applied. However, since school buildings are often designated as emergency evacuation facilities in case of disasters such as earthquakes, seismic evaluation and retrofit must be done quickly. This study investigated the failure modes among structural components (beams, columns, and joints), focusing on 1980s standard drawings for school buildings. The effects of column axial force, partial masonry infills, and different material strengths for concrete and rebar were considered for detailed evaluation. As a result, most of the joints were found to be the weakest among structural components. Column axial forces tended to make the joints more vulnerable, and partial masonry infills increased the possibility of joint failure and shear failure in columns.

• 시스템엔지니어링학술지
• /
• 제9권1호
• /
• pp.65-84
• /
• 2013

This paper introduces a systems engineering approach to reliability centered maintenance to address some of the weaknesses. Reliability centered maintenance is a systematic, disciplined process that produces an efficient equipment management strategy to reduce the probability of failure [1]. The study identifies the need for RCM, requirements analysis, design for RCM implementation. Value modeling is used to evaluate the value measures of RCM. The system boundary for the study has been selected as containment spray pump and its motor drive. Failure Mode and Criticality Effects analysis is applied to evaluate the failure modes while the logic tree diagram used to determine the optimum maintenance strategy. It is concluded that condition based maintenance tasks should be enhanced to reduce component degradation and thus improve reliability and availability of the component. It is recommended to apply time directed tasks to age related failures and failure finding tasks to hidden failures.

• 한국항공우주학회지
• /
• 제38권2호
• /
• pp.111-118
• /
• 2010

복합재료 구조물에서 조인트 부위는 매우 취약한 부분이다. 본 논문에서는 후판 알루미늄-알루미늄 조인트 및 복합재-알루미늄 조인트를 접착제로 접합하여 제작한 다음, 인장실험을 수행하여 파손형태를 고찰하였다. 또한, 항복 변형률에 기초한 수정 파손영역 이론을 제안하였으며, 파괴모드별 파손하중과 상호 비교하였다. 후판 알루미늄-알루미늄 조인트와 복합재-알루미늄 조인트의 파손강도를 동일한 파손기준값을 적용하여 예측하였으며, 제작된 14종류의 시편에서는 최대 19.3% 오차범위 내에서 파손강도를 예측할 수 있었다.

• 한국공작기계학회논문집
• /
• 제12권1호
• /
• pp.58-64
• /
• 2003

A mechanical press joining was investigated in ender for joining A1-5052 sheets for automobile body weight reduction. Static tensile and fatigue tests were conducted using tensile-shear specimens for evaluation of fatigue strength of the joint. During Tox joining process for A1-5052 plates, using the current sheet thickness and punch diameter, the optimal applied punching force was found to be 32 kN under the current joining condition. For the static tensile-shear experiment results, the fracture mode is classified into interface fracture mode, in which the neck area fractured due to influence of neck thickness, and pull-out fracture mode due to influence of plastic deformation of the joining area. And, during fatigue tests for the A1-5052 tensile shear specimens, interface failure mode occurred in the region of low cycle. The fatigue endurance limit approached to 6 percents of the maximum applied load, considering fatigue lifetime of $2.5\times10^6$ cycles.

• Geomechanics and Engineering
• /
• 제28권2호
• /
• pp.117-133
• /
• 2022

Determination of the mechanical behaviour of jointed rock masses has been a challenge for rock engineers for decades. This problem is more pronounced for non-persistent jointed rock masses due to complicated interaction of rock bridges on the overall behaviour. This paper aims to study the effect of a non-persistent joint set configuration on the mechanical behaviour of rock materials under both uniaxial and biaxial compression tests using a discrete element code. The numerical simulation of biaxial compressive strength of rock masses has been challenging in the past due to shortcomings of bonded particle models in reproducing the failure envelope of rock materials. This problem was resolved in this study by employing the flat-joint contact model. The validity of the numerical model was investigated through a comprehensive comparative study against physical uniaxial and biaxial compression experiments. Good agreement was found between numerical and experimental tests in terms of the recorded peak strength and the failure mode in both loading conditions. Studies on the effect of joint orientation on the failure mode showed that four zones of intact, transition to block rotation, block rotation and transition to intact failure occurs when the joint dip angle varies from 0° to 90°. It was found that the applied confining stress can significantly alter the range of these zones. It was observed that the minimum strength occurs at the joint dip angle of around 45 degrees under different confining stresses. It was also found that the joint orientation can alter the post peak behaviour and the lowest brittleness was observed at the block rotation zone.

• 한국건설순환자원학회논문집
• /
• 제11권3호
• /
• pp.177-183
• /
• 2023

유리섬유로 보강된 보강된 보의 경우 초기조건 및 보강형태에 따라 다양한 파괴모드가 발생한다. 본 연구에서는 콘크리트 탄성계수보다 약간 큰 유리섬유 보강재를 적용한 무근 콘크리트보의 파괴거동을 분석하였다. 실험을 위해 24 MPa 강도를 가지는 보를 제작하였으며, 초기 노치, 겹이음, 단부보강, 파이버 앵커 등의 영향을 분석하였다. 노치 및 노치부의 겹이음은 일반보강효과와 비슷한 하중증가를 나타내었는데, 이는 함침된 유리섬유의 에폭시가 노치 단면을 충분히 수복하기 때문이다. 보강하지 않은 기준기편에 비하여 초기 노치의 경우 0.78을, 보강한 경우는 4.43~5.61의 보강효과를 나타내었으며 휨파괴에서 시작되는 계면파괴가 지배적이었다. 높이의 1/3 이상의 단부 스트립과 파이버 앵커를 가진 경우 가장 이상적인 파괴거동(보강재 파단)을 나타내었는데, 일반 보강시편보다 150 % 이상의 파괴하중을 나타내었다.

• 대한치과교정학회지
• /
• 제44권1호
• /
• pp.44-49
• /
• 2014

Objective: To evaluate the effects of ultrasonic instrumentation with different scaler-tip angulations on the shear bond strength (SBS) and bond failure mode of metallic orthodontic brackets. Methods: Adhesive pre-coated metallic brackets were bonded to 72 extracted human premolars embedded in autopolymerizing acrylic resin. The teeth were randomly divided into 3 groups (n = 24 each) to undergo no treatment (control group) or ultrasonic instrumentation with a scaler-tip angulation of $45^{\circ}$ ($45^{\circ}$-angulation group) or $0^{\circ}$ ($0^{\circ}$-angulation group). SBS was tested in a universal testing machine, and adhesive remnant index (ARI) scores were recorded. The Kruskal-Wallis test and Mann-Whitney U-test were used for statistical analysis. Results: The control group had a significantly higher mean SBS value than the treated groups, which showed no significant differences in their mean SBS values. The ARI scores were not significantly different among the groups. Conclusions: Ultrasonic instrumentation around the bracket base reduces the SBS of metallic orthodontic brackets, emphasizing the need for caution during professional oral hygiene procedures in orthodontic patients. The scaler-tip angulation does not influence the SBS reduction and bond failure mode of such brackets.

• International Journal of Concrete Structures and Materials
• /
• 제2권1호
• /
• pp.57-62
• /
• 2008

When the yield line theory is used to estimate the ultimate strength of a concrete barrier, it is of primary importance that the correct assumption is made for the failure mode of the barrier. In this study, a static test was performed on two full-scale concrete barrier specimens of Korean standard shape that simulate the actual behavior of a longitudinally continuous barrier. This was conducted in order to verify the failure mode presented in the AASHTO LRFD specification. The resulting shape of the yield lines differed from that presented in AASHTO when subjected to an equivalent crash load. Furthermore, the ultimate strengths of the specimens were lower than the theoretical prediction. The main causes of these differences can be attributed to the characteristics of the barrier shape and to a number of limitations associated with the classical yield line theory. Therefore, a revised failure mode with corresponding prediction equations of the strength were proposed based on the yield lines observed in the test. As a result, a strength that was more comparable to that of the test could be obtained. The proposed procedure can be used to establish more realistic test levels for barriers that have a similar shape.

• Steel and Composite Structures
• /
• 제35권2호
• /
• pp.215-235
• /
• 2020

Cracks and defects may occur anywhere in a plate under tension. Cracks can affect the buckling stability performance and even the failure mode of the plate. A search of the literature reveals that the reported research has mostly focused on the study of plates with central and small cracks. Considering the effectiveness of cracks on the buckling behavior of plates, this study intends to investigate the effects of some key parameters, i.e., crack size and location as well as the plate aspect ratio and support conditions, on the buckling behavior, stress intensity factor (SIF), and the failure mode (buckling or fracture) in cracked plates under tension. To this end, a sophisticated mathematical code was developed using MATLAB in the frame-work of extended finite element method (XFEM) in order to analyze the buckling stability and collapse of numerous plate models. The results and findings of this research endeavor show that, in addition to the plate aspect ratio and support conditions, careful consideration of the crack location and size can be quite effective in buckling behavior assessment and failure mode prediction as well as SIF evaluation of the cracked plates subjected to tensile loading.