• Journal of Power Electronics
• /
• v.18 no.6
• /
• pp.1708-1719
• /
• 2018

A complete current loop decoupling control strategy based on a sliding mode observer (SMO) is proposed to eliminate the influence of current dynamic coupling and back electromotive force (EMF) in the vector control of permanent magnet synchronous motors. With this strategy, current dynamic decoupling and back EMF compensation can be simultaneously achieved. Unlike conventional methods, the proposed strategy can avoid the disturbances caused by the parametric variations of motor systems and maintain the advantages of proportional integral (PI) controllers, which are robust and easy to operate. An improved SMO, which uses a special PI regulator other than a linear saturation function as the equivalent control law in the boundary layer of a sliding surface, is proposed to eliminate the estimated errors caused by the quasi-sliding mode and obtain a satisfactory decoupling performance. The stability and parameter robustness of the proposed strategy are also analyzed. Physical experimental results are presented to verify the validity of the method.

• ETRI Journal
• /
• v.33 no.1
• /
• pp.121-124
• /
• 2011

Digital harmonics, which may reduce the radio frequency sensitivity of a system, can be coupled with an antenna in a mobile handset. This letter presents a decoupling method for increasing the isolation between digital harmonics on a flexible printed circuit board (FPCB) and an antenna in terms of the ground mode current and the concept of reaction. We model the signal and ground lines in an FPCB as a loop circuit exciting a ground mode current and demonstrate a simple but efficient decoupling method for reducing the excited ground mode current.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.8
• /
• pp.842-848
• /
• 2005

The decoupling control using state feedback was once intensively studied during 1960's by many researchers. However, this control scheme was sensitive to the disturbance and Parameter variations. SMC(sliding mode control) is known as a robust control methodology to overcome such a disturbance. In this paper. the decoupling control by means of SM(sliding mode) for a trajectory control of a two-degrees-of- freedom manipulator was discussed. The position and velocity of manipulator tip were adopted to compose a nonlinear error functions. The reference inputs of the controller can be decided by switching function combined with the desired position and velocity. Simulation result is provided to verify the effectiveness of the proposed control scheme.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1587-1588
• /
• 2007

IPM(Interior Permanent Magnet) Machine의 전류 제어는 자기저항에 의존하는 토크특성 때문에 SPM(Surface Permanent Ma- gnet) Machine보다 복잡하다. 고성능 토크제어를 위해서는 d축 전류와 q축 전류의 동특성간의 상태 decoupling이 요구된다. 그러나 전류의 상태 동특성이 coupling된 인덕턴스의 변화(온도, 파라미터들의 부정확한 측정값)는 상태 decoupling을 어렵게 한다. 그래서 이러한 변화와 각각의 전류가 독립적으로 제어될 수 있게 여러 decoupling 방법들에 초점이 맞춰지고있다. 본 연구는 외란에 강하고, 특히 인덕턴스의 변화와 상관없는 이상적인 토크제어를 하기 위해 신경회로망을 이용하여 슬라이딩 평면(sliding surface)을 구성하고, SMC(Sliding Mode Control)를 이용하여 상태 cross-coupling의 decoupling을 위한 새로운 접근을 제안한다. 이 방법은 PI제어 성능과 SMC의 강인성을 알고리즘을 이용하여 결합한 것이라고 볼 수도 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.7
• /
• pp.1152-1158
• /
• 2004

In this paper, a trajectory tracking problems using SMC(sliding mode control) is presented. In the conventional method. SMC has been applied to linear systems and the output matrix C has to satisfy a restrictive condition that CB is nonsingular. Under suitable assumptions, decoupling SMC can be adapted to remove the restriction mentioned above. The Proposed control strategy is applied to trajectory tracking control and simulations results are given to demonstrate the effectiveness of the proposed control scheme.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.3
• /
• pp.514-521
• /
• 2009

The current control for Interior-mounted Permanent Magnet Motor(IPM Motor) is more complicate than Surface-mounted Permanent magnet Motor(SPM Motor) because of its torque characteristic depending on the reluctance. For high performance torque control, it requirs state decoupling between d-axis current and q-axis current dynamics. However the variation of the inductances, which couples the state dynamics of the currents, makes the state decoupling difficult. So some decoupling methods have developed to cope this variation and each current can be regulated independently. This paper proposes a novel approach for fully decoupling the states cross-coupling using sliding mode control with virtual state for IPM Motor. As a result, in spite of the parameter uncertainty and disturbance, the proposed sliding surface can have the dynamics of nominal system controlled by PI controller.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.702-707
• /
• 2004

In this paper, we proposed the decoupling VSS controllers for a trajectory control of a two degrees of freedom SCARA type manipulator. We decoupled the position and velocity of a manipulator tip by using a nonlinear error functions. The reference inputs of the controller can be decided directly from the desired position and velocity. Simulation result is provided to verity the effectiveness of the proposed control scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.920-925
• /
• 1993

For a multi-input, multi-output system, it is widely known that feedback control gain presents extra freedom pole placement problem. An eigenstructure assignment utilizes this freedom for assignment of all or some elements of the closed-loop eigenvectors. In this paper, a nonlinear optimization technique is adopted to obtain a small gain controller that assigns closed-loop eigenvalues and elements of eigenvectors simultaneously. To illustrate the approach, a numerical example of the Airplane mode decoupling using an advanced fighter is shown.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1334-1337
• /
• 2006

System identification is the field of modeling dynamic systems from experimental data. As a modeling technique, we can mention finite element method (FEM). In addition, we are able to measure modal data as the experimental data. The system can be generally categorized into a gray box and black box. In the gray box, we know mathematical model of a system, but we don't know structural parameters exactly, so we need to estimate structural parameters. In the black box, we don't know a system completely, so we need to identify system from nothing. To date, various system identification methods have been developed. Among them, we introduce system realization theory which uses Hankel matrix and Eigensystem Realization Algorithm (ERA) that enable us to identify modal parameters from noisy measurement data. Although we obtain noise-free data, however, we are likely to face difficulties in identifying a structure with hidden modes. Hidden modes can be occurred when the input or output position comes to a nodal point. If we change a system using a mode decoupling controller, the hidden modes can be revealed. Because we know the perturbation quantities in a closed loop system with the controller, we can realize an original system by subtracting perturbation quantities from the closed loop system. In this paper, we propose a novel method to identify a structure with hidden modes using the mode decoupling controller and the associated example is given for illustration.

• Structural Engineering and Mechanics
• /
• v.64 no.4
• /
• pp.473-485
• /
• 2017

An isolated building, composed of superstructure and isolation system which have very different damping properties, is typically non-classical damping system. This results in inapplicability of traditional response spectrum method for isolated buildings. A multidimensional response spectrum method based on complex mode superposition is herein introduced, which properly takes into account the non-classical damping feature in the structure and a new method is developed to estimate velocity spectra from the commonly used displacement or pseudo-acceleration spectra based on random vibration theory. The error of forced decoupling method, an approximated approach, is discussed in the viewpoint of energy transfer. From the base-isolated benchmark model, as a numerical example, application of the procedure is illustrated companying with comparison study of time-history method, forced decoupling method and the proposed method. The results show that the proposed method is valid, while forced decoupling approach can't reflect the characteristics of isolated buildings and may lead to insecurity of structures.