• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.354-359
• /
• 2012

Improvement of structure-borne noises in the vehicle compartments has been one of the primary concerns in the development of vehicles. The booming is an annoying low frequency interior noise and vibration in vehicle. But it is difficult to reduce the structure-born booming noise in traditional method - trial and error within the shorten development schedule. So in present, the structure dynamic modification (SDM) method helpful to predict the effect of the local mass, stiffness, and damping is introduced. So in order to reduce the interior booming noise, the SDM was performed, and verified with modal test result. It was shown that the interior booming noise was reduced as predicted.

• 한국소음진동공학회논문집
• /
• 제26권5호
• /
• pp.584-593
• /
• 2016

In this study, an improvement design method for reducing the vibration of fenders equipped in a tractor is proposed through the establishment of a finite element model and the topology optimization. As the original shapes of the parts cannot be altered, an improved design model was derived in which a stiffener was attached to the border of parts. Thus, the first resonance frequency was increased by approximately 16 Hz, which was confirmed to be the frequency interval for avoiding the idle and operating frequency of the engine. Finally the improved design model was applied to confirm the effect of vibration reduction. Therefore, it can be concluded that the improved design model of the tractor fender is effective at reducing vibrations of the tractor fender.

• 대한전자공학회논문지
• /
• 제21권1호
• /
• pp.1-6
• /
• 1984

기하광학적 해석방법으로 입사조건에 따른 SCS(step-graded-step) 모드 스크램블러의 near field pattern, 모달 파우어 분포 및 far field pattern을 계산하고, 실험결과와 일치함을 보였다. 이로부터 SGS 모드 스크램블러에 의해 피측정 graded index 광섬유에서 stable mode launching이 이루어짐을 설명하였다. 또한 SGS 모드 스크램블러의 효과적 사용 방법으로는 입사 NA를 적게하는 것이 좋다는 것을 알았으며, 실험으로 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.702-707
• /
• 2000

Under the rapid change of a new vehicle model, it is necessary to develop a durability analysis technique using computer simulation. In order to do this. reliable dynamic stress-time history for the vehicle components must be calculated on various road conditions. In this paper, a full vehicle simulation model which is composed of flexible frame and chassis components is proposed and verified its reliability from the comparison with field test data. Finally, dynamic stress-time history on the rear chassis components is predicted with hybrid and modal superposition method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.440-445
• /
• 2000

Robust tracking controller of optical disk drive(ODD) is designed using quantitative feedback theory(QFT). Nominal plant model is identified from real system through modal test. Uncertainties and control performance of tracking servo are specified, and robust controller satisfying these specifications is designed in the QFT framework. To verify the performances of designed controller, experiment are performed in a digital signal processor(DSP) environment, and experimental results are compared with simulations.

• 한국기계가공학회지
• /
• 제2권2호
• /
• pp.60-66
• /
• 2003

For the estimation of chatter lobe boundary it is very important to calculate the natural mode of cutting process. There are many time series algorithms for getting the natural mode of structural endmilling dynamics considering the cutting process. In this study, we have compared several time series methods such as AR algorithm, ARX, ARMAX, ARMA, Box Jenkins, Output Error, Recursive ARX, Recursive ARMAX considering the sampling frequency. As a results, the ARX, ARMAX and IV 4 are more desirable algorithms for the calculation of modal parameters such as natural frequency and damping ratio In endmilling operation. Also these algorithms may be adopted for the natural mode estimation of endmilling operation for chatter lobe prediction.

• Journal of Mechanical Science and Technology
• /
• 제18권3호
• /
• pp.347-356
• /
• 2004

The flexural vibration characteristics of a sandwich beam system with a partially inserted viscoelastic layer were quantitatively studied using the finite element analysis in combination with the sine-sweep experiment. Asymmetric mode shapes of the flexural vibration were visualized by holographic interferometry, which agreed with those obtained by the finite element simulation. Effects of the length and the thickness of the partial viscoelastic layer on the system loss factor (η$\_$s/) and resonant frequency (f$\_$r/) were significantly large for both the symmetric and asymmetric modes of the beam system.

• 한국기계가공학회지
• /
• 제11권2호
• /
• pp.66-72
• /
• 2012

Ultrasonic metal welder is consisted of power supply, transducer, booster, and horn. Precise designing is required since each part's shape, length and mass can affect driving frequency and vibration mode. This paper gives a description of an experimental study of the ultrasonic welding of metals. A horn suitable for 40,000Hz was attached to the ultrasonic metal welder in order to weld Cu sheet. The Cu sheet welding was done with different amplitude, pressure and welding time, and its maximum tension was measured. Maximum tension of 177.99N was obtained when the pressure was 2.5bar, amplitude was 80%, and welding time was 0.34sec. Therefore, excessive welding condition negatively influences maximum tension measurement result.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.1053-1058
• /
• 2003

Piezoelectric under water acoustic transducer is a kind of device for under water detection working as not only an actuator but also a sensor. The technique that can predict acoustical characteristics of transducer is important for robust design of transducer in harsh underwater environment. This paper represents the development of software for analyzing dynamic characteristics of piezoelectric acoustic transducers based on finite element method. Modal and transient analysis modulo for acoustic transducers are developed TWO dimensional model for Tonpilz transducer is used for the test of the developed nodal and transient analysis modules. and comparison is made with a commercial code, ANSYS.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.533-539
• /
• 2013

Number of components and payload systems installed in satellites were found to be exposed to various disturbance sources such as the reaction wheel assembly, the control moment gyro, coolers, and others. A micro-level of vibration can introduce jitter problems into an optical payload system and cause significant degradation of the image quality. Moreover, the prediction of on-orbit vibration effects on the performance of optical payloads during the development process is always important. However, analyzing interactions between subsystems and predicting the vibration level of the payloads is extremely difficult. Therefore, this paper describes the analytical and experimental approach to microvibration effects on satellite optical payload performance with integrated jitter analysis framework, micro vibration emulator and satellite structure testbed.