• 대한기계학회논문집B
• /
• 제31권9호
• /
• pp.790-798
• /
• 2007

An experimental study was performed to investigate the effects of mixing quality, inlet pressure, nozzle diameter on CO, NO emission and radiation characteristics in porous ceramic fiber radiant burners. Observations of combustion characteristics occurring inside the burner system which was insulated fiber mat, were investigated by measuring emission and radiation characteristics. Combustion was achieved at the firing rate of $88{\sim}99\;kcal/hr$, inlet pressure of $100{\sim}250mmH_2O$. The fiber burner exhibit significant both spectral intensity peaks in the bands at $2.5{\mu}m\;and\;4.0{\mu}m$ relatively. There is a small difference in the variable mixing tube. However spectral intensity increased with the firing rate. CO emissions were found to be strongly dependent on the operating conditions. There was a tendency that CO concentration increased as the firing rate increases. the reason for rise of CO concentration is that is becomes it the relatively rich condition. Relatively low NO emission was observed for the whole operating range. The NO concentration is maximal at the firing rate of approximately 2850 kcal/hr and an air ratio of about 1.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.451-454
• /
• 2006

This paper describes the results of cold flow test and hot firing tests of an uni-element coaxial swirl injector and hot firing tests of a subscale combustor, as to the development effort of coaxial swirl injector for high performance liquid rocket engine combustor. A major design parameter for coaxial swirl injector is the recess number of a bi-swirl injector. The results of hot firing tests of the uni-element injector combustor and the sub-scale combustor are analyzed to investigate the effect of the recess number influencing on the combustion performance and pressure fluctuation. The test results of a cold flow test of the unielement combustor shows that it was shown that the change in recess number has significant effect on mixing characteristics and efficiency, while the effect of recess number on atomization characteristic is not The results of a series of firing tests using unielement and subscale combustor show that the recess length significantly affects the hydraulic characteristics, the combustion efficiency, and the dynamics of the liquid oxygen/kerosene bi-swirl injector. As a point of combustion performance, combustion efficiencies are 90% for unielement combustor and 95% for subscale combustor. The difference in the characteristic velocities between the unielement combustor and the subscale combustor may be caused by the difference in thermal loss to the combustor wall and the relative lengths of the combustion chamber. For a mixed type coaxial swirl combustor, the pressure drop across the injector increases as recess number becomes larger. The low frequency pressure fluctuation observed in unielement combustor can be related to the propellant mixing characteristics of the coaxial bi-swirl injector. The effect of the recess number on the pressure fluctuation inside the combustion chamber is more significant in un i-element combustor than the subscale combustor, of which the phenomena are also observed in time domain and frequency domain.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.225-228
• /
• 2009

추력 75톤급 액체로켓엔진용 기술개발/검증 시제인 가스발생기의 연소시험이 수행되었다. 가스발생기 분사기 및 헤드의 성능을 먼저 확인하기 위해 heat-sink 형태의 연소실이 사용되었다. 본 논문에서는 연소시험을 위한 준비상황 및 기술검증시제 연소시험에서 얻어진 압력, 온도 분포, 압력 섭동 등의 결과들을 설명하였다.

• 한국세라믹학회지
• /
• 제17권2호
• /
• pp.69-74
• /
• 1980

This study deals with the wire content, wire diameter, aspect ratio , it's arrangement of steel, wire fiber and the sorts of castable which affected the character of steel wire fiber reinformced refractory castable. Two kinds of alumina based refractory castables, one is for 1650℃ and the other is for 1800℃, and stainless steel which is SUS 304 type 0.25, 0.34 , 0.37 and 0.50m/min diameter were used respectively. Aspect ratio was adjusted to 50, 75, 100 and steel fiber content was also adjusted to 1-4wt% each. The results of the experiment were as follows : 1. At firing temperature around 1,000℃, MOR is increased with increasing wire content and aspect ratio with decreasing firing temperature, which depends on the Romualdi's Fiber Spacing Theory. But for calculation of the fiber spacing, Swamy equation is more a aplicable to the extensive fiber mixing conditions. However, the condition differs from the above at firing temperature around 1,350℃ ,because of the degradation of wire and the progress of sintering of castable. 2. Linear change is getting larger corresponding to the increase of wire content, and the spaling resistivity is increasing corresponding to the increase of wire content and to aspect ratio, and with decreasing wire diameter. 3. Firing shrinkage under load is getting greater as higher wire content, and the shrinkage of the test pieces which fiber is vertically oriented is getting greater than the test pieces which fiber is randomly oriented.

• 한국전기전자재료학회논문지
• /
• 제22권9호
• /
• pp.776-780
• /
• 2009

In this study, the opto-electric properties of EL devices with PMN dielectric layer with variation of firing tempereature were investigated. For the PMN dielectric layer process, the paste was prepared by optimization of quantitative mixing of PMN powder, $BaTiO_3$, Glass Frit, $\alpha$-Terpineol and ethyl cellulose. The EL device stack consists of Alumina substrate ($Al_2O_3$), metallic electrode (Au), insulating layer (manufactured PMN paste), phosphor layer (ELPP- 030, ELK) and transparent electrode (ITO), which is well structure as a thick film EL device. The phase transformation properties of PMN dielectric with various firing temperatures of $150^{\circ}C$ to $850^{\circ}C$ was characterized by XRD. Also the opto-electric properties of EL devices with different firing temperature were investigated by LCR meter and spectrometer. We found the best opto-electric property was obtained at the condition of $550^{\circ}C$ firing which is 3432.96 $cd/m^2$ at 1948.3 pF Capacitance, 40 kHz Frequency, 40% Duty, Vth+330 V voltage.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1721-1723
• /
• 1997

In AC Plasma Display Panel(PDP), serious problems are low radiation brightness and very high discharge voltage. To solve these problems, it is necessary to obtain optimal frequency of drive waveform and optimal gas mixing ratio. This paper presents firing voltage and sustain voltage as frequency of waveform and gas mixing ratio, and proposes optimal frequency of drive waveform and optimal gas mixing ratio.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.1-9
• /
• 2014

The vast stores of biomass available in the worldwide have the potential to displace significant amounts of petroleum fuels. Fast pyrolysis of biomass is one of several paths by which we can convert biomass to higher value products. The wood pyrolysis oil (WPO) has been regarded as an alternative fuel for petroleum fuels to be used in diesel engine. However, the use of WPO in a diesel engine requires modifications due to low energy density, high water contents, high acidity, high viscosity, and low cetane number of the WPO. One possible method by which the shortcomings may be circumvented is to co-fire WPO with other petroleum fuels. WPO has poor miscibility with light petroleum fuel oils; the most suitable candidates fuels for direct fuel mixing are methanol or ethanol. Early mixing with methanol or ethanol has the added benefit of significantly improving the storage and handling properties of the WPO. For separate injection co-firing, a WPO-ethanol blended fuel can be fired through diesel pilot injection in a dual-injection dieel engine. In this study, the performance and emission characteristics of a dual-injection diesel engine fuelled with diesel (pilot injection) and WPO-ethanol blend (main injection) were experimentally investigated. Results showed that although stable engine operation was possible with separate injection co-firing, the fuel conversion efficiency was slightly decreased due to high water contents of WPO compare to diesel combustion.

• 한국재료학회지
• /
• 제24권8호
• /
• pp.407-412
• /
• 2014

Currently, diopside ($MgCaSi_2O_6$) crystal glaze is used frequently for pottery works or in earthen wares, though the process is not straightforward. However, to create and control the positions and sizes of the crystals in desired amounts when making pottery is difficult. To solve this problem, a diopside crystal seed was created at a temperature of $1450^{\circ}C$. After planting this seed in the glaze, a glaze combination and firing process which allows a user to create crystals with the desired position and at the desired size were established. In addition, in order to investigate the creation process of the crystals, the growth patterns of the crystals were observed and examined using Raman spectrography and XRD and SEM analyses. As a result, the optimum synthesis condition of the diopside seed was created by mixing 1 mole of $CaCo_3$, 0.2 mole of $(MgCo_3)_4(MgCoH)_2{\cdot}5H_2O$ and 2 moles of $SiO_2$ and then applying a firing process to the mixture at $1,450^{\circ}C$ for 30 minutes. The optimum glaze content of the seed was 70 % feldspar, 20 % limestone and 10 % $MgCo_3$. For the firing process, it was confirmed that the size of crystal is larger with a longer firing time at $1100^{\circ}C$ by completing a two-hour process at $1280^{\circ}C$. In addition, the diopside crystal has columnar structure and is less than $1{\mu}m$ in size.

• 한국광물학회지
• /
• 제27권2호
• /
• pp.63-72
• /
• 2014

본 연구에서는 경상남도 창녕군 창녕읍 교리 고분군 일대에서 발견된 5세기~6세기 초반 무렵의 삼국시대 토기를 대상으로 암석학적 연구방법을 적용하여 광물학적 특징과 소성온도 및 환경을 추정하였다. 이를 위하여 광물학적 동정과 미세조직관찰, 화학성분 분석 등의 다양한 기법을 적용하여 암석광물학적 분석을 시행하였다. 편광현미경 하에서 토기 시료들을 관찰한 결과 석영, 장석류가 주구성 광물이었으며, 그 외에도 규장질 화산암(felsic volcanics), 비짐(temper), 저급점토에 주로 함유되는 불투명광물 등이 관찰되었다. XRD와 FTIR을 통해 현미경으로 볼 수 없었던 멀라이트, 적철석, 스피넬 등이 관찰되었다. 조사된 토기시편에서 보이는 흐름선과 색이 다른 기질이 혼재는 두 가지 이상의 점토를 사용하였거나 반죽과정에서 생긴 것으로 보인다. 소성온도가 $1,200-1,300^{\circ}C$로 제작된 토기에서 관찰되는 일반적인 석기의 특징은 보이지 않으나 다소의 기공이 존재하고 석영을 비롯한 특정 광물들의 결정이 남아 있는 것으로 보아 소성온도는 $1,000^{\circ}C$ 정도에서 소성되었을 것이라 추정된다. 고온광물인 멀라이트가 토기의 내부보다는 외곽부나 균열 부근에서 주로 관찰되며 토기 내외부의 산화정도가 다른 것은 균질한 소성환경이 조성되지 않았음을 의미한다. 대부분의 시료에서 규장질 화산암편이 관찰되고 일부 시료에서 크리스토발라이트가 관찰되는데, 크리스토발라이트의 형성온도가 일반적으로 1,470^{\circ}C$ 이상임을 감안하면 소성 시 생성된 것이 아니라 원래의 태토 내에 포함되어 있던 것으로 추정된다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.114-118
• /
• 2007

본 연구는 30ton급 액체로켓엔진 지상연소시험용 연소기의 설계 및 제작에 관한 것이다. 본 연소기는 연소압력이 60 bar, 노즐 확대비가 12이며, 헤드부와 연소실부가 용접되는 일체형 재생냉각형 연소기이다. 헤드부는 저온에서 기계적 특성이 좋은 STS316L을 사용하였다. 연소실부는 실린더부, 노즐목부, 1차 노즐부, 2차 노즐부로 구성되어 있다. 연소실부의 내피 재질은 동합금 /STS319J1/STS316L, 외피 재질은 STS329J1을 사용하였다. 선반, 밀링, MCT, 롤링 및 프레싱 등의 기계적 가공을 통하여 단품들을 완성하였다. 이러한 각 단품들을 조립하여 일반 용접 및 전자빔 용접, 브레이징 등을 적용하여 일체형으로 접합하였다.