• Journal of Food Hygiene and Safety
• /
• v.14 no.3
• /
• pp.293-304
• /
• 1999

The purpose of this study was to evaluate the microbiological quality, and to assure the hygienic safety of the food production in the university food service facility located in Seoul in accordance with the Hazard Analysis Critical Control Point(HACCP) concepts. In the hygienic state assessment of kitchen, it has revealed that it was very important to remove water from the kitchen floor and to establish standard method for disinfection of cooking utensils. And foodservice workers were required to have training program for the safe handling of food and utensils since they did treat food without hygienic gloves. The kitchen layout had to be improved because the near distance of table with heating unit and shelf might cause the growth of microorganisms when prepared food was kept on the shelf. In terms of the timetemperature measurement and microbiological quality assessment during each of the food production phases, most of sengchae (raw vegetable dish) and namul (cooked vegetable dish) were treated within danger zone for food safeness ($5~60^{\circ}C$). It has shown that the microbiological quality of raw materials was very much inferior at the time of receiving based on the TPC($10^{5}~10^{7}$), coliform($10^{3}~1O^{6}$), which was not acceptable level(TPC:$10^{6}$, coliform:$10^{3}$) suggested by Solberg. Microbiological growth has increased in the both of sengchae and namul considerably during most of food production phase. Therefore, it is extremely important to reduce holding and serving time and to avoid treating food within the danger zone for food safeness. In addition, the prevention of cross-contamination during mixing the ingredients with improper equipments and with insanitary treatments by workers was also important to keep the food safety in this speciqic university foodservice facility.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.4
• /
• pp.113-121
• /
• 2011

River sand has generally used for the backfill material of underground power cables. The thermal resistivity of it has $150^{\circ}C$-cm/Watt in wet condition and more than double in dry condition. The final goal of this study is to find the backfill material which has a small change in thermal resistivity with various water contents, for example thermal resistivity is $50^{\circ}C$-cm/Watt and $100^{\circ}C$-cm/Watt in wet and dry conditions respectively. In this study it is presented that the comparison of thermal resistivity using stone powder, crush rock, weathered granite soil and Jumunjin sand as well as river sand in the needle method regarding water content, dry unit weight and particle size distribution. As a result, the thermal resistivity of a material is minimized when they have maximum dry unit weight at optimum moisture content and maximum density by appropriately mixing materials for particle size distribution. Therefore thermal resistivity characteristics should be considered two factors: one is the difference between natural dry condition and dry state after optimum moisture content, and the other is the difference between unit weight of raw material and maximum dry density.

• Journal of the Korean Society of Costume
• /
• v.51 no.5
• /
• pp.113-134
• /
• 2001

This study was carried out with an objective to prepare the framework of conformity for the 21st century modern fashion, which is interactive with mankind, based on a position that the 21st century contemporary fashion with its amalgamating trend of diversified artistic forms may not be elucidated on a standpoint centering on one certain modality. The hybrid fashion trend of historical modality which provides freedom and satisfaction in creation of an individuals expressive power in expressing true desire of mans inside through man-centered thought of the times has made multifarious motives of the past and present fragmentary. It thus extracts inner divisions and the concept of consolidation through three-dimensional form. Modern fashion is newly interpreted by the material and details of high technologies. and is harmonized by mix and match with various expressions. By having it, it is being expressed together with many types of dresses and ornaments. Modern fashion is being expressed together with many types of dresses and ornaments by new interpretations with the material and details of high technologies and by being harmonized with mix and match with various expressions. The hybrid fashion design trend of regional elements formed by stimuli and contacts of diverse local culture by globalization of network that was achieved by scientific technologies of the contemporary information society has disintegrated varied boundaries in the conventional culture by the latest communication technology-new media on the basis of newly created culture. The fact that regional elements could be expressed as if they were interrelated without each being deprived of originality may be explained with an interpretation on pluralism. The hybrid fashion design trend of cultural aspect, which manifests in the background of scientific technological culture as it transcends the societal-cultural boundaries based on the de-centralization theory of Frederic Jameson, has supplemented the imperfect meanings through conversional correlation with other forms and internal program changes. The middle stratal and polyhedral characteristics are seen as each cultural element is dismantled and reassembled by application of 'multiple-time point expression'. Design forming method is not to bring destruction from outside, but to embrace instability and chaos through radical dismantling of the inside. and to pursue diversity and openness. Thus. it is implemented by an approach that takes the role of design process. In communication of discontinuity, continuity was dismantled through forms of mixing, overlap, perversion, insertion and coincidence.

• Composites Research
• /
• v.23 no.3
• /
• pp.31-36
• /
• 2010

A new material, carbon-nanofiber/polypyrrole (CNF/PPy) composite films, with different CNF weight ratios were fabricated electrochemically. Compared to the fabrication process based on simple physical mixing, the flexibility of the new film has been improved much better than the previous similar material. Pure PPy films were also fabricated by the new electrochemical process for the comparison of difference. Several SEM images were taken at two locations (electrode-side and solution-side) and at the cross section of the samples. Electrical conductivity of the composite films was measured by the four-probe method. The conductivity of the pure PPy film 0.013cm thick was 79.33S/cm. The CNF/PPy composite film with 5% CNF showed a conductivity of 93S/cm. One with 10% CNF showed a conductivity of 126 S/cm. The conductivity of PPy improves, as the CNF weight ratio increases. The good conductivity of CNF/PPy composites makes them a candidate for a small bending actuator. A bending sensor consists of PPy and PVDF, which can be operated in the air, was designed and the bending deflection was calculated using FEM.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.2
• /
• pp.141-151
• /
• 2015

A new rock excavation method using an abrasive injection waterjet system has been developed to enhance the efficiency and reduce the vibration of tunnel excavation. The abrasive feed rate is an important factor for the cutting performance and the economical efficiency of waterjet-based excavation. In this study, various experiments were performed to explore the effects of major process parameters for both the abrasive feed rate and the suction pressure occurring inside the mixing chamber when the abrasives are inhaled. Experimental results reveal that the abrasive feed rate is affected by geometry parameters (abrasive pipe height, length, and tortuosity), abrasive parameters (abrasive particle size), and jet energy parameters (water pressure and water flow rate). In addition, the relation between the cutting performance and the abrasive feed rate was discussed on the basis of the results of an experimental study. The cutting performance can be maximized when the abrasive feed rate is controlled appropriately via careful management of major process parameters.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.5
• /
• pp.1138-1150
• /
• 2020

In this study, an experiment was conducted to develop a sunscreen with antioxidant effects by simultaneously investigating the antioxidant and UV protection capabilities of various plant extracts. First, to investigate the UV-blocking ability of 33 kinds of plant extracts, the absorbance spectrum between the UV wavelength of 280 to 400 nm was investigated. Arrowroot, graviola, wheat sprout, sangbaek skin, thorn meal, lacquer, etc. 11 species were selected. The total polyphenol content, total flavonoid content, and DPPH radical scavenging activity of the selected plant extracts are measured to examine the degree of antioxidant activity, and from this, it is a plant extract that has excellent UV protection and antioxidant activity at the same time. The species was selected. A gel-shaped cream is prepared by mixing the selected gold, hops, and licorice extracts in a ratio of 1:1:1, and the UV protection effect of this cream is measured when the cultured cells are irradiated with UV rays. Determined by the method. As a result of the study, it was confirmed that the selected mixture of plant extracts complemented each other in terms of ultraviolet absorption ability and increased cell damage protection effect. Through these results, it was confirmed that it was possible to develop a sunscreen with an antioxidant effect if the antioxidant and sunscreen capabilities of various plant extracts were determined at the same time.

• Polymer(Korea)
• /
• v.30 no.1
• /
• pp.85-89
• /
• 2006

The effect of vapor grown carbon fiber (VGCF) contents on electrical and rheological properties of VGCF filled polyphenylene sulfide (PPS) composites prepared through melt mixing using a twin screw exruder was studied. This method was proved to be quite effective to produce good dispersion of VGCF in the matrix even for highly filled PPS. From the dependence of the electrical conductivity on VGCF content, the percolation phenomena began to occur above $10\;wt\%$. While there is only a marginal increase of viscosity for 1 and $5\;wt\%$ VGCF filled PPS, the composites containing $10\;wt\%$. While VGCF showed abrupt increase in viscosity as well as flattening of frequency vs modulus curve, indicating a transition from a liquid-like to a solid-like behavior due to the creation of VGCF network. This result agrees well to the fact that the network formation in the composite can be composite by rheological property dependence on filler content as well as by electrical conductivity measurement.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.793-798
• /
• 2017

In modern naval ships, an infrared signature suppression (IRSS) system is used to reduce the metal surface temperature of the heated exhaust pipe and high-temperature exhaust gases generated from the propulsion system. Generally, the IRSS systems used in Korean naval ships consist of an eductor, mixing tube, and diffuser. The diffuser reduces the temperature of the metal surface by creating an air film due to a pressure difference between the internal gas and the external air. In this study, design variables were selected by analyzing the shapes of a diffuser designed by an advanced overseas engineering company. The characteristics of the design variables that affect the performance of the IRSS were investigated through the Taguchi experimental method. A heat flow analysis technique for IRSS systems established in previous studies was used analyze the performance of the diffuser. The performance evaluation was based on the area-averaged value of the metal surface temperature and exhaust gas temperature at the outlet of the diffuser, which are directly related to the intensity of the infrared signature. The results show that the temperature of the exhaust gas was significantly affected by changes in the diameter of the diffuser outlet, and the temperature of the diffuser's metal surface was significantly affected by changes in the number of diffuser rings.

• Economic and Environmental Geology
• /
• v.43 no.2
• /
• pp.177-184
• /
• 2010

When cement grout is used for waterproofing of grounds, important roles are played by fluidity, particle size and bleeding. The most important element which determines their characteristics is the water/cement ratio of grout. Moreover in order to improve the efficiency of soil permeation, micro cement with a smaller average diameter is used in addition to ordinary portland cement. Besides the mixing ratio and cement diameter, the condition of ground is also of fundamental importance in the efficiency of permeation. In order to evaluate grout in terms of permeation ability into ground, we need a field test of grounting, which is cost and time consuming. In this paper we present a laboratory test method in which the suitability and efficiency of grouts are simply and more practically tested. In Korea neither a test standard nor devices are available to simulate grouting in a laboratory. We devised a grout injection equipment in which grouting was reproduced in the same condition with different materials, and suggested a standard for the production of specimens. Our tests revealed that the efficiency of injection increases with the water/cement ratio. We also found that more efficiently injected is the grout with the order of decreasing size; MS8000, micro cement, and ultra fine cements, and colloidal super cement.

• Journal of Energy Engineering
• /
• v.21 no.2
• /
• pp.119-123
• /
• 2012

Although LNG storage tanks are very delicate with chloride attack owing to its operating inshore location, specific integrity management system for chloride attack has not been studied so far. As the design warranty life time, about 25 years, has come, to prevent paying huge amount of construction cost and required resources for new alternative storage tanks and manage the life time of operating storage tanks, the basic data of chloride attack is necessary. This study intended to build up basic data for following detailed study to develop technologies for life time management of LNG storage tanks, NT Build 492 method in North Europe was used to test chloride diffusion coefficient for the newly-constructing concrete outer tank. Results of these tests lead us to the conclusion that 90 days diffusion coefficients show 46% of 28 days' due to a large quantity of fly ash mixing and much similar to estimation from concrete process table. It seems resonable to conclude that 90 days specimens are recommended estimating the chloride diffusion coefficient for LNG storage tanks to enhance the reliabilities.