• Membrane Journal
• /
• v.2 no.2
• /
• pp.135-143
• /
• 1992

Separation of $N_2-SO_2$ mixed gas by polymer membranes, SEPA-97(CA), TFC, and FT-30 membrane, was investigated by varying pressure and temperature. The permeability coefficients and the separation factors of mixed gases were measured, and the influence of various factors on the gas permeability characteristics and separation performance were investigated. The range of pressure was 0.1~1.0 MPa, and that of temperature was 283~303 K. The experimental results showed that the permeability coefficients and the separation factors were increased with an increase in pressure, but they were deereased with increasing temperature. Among the examined membranes, FT-30 possessed the best gas-separating characteristics.

• Journal of Environmental Health Sciences
• /
• v.19 no.4
• /
• pp.38-43
• /
• 1993

The characteristics of food wastewater treatment in an anaerobic packed bed reactor (APBR) with polyurethane as a packing material and sludge bed reactor (ASBR) was studied. The reactor of 9cm-ID, 150cm-height was fed in a continuous mode from bottom of reactor. For the purpose of constant temperature of reactor, water jacket was installed. The used packing materials was polyurethane sponge foam. Methane which was produced by decomposed organics collected at the top of the reactor for using as a fuel. The substrates used were synthetic, mixed and food wastewater. For the acclimatization of microorganisms, mixed wastewater was used. The major analyses were gas production, COD, pH and volatile acids. Based upon the completed works, the results are as follows: When food wastewater was fed the quantity of produced gas was less than that of synthetic wastewater, but food process saw higher methane content than synthetic process. As well as COD removal efficiency of food process reached at about 85%. In aspect of effluent volatile acid, food process showed low concentration of below 500 mg/l, therefore anaerobic reaction stabled. Conclusively food wastewater used can be digested by anaerobic treatment, especially anaerobic packed bed reactor showed 82% of COD removal, 75% of methane content, 10 l of gas production, and anaerobic sludge bed reactor did 79% of COD removal, 75% of methane content, 81 of gas production at 4 kgCOD/m$^3$day, 36$\circ$C.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.2
• /
• pp.85-90
• /
• 2017

The carbon steel formed the thick, somewhat porous, loosely adherent iron oxide scale when oxidized at $500-800^{\circ}C$ for 15 h in air. It formed the thicker, more porous, nonadherent scale consisting of FeS plus iron oxides in $Ar/1%SO_2$-mixed gas. It formed the much thicker, more porous, nonadherent scale consisting of FeS plus iron oxides in Ar/0.1% $H_2S$-mixed gas. However, the aluminized carbon steel formed the thin, protective $Al_2O_3$ surface scale even in $Ar/1%SO_2$-, and $Ar/0.1%H_2S$-mixed gas. Aluminizing drastically improved the corrosion resistance in (O, S, H)-containing gas.

• Journal of the Korean Institute of Gas
• /
• v.20 no.3
• /
• pp.46-51
• /
• 2016

Natural gas liquefaction process which spends a huge amount energy is operated under cryogenic conditions. Thus, many researchers have studied on minimizing energy consumption of LNG plant. However, a few studied for cost optimization have performed. This study focused on the cost analysis for the single mixed refrigerant (SMR) process, one of the simplest natural gas liquefaction process, which has different capacity. The process capacity is increased from 1 million ton per annum (MTPA) to 2.5 MTPA by 0.5 MTPA steps. According to the increase of plant size, only flow rate of natural gas and mixed refrigerant are increased and other operating conditions are fixed. Aspen Economic Evaluator(v.8.7) is used for the cost analysis and six tenths factor rule is applied to obtain multi stream heat exchanger cost data which is not supplied by Aspen Economic Evaluator. Moreover, the optimal plant sizes for different sizes of gas wells are found as the result of applying plant cost to small scale gas wells, 20 million ton (MT), 40 MT, and 80 MT. Through this cost analysis, the foundation is built to optimize LNG plant in terms of the cost.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.12
• /
• pp.3877-3880
• /
• 2013

• Journal of the Korean Institute of Gas
• /
• v.15 no.6
• /
• pp.51-56
• /
• 2011

Mixed gas cylinder(80% Ar, 20% $O_2$) exploded three years ago. But the cause of cylinder rupture was not identified and the case was finished. This paper is the discussions on the cause of cylinder explosion with the investigation report by the police and the similar accident cases. The cause of explosion is the chemical reaction in the cylinder. This accident is similar with the explosion of pressurized oxygen cylinder.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1396-1399
• /
• 2005

Gas permeability of the solidified sewage sludge needs to be characterized in order to use as a large-scale landfill cover material. Four different types of the samples were prepared for gas permeability experiments: (1) granite soil, (2) dried sewage sludge, (3) solidified sewage mixed with slag and (4) solidified sewage mixed with granite soils. The experimental instrumentation and measurement devices were newly designed and created to effectively evaluate gas permeability of the samples.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.7
• /
• pp.1082-1091
• /
• 2004

Analyzed Parametrically was an internal combustion engine combined with gas turbine the cycle of which is splitted into compression side cylinder and expansion side one, and heat adding of which is during constant volume pressure, temperature process. The advantages of each measures were analyzed by means of thermal cycle diagram. The thermal efficiency of partial load cutting off firstly isothermal heat adding and secondly isobaric heat adding also was analyzed The authors suggested some potentials about the performance as for thermal efficiency, mean effective pressure and reducing emissions and noise supposed were the operating parameter of the engine set to some values and were some problems solved.

• Journal of the Korean Ceramic Society
• /
• v.23 no.5
• /
• pp.61-66
• /
• 1986

The gas mixtures ($H_2$/$N_2$, He/$N_2$) having a high thermal conductivity allow the heat generated by the nitriding exotherm to be dissipated from the compact in to the nitriding atmosphere permitting a more accurate control of temperature and produces a more uniform microstructure. In order to observe the effect of the mixed gas atmosphere on the microsturcture of RBSN. the specimen was nitrided in the mixed gas atmosphere which was containe up to 50vol% $H_2$ or He for 0-12 hrs at 135$0^{\circ}C$. The addition of hydrogen to nitrogen gas resulted in the growth of a-needle at the early stage of nitrding increase of the reaction rate and a finer and more uniform microstructure. in case of the addition of helium the behaviour of reaction was similar to the one with pure nitrogen. As the amount of helium was increased a coarse microstructure was formed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.283-284
• /
• 2005

Al electrode for OLED was deposited by Facing Targets Sputtering(FTS) system which can reduce the damage of organic layer. The Al thin films were deposited on the slide glass as a function of working gas such as Ar, Kr or mixed gas. The film surface image was observed by AFM and SEM. In the results, when Al thin film were deposited using mixed gas, the surface morphology was improved in some region.