• Korean Journal of Materials Research
• /
• v.21 no.6
• /
• pp.299-302
• /
• 2011

[ $WO_3$ ]powders were ball-milled with an alumina ball for 0-72 hours. $In_2O_3$ doped $WO_3$ was prepared by soaking ball-milled $WO_3$ in an $InCl_3$ solution. The mixed powder was annealed at $700^{\circ}C$ for 30 min in an air atmosphere. A paste for screen-printing the thick film was prepared by mixing the $WO_3$:In2O3 powders with ${\alpha}$-terpinol and glycerol. $In_2O_3$ doped $WO_3$ thick films were fabricated into a gas sensor by a screen-printing method on alumina substrates. The structural properties of the $WO_3$:$InO_3$ thick films were a monoclinic phase with a (002) dominant orientation. The particle size of the $WO_3$:$InO_3$ decreased with the ball-milling time. The sensing characteristics of the $In_2O_3$ doped $WO_3$ were investigated by measuring the electrical resistance of each sensor in the test-box. The highest sensitivity to 5 ppm $CH_4$ gas and 5 ppm $CH_3CH_2CH_3$ gas was observed in the ball-milled $WO_3$:$InO_3$ gas sensors at 48 hours. The response time of $WO_3$:$In_2O_3$ gas sensors was 7 seconds and recovery time was 9 seconds for the methane gas.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.43 no.4
• /
• pp.273-279
• /
• 2017

In this study, low viscous O/W (oil-in-water) nano-emulsion with fatty acid and fatty alcohol was prepared by phase inversion emulsification method using Tween 80 and Span 80 widely used in cosmetic products. The particle size of the nano-emulsion was increased as increasing the concentration of fatty alcohol in oil phase. Adjusting the HLB of mixed surfactants, a stable nano-emulsion with a narrow size distribution was produced. Similar change in viscosity and electrical conductivity in both systems containing fatty acid and fatty alcohol was shown in the vicinity of the phase inversion point. However, high viscosity was shown in a wide range of different aqueous fraction unlike the system consisting only oils and surfactants. The low viscous nano-emulsion with less than 100 nm droplet size was stable for one month or more at room temperature. O/W nano-emulsions with low viscosity containing fatty acid or fatty alcohol produced by low-energy emulsification method can be widely used as formulations of cosmetics.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.159-170
• /
• 2003

In this study, the mixed design of grout with hish strength.high permeation.high durability and environmental stability as the state of the art in material field was performed. Also, the subjects of grouting, grouting effects for ground conditions, and environmental effects were analyzed. According to these results, the fundamental data will be suggested as a design of grouting in the field application. The physical, mechanical and chemical characteristics with particle shape of the grouts were analyzed. Then, the gel-time of grouts, which is essential for workability and permeation range, were controlled. Also, the laboratory model grouting tests were performed to find the characteristics of solidification, permeation and durability with grouts. The ordinary portland, slag and microcement which have been used in the construction field were evaluated fur the environmental effects. To find the leaching of $Cr^{6+}$characteristics in cement grouts, $Cr^{6+}$ leaching tests were performed for the raw materials. Also, the results of leaching test were shorn by surrounding environment. Then, the unconfined compression strength tests were performed with the homo-gel samples, and the amount of changed $Cr^{6+}$ was measured by curing solution.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.9
• /
• pp.85-95
• /
• 2012

The method of using organic acid is more environment-friendly for it improves the strength of the ground. The method of proliferating microbes makes soil particle bonded, finally improves the strength of the ground and decreasing permeability. Although there has been the research on the effect of strength increasing, there has never been a research on the evaluation of field application. In this paper, through the light drop weight test, the dynamic cone penetration test, the field density test, the variation of strength was investigated in the mixed ground with organic acid for 56 days. As the results of the field test, it was found that the strength and stiffness of the ground increased with organic acid, and that through SEM-EDS, the precipitation of calcium carbonate made by specified microbe obviously increased with organic acid material and so the ground was improved. Therefore, the sustainable development of this method needs to be analysed more in the future.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.205-211
• /
• 2010

The water-sewage cohesion agent(polyaluminumchloride(PAC)) and NaOH were used to synthesize $Al(OH)_3$. For various additions of NaOH, characteristics of the synthesized $Al(OH)_3$ was analysed by XRD, SEM and PSA. According to XRD analysis, small amount of NaOH(NaOH:PAC=15g:100g) resulted in amorphous form of $Al(OH)_3$. By increasing NaOH(NaOH:PAC=20g:100g), the mixture of gibbsite(37%), bayerite(35%) and boehmite(28%) were produced. By adding more NaOH(NaOH:PAC=25g:100g), binary mixtures of gibbsite(67%) and bayerite(33%) were formed. Finally, high addition of NaOH(NaOH:PAC=30g:100g) gave the high concentration of gibbsite(gibbsite:bayerite=83:17). Also, SEM analysis indicated that the product featured the plate form with 20 and 30g of NaOH addition. Furthermore it was found that the particle size of the product decreased with the addition of NaOH.

• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1120-1126
• /
• 2003

Yttrium Aluminum Garnet (YAG) powders were prepared by precipitation of Y hydroxides during milling of alumina powders. The powder calcined at 1200$^{\circ}C$ for 4 h contained a small amount of Yttrium Aluminum Monoclinic (YAM) in addition to YAG. However, phase-pure YAG was obtained in the compact of the milled powder with an average particle size of 0.57 ${\mu}$m at 1300$^{\circ}C$, which is much lower than those (l500∼1600$^{\circ}C$) for a mixed oxide method. The powder was found to exhibit an excellent sinterability regardless of the addition of a sintering aid, SiO$_2$(350 ppm Si). The undoped sample were sintered to a relative density of 98% at l600$^{\circ}C$. In contrast, the addition of SiO$_2$ caused a considerable densification to occur at 1500$^{\circ}C$ and the relative density reached 97.7%. But the sintering aid had little effect on the densification at 1600$^{\circ}C$, showing a similar relative density to the undoped sample.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.8
• /
• pp.1153-1158
• /
• 2012

Niobium oxide ($Nb_2O_5$) has a strong chemical coherence and good electrical conductivity. Therefore, this material is helpful to enhance the performance of the dye sensitized solar cells (DSC) by improving the electron mobility. In this study, $Nb_2O_5$ was mixed with $TiO_2$ and this compound was applied to the DSC to improve its performance. As a result, the current density of the DSC using the $Nb_2O_5-TiO_2$ compound on the photoelectrode was increased, because the internal resistance concerned to the electron transfer in the photoelectrode of DSC was decreased. However, large amount of the $Nb_2O_5$ induces the decrease of the efficiency of the DSC because the surface area to attach dye molecules is decreased due to the large particle of $Nb_2O_5$. Therefore, it is important to optimize the mixture ratio of the $Nb_2O_5-TiO_2$ compound for maximizing the performance of the DSC. Finally, the most optimum performance of the DSC was shown in case of the $Nb_2O_5$ concentration of 10 wt% of the $Nb_2O_5-TiO_2$ compound.

• Analytical Science and Technology
• /
• v.17 no.2
• /
• pp.173-179
• /
• 2004

The $BaTiO_3$ powders and thin films were prepared by an alkoxide modified sol-gel process (polymerization-complex route) using ethylene glycol. The stable starting (Ba-Ti)-mixed metal organic sol was made by addition of acetylacetone. The $BaTiO_3$ powders, which had a particle size of 40~77 nm, were crystallized from an amorphous to a tetragonal phase on annealing at 700 and $1100^{\circ}C$ for 1 h. From FT-IR, solid-state $^{13}C$ CP/MAS NMR spectroscopy and X-ray diffractometry, the trace of the Ba-Ti-oxycarbonate phase first appeared at $400^{\circ}C$. Hydrolyzed sol was spin coated on a quartz wafer at 3500 rpm for 60 s and pyrolyzed at $1100^{\circ}C$ for 1 h. After heat treatment, the coated layer became dense and smooth.

• Resources Recycling
• /
• v.9 no.3
• /
• pp.3-12
• /
• 2000

A Study on the cementation for the recovery of Cu, Ni and Co with Mn metallic powders in leaching solution from the manganese nodule that have removed Fe ions was studied. The results showed that the recovery efficiencies of metal ions with Mn powders increased when the temperature, pH and the concentration of chloride ions were increased in mixed solution. And the recovery efficiencies of Cu was 98% and not changed with the addition amounts of Mn powders but, in case of Co and Ni, the recovery efficiencies were increased with the addition amounts. The particle size of precipitate was about $5\mu\textrm{m}$. From the results of experiment we proposed the two-step cementation process for the recovery of Cu, Ni and Co with Mn powders.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.57-68
• /
• 2014

This study categorizes the distributed sand around coastal area of Jeju volcanic Island into three groups according to their components, and arranges their characteristics. In the case of basic physical properties, the silicate sand has slightly greater specific gravity than general sand, and the carbonate sand with widespread distribution has a lower specific gravity. In the gross, the carbonate sand has poor particle classifying and low uniformity coefficient because carbonate minerals of relatively large grain size are mixed. The relation between compressive strength and components shows conflicting tendency that silicate and carbonate components have positive correlation and negative correlation with compressive strength, respectively. Based on the components ratio of one to one, the sand having low carbonate component ratio is expected to be able to utilize in construction fine aggregate. To compare between square root (ACI 308) and cube root (KCI 2012) of compressive strength at computation of elastic modulus, it is considered to non-dimensional elastic modulus.