• Radiation Oncology Journal
• /
• v.35 no.3
• /
• pp.274-280
• /
• 2017

Purpose: To see the gross tumor volume (GTV) dependency according to the phase selection and reconstruction methods, we measured and analyzed the changes of tumor volume and motion at each phase in 20 cases with lung cancer patients who underwent image-guided radiotherapy. Materials and Methods: We retrospectively analyzed four-dimensional computed tomography (4D-CT) images in 20 cases of 19 patients who underwent image-guided radiotherapy. The 4D-CT images were reconstructed by the maximum intensity projection (MIP) and the minimum intensity projection (Min-IP) method after sorting phase as 40%-60%, 30%-70%, and 0%-90%. We analyzed the relationship between the range of motion and the change of GTV according to the reconstruction method. Results: The motion ranges of GTVs are statistically significant only for the tumor motion in craniocaudal direction. The discrepancies of GTV volume and motion between MIP and Min-IP increased rapidly as the wider ranges of duty cycles are selected. Conclusion: As narrow as possible duty cycle such as 40%-60% and MIP reconstruction was suitable for lung cancer if the respiration was stable. Selecting the reconstruction methods and duty cycle is important for small size and for large motion range tumors.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.1
• /
• pp.129-137
• /
• 2017

When the micro-Doppler (MD) image of a ballistic missile is derived, the translational motion compensation (TMC) method is usually applied to the inverse synthetic aperture radar (ISAR) image, but yields poor results because of the micro-motion of the ballistic missile. This paper proposes an efficient TMC method to obtain a focused MD image of a ballistic missile engaged in complicated micro-motion. During range alignment, range profiles (RPs) are coarsely aligned by using the 1D entropy cost function of RPs as a mark, then the coarsely-aligned RPs are fine-aligned by using the minimum 2D entropy of the MD image. During phase adjustment, the gradient of the phase error is appropriately weighted and added to the previous phase error to further fine-tune the aligned RPs. In simulations using the point scatterer model and the measured data from the real missile model, the proposed method provided better image focus than the existing method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.5
• /
• pp.1700-1716
• /
• 1996

The two-dimensional, unsteady, laminar conservation equations for mass, momentum, energy and species transport in the gas phase and mass, momentum and energy in the liquid phase are solved simultaneously in spherical coordinates in order to study heating and vaporization of a droplet entrained in the oscillating flow. The numerical solution gives the velocity and temperature distribution in both gas and liquid phase as a function of time. When the gas flow oscillates around an vaporizing droplet, the liquid flow circulates in the clockwise or counterclockwise direction and the temperature distribution in the liquid phase changes its shapes, depending on the gas fow direction. When the gas flow changes its direction of circulating liquid flow is opposite to the gas flow, forming two vortex circulating in the opposite direction. During the heating period, the difference in the maximum and minimum temperature is large, followed by the almost uniform temperature slightly below the boiling temperature. The mass and heat transfer from the droplet depend on the droplet temperature, droplet diameter and the magnitude of relative velocity, giving the droplet lifetime different from the d$^{2}$-law.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.4
• /
• pp.259-264
• /
• 2017

Spectrally resolved interferometry (SRI) is an attractive technique to measure absolute distances without any moving components. In the spectral interferogram obtained by a spectrometer, the optical path difference (OPD) can simply be extracted from the linear slope of the spectral phase. However, SRI has a fundamental measuring range limitation due to maximum and minimum measurable distances. In addition, SRI cannot distinguish the OPD direction because the spectral interferogram is in the form of a natural sinusoidal function. In this investigation, we describe a direction determining SRI and propose the optimal conditions for determining OPD direction. Spectral phase nonlinearity, caused by a dispersive material, effects OPD direction but deteriorates spectral interferogram visibility. In the experiment, various phase nonlinearities were measured by adjusting the dispersive material (BK7) thickness. We observed the interferogram visibility and the possibility of direction determination. Based on the experimental results, the optimal dispersion conditions are provided to distinguish OPD directions of SRI.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.12
• /
• pp.663-672
• /
• 2017

Building information modeling (BIM) technology based on 3D modeling has been applied to the entire domestic construction industry since 2010. It can calculate quantity take-off considering construction productivity at design phase. Based on this, it is possible to improve the reliability of construction cost prediction of design phase in the process of cost estimation. However, Building Information Level (BIL) defined by Ministry of Land, Infrastructure and Transport and Public Procurement Service does not seem to offer doable environment due to the lack of detailed application items. By calculating construction cost that meets Construction Cost Estimate Accuracy by American Association of Cost Engineers (AACE) through quantity take-off and cost estimation based on 3D modeling of BIM technology, a BIL improvement proposal at design phase for Mechanical Contracts and Construction is provided here. Results showed that properties including outline and minimum specification of the main equipment, internal main piping, and internal main duct should be defined from the intermediate design phase to have reliable cost estimation.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.124-126
• /
• 2008

Grid Connected inverter is produced current to deliver power to grid. To provide low THD current, LCL filters is effective to filter high frequency component of current output from inverter. To provide sinusoidal waveform, there are many researchers have been proposed several controllers for grid-connected inverter controllers. Synchronous Reference Frame (SRF)-based controller is the most popular methods. SRF-based controller is capable for reducing both of zero-steady state error and phase delay. But SRF based controller is contained cross-coupling components, which generate some difficulties to analyze. In this paper, SRF based controller is analyzed. By applying decoupling control, cross-coupling component is eliminated and single phase model of the system is obtained. Through this single phase model, gain controller is designed. To reduce steady state error, proportional gain is set as high as possible, but it may produce instability. To compromise between a minimum steady state error and stability, the single phase model is evaluate through Root Locus and Bode diagram. PSIM simulation is used to verify the analysis.

• Journal of the Korean Society of Systems Engineering
• /
• v.14 no.2
• /
• pp.41-48
• /
• 2018

This paper describes the systems engineering development process for the Departure from Nucleate Boiling Ratio (DNBR) algorithm using FPGA. Current Core Protection Calculator System (CPCS) requirement and DNBR logic are analyzed in the reverse engineering phase and the new FPGA based DNBR algorithm is designed in the re-engineering phase. FPGA based DNBR algorithm is developed by VHSIC Hardware Description Language (VHDL) in the implementation phase and VHDL DNBR software is verified in the software Verification & Validation phase. Test cases are developed to perform the software module test for VHDL software modules. The APR 1400 simulator is used to collect the inputs data in 100%, 75%, and 50% reactor power condition. Test input signals are injected to the software modules following test case tables and output signals are compared with the expected test value. Minimum DNBR value from developed DNBR algorithm is validated by KEPCO E&C CPCS development facility. This paper summarizes the process to develop the FPGA-based DNBR calculation algorithm using systems engineering approach.

• Journal of Advanced Navigation Technology
• /
• v.10 no.3
• /
• pp.235-249
• /
• 2006

In this paper, SER(Symbol Error Rate) variation and effects on SER by phase noise at various frequency offset of the local oscillator in digital communication systems are gerneralyzed for QPSK(Quadrature Phase Shift Keying), MQAM(M-ary Quadrature Amplitude Modulation), OFDM(Orthogonal Frequency Division Multiplex)-MQAM, OFDM-QPSK and 8-VSB(Vestigal Side Bands) modulation methods and compared those with the ideal cases, which have no phase noise, through the MATLAB simulation. And the ration between modulation bandwidths and the SER on the various frequency offsets on the above modulation methods have been analyzed for the system requirement of minimum phase noise characteristics. From this study, we have confirmed that the most sensitive modulation method on the phase noise is OFDM-MQAM and that the relatively insensitive method 8-VSB.

• Journal of Astronomy and Space Sciences
• /
• v.23 no.2
• /
• pp.117-126
• /
• 2006

The Diurnal variation of galactic cosmic ray (GCR) flux intensity observed by the ground Neutron Monitor (NM) shows a sinusoidal pattern with the amplitude of $1{\sim}2%$ of daily mean. We carried out a statistical study on tendencies of the local times of GCR intensity daily maximum aad minimum. To test the influences of the solar activity and the location (cut-off rigidity) on the distribution in the local times of maximum and minimum GCR intensity, we have examined the data of 1996 (solar minimum) and 2000 (solar maximum) at the low-latitude Haleakala (latitude: 20.72 N, cut-off rigidity: 12.91 GeV) and the high-latitude Oulu (latitude: 65.05 N, cut-off rigidity: 0.81 GeV) NM stations. The most frequent local times of the GCR intensity daily maximum and minimum come later about $2{\sim}3$ hours in the solar activity maximum year 2000 than in the solar activity minimum you 1996. Oulu NM station whose cut-off rigidity is smaller has the most frequent local times of the GCR intensity maximum and minimum later by $2{\sim}3$ hours from those of Haleakala station. This feature is more evident at the solar maximum. The phase of the daily variation in GCR is dependent upon the interplanetary magnetic field varying with the solar activity and the cut-off rigidity varying with the geographic latitude.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.74-80
• /
• 2006

This work presents a novel architecture of phase locked loop (PLL) with the current compensating scheme to improve phase noise performance. The proposed PLL has two Charge Pump (CP), main-CP (MCP) and sub-CP (SCP). The smaller SCP current with same time duration but opposite direction of UP/DN MCP current is injected to the loop filter (LF). It suppress the voltage fluctuation of LF. In result, it improves phase noise characteristic. The Proposed PLL has been fabricated with 0.35fm 3.3V CMOS process. Measured phase noise at 1-MHz offset is -103dBc/Hz resulting in a minimum 3dBc/Hz phase noise improvement compared to the conventional PLL.