• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.272-283
• /
• 2017

In this paper, an improved predictive functional control (PFC) scheme for permanent magnet synchronous motor (PMSM) control system is proposed, on account of the standard PFC method cannot provides a satisfying disturbance rejection performance in the case of strong disturbances. The PFC-based method is first introduced in the control design of speed loop, since the good tracking and robustness properties of the PFC heavily depend on the accuracy of the internal model of the plant. However, in orthodox design of prediction model based control method, disturbances are not considered in the prediction model as well as the control design. A minimum-order observer (MOO) is introduced to estimate the disturbances, which structure is simple and can be realized at a low computational load. This paper adopted the MOO to observe the load torque, and the observations are then fed back into PFC model to rebuild it when considering the influence of perturbation. Therefore, an improved PFC strategy with torque compensation, called the PFC+MOO method, is presented. The validity of the proposed method was tested via simulation and experiments. Excellent results were obtained with respect to the speed trajectory tracking, stability, and disturbance rejection.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.6A
• /
• pp.510-516
• /
• 2005

In this paper, we discuss parameters of line code and simulate a same optical ethernet having minimum bandwidth(MB810) and non-minimum bandwidth line code(8B/10B) to present the possibility of improving of transmission performance using minimum bandwidth line code on the high speed optical ethernet. We design the high speed optical ethernet using Serial type LAN PHY 10GBASE-E(WDM type LAN PHY 10GBASE-LX4) for the single(multi) channel link. To compare the transmission performance of MB810, 8B/10B line code we measure the bit error rate(BER) according to the received optical power of single and multi channel link.

• Journal of the Korean Society of Safety
• /
• v.34 no.5
• /
• pp.132-138
• /
• 2019

Fall accident is the most frequent accident type of occupational accidents. As the age of workers increases, trip and fall accident increases more than other types of occupational accident in the middle-aged group. In this study, the gait characteristics of 25 middle-aged participants (mean ages 47.4, S.D. 5.8) were studied to analyze the trip and fall risks. The Minimum toe clearance(MTC) against the floor surface was measured in the variable conditions of gait speed by a motion capture system. In the 50s age group, the MTC decreased and the MTC tended to reduce the variation with increasing walking speed in the level walking. Therefore, the trip and fall risks for the 50s age group is higher than the 40s age group. Especially, the faster walking speed will increase the trip and fall risks even more.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2217-2220
• /
• 1997

To achieve the high performance speed control of synchronous permanent magnet motor, the influence of iron loss can not be negleced as the increase of driving frequency with high speed operation. This paper proposes a maximum efficiency control algorithm for permanent magnet synchonous motors by controlling the d-axis component of the armature current at any speed and torque. The objective of the optimum efficiency controller is to seek a combination of d-q axis current components which provide minimum input power (minimum losses) at a certain operating point by adding a small amout of perturbation to the d-axis current reference.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.244-247
• /
• 2003

This paper is proposed to position and speed control of interior permanent magnet synchronous motor(IPMSM) drive without mechanical sensor. A minimum order state observer is used for the mechanical state estimation of the motor. The observer was developed based on nonlinear model of IPMSM, that employs a d-q rotating reference frame attached to the rotor. A minimum order state observer is implemented to compute the speed and Position feedback signal. The validity of the proposed sensorless scheme is confirmed by various response characteristics.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.239-242
• /
• 2005

A high speed address recovery technique for AC plasma display Panel(PDP) is proposed. By removing the GND switching operation, the recovery speed can be increased and switching loss due to GND switch also becomes to be reduced. The proposed method is able to perform load-adaptive operation by controlling the voltage level of energy recovery capacitor, which prevents increasing inefficient power consumption caused by circuit loss during recovery operation. Thus, the technique shows the minimum address power consumption according to various displayed images, different from Prior methods operating in fixed mode regardless of images. Test results with 50" HD single-scan PDP(resolution = 1366$\times$768) show that less than 350ns of recovery time is successfully accomplished and about 54% of the maximum power consumption can be reduced, tracing minimum power consumption curves.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.8
• /
• pp.54-63
• /
• 1993

This paper proposes a method for improving the performances of the neural network for optimization by an optimal estimation of initial states. The optimal initial state that leads to the global minimum is estimated by using the stochastic approximation. And then the update rule of Hopfield model, which is the high speed deterministic algorithm using the steepest descent rule, is applied to speed up the optimization. The proposed method has been applied to the tavelling salesman problems and an optimal task partition problems to evaluate the performances. The simulation results show that the convergence speed of the proposed method is higher than conventinal Hopfield model. Abe's method and Boltzmann machine with random initial neuron output setting, and the convergence rate to the global minimum is guaranteed with probability of 1. The proposed method gives better result as the problem size increases where it is more difficult for the randomized initial setting to give a good convergence.

• Tribology and Lubricants
• /
• v.4 no.1
• /
• pp.69-73
• /
• 1988

The effects of journal speed and bearing load on pressure distribution and the temperature distribution of bearing surface are investigated experimentally. The journal bearing which has 219.94mm diameter, length-to-diameter ratio of L/D=0.8 and clearance ratio of 0.004 is used. Journal has a built-in pressure transducer for the measurement of pressure distribution in the mid plane of bearing. Bearing surface temperatures are measured at 60 points. The bearing load is varied from 300 N to 5900 N and journal speed from 300 rpm to 2500 rpm. As the load is increased under constant speed, the location of maximum pressure moves to the site of minimum film thickness, and maximum pressure and absolute value of minimum pressure are increased. The temperature distribution in vicinity of oil inlet shows that heated lubricant's carry-over exists around the oil inlet.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.238-244
• /
• 2004

This research conducted milling tests to study effects of cutting environment conditions of ball end milts on the characteristics of high speed milling cutting process. KP4 steels and STD11 heat treated steels were used as the workpiece and WC-Co ball end mill tools with TiAIN coated were utilized in the cutting tests. Dry cutting without coolant and semidry cutting using botanical oil coolant by the MQL(Minimum Quantity Lubricant) device were conducted. Cutting forces, tool wear and surface roughness were measured in the cutting tests. Results showed that MQL spray cutting of KP4 and hardened STD11 specimens produced better surface quality and wear performance than dry cutting did.

• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.128-131
• /
• 2001

Laser cladding processing allows rapid transfer of heat to the material being processed with minimum conduction into base metal, resulting in low total heat input. The effects of $CO_2$ laser cladding with powder feeding on mechanical properties of VERSAlloy were studied. Their low melting point (under 1093$^{\circ}C$) enables overlays to be applied with minimum dilution and base metal distortion. Experiment results indicated that powder feeding speed and quantity were important for laser cladding with powder feeding. The powder feeding speed should be adapted according to cladding speed for good shaping of clad layer. The effect of heat on the HAZ size can be limited and the growth of grain size of HAZ size was not serious.