• 전기학회논문지P
• /
• 제65권4호
• /
• pp.285-291
• /
• 2016

A light-emitting diode (LED) has been increasingly applied to various industrial fields and general lightings because of its high efficiency, low power consumption, environment-friendly characteristic and long lifetime. To drive the LED lighting, a power converter with the constant output current is needed. Among many power converters, the flyback converter is chosen by many converter designers due to high power density, structural simplicity, and miniaturization. In this converter, an electrolytic capacitor is generally chosen for the stabilization of the DC voltage because of having the large capacitance and the low price. However, the disadvantages are the short expected life time and 120Hz ripple currents on the converter output node. In this paper, a single-stage dimmable PFC DCM flyback converter without the electrolytic capacitor is proposed to prolong the lifetime of the LED driver. For the long lifetime of the converter, the polyester film capacitor with the small capacitance is substituted for the electrolytic capacitor on the output node and an LC resonant filter is added to damp 120Hz ripple current. The proposed converter is verified through the simulation and the experimental works.

• 반도체디스플레이기술학회지
• /
• 제3권3호
• /
• pp.11-17
• /
• 2004

This research has been progressed for adhesive improvement of the Polyimide/Buffer layer/Cu at the COF(Chip On Film) which induced as the alternative plan about high concentration of a circuit or substrates according to demands of miniaturization and high efficiency of various electronic equipment. RF plasma equipment was applied to when plama pretreatment was performed for improvement of adhesive strength of PI and Cr as the buffer layer. Experimental fluents were a species of the buffer layer, depositied time and the ratio of $O_2$/Ar when performed to plasma pretreatment. The results are that Ni was superior to Cr at peel test according to a species of the buffer layer, peel strength and Cu THK were showed proportional relation to deposition structure of the same buffer layer and sample of the Cr depositied time(30 sec) and Cu depositied time(20 min) was showed good adhesion to peel test according to Cr's depositied time and Cu's depositied time. When perform PI's plasma pretreatment peel strength and $O_2$/Ar ratio were showed proportional relation. But $O_2$/Ar(2/5) was best condition since then decreased.

• 한국정보전자통신기술학회논문지
• /
• 제11권4호
• /
• pp.388-393
• /
• 2018

본 논문은 고효율 리플렉터 일체형 50W급 AC 직결형 엔진을 개발하여 SMPS 사용하지 않고 제품의 소형화 및 경량화를 구현하여 소비자가 편리하게 사용하고, AC Driver의 취약한 부분을 보완하기 위해 다단 바리스터 회로를 설계하여 전자 부품 수량 감소를 통한 원가절감 전해 콘덴서를 사용하지 않는 회로 구성으로 고신뢰성을 구현 하여 LED수명을 증대시켰다. 또한 AC 직결형 구동장치를 IC 반도체로 제작하여 리플렉터 일체형으로 AC 직결형 구동장치를 적용 하여 제작 그 수명을 LED의 온전한 수명을 모두 사용할 수 있는 장치와 발광 다이오드 조명 장치의 제어 회로에 하나 이상의 발광다이오드를 포함하는 여러 개의 발광 다이오드 채널이 직렬로 구성되는 광원을 정류 전압으로 구동하는 발광 다이오드 조명 장치의 제어회로를 제안하였다.

• 한국인터넷방송통신학회논문지
• /
• 제21권3호
• /
• pp.35-42
• /
• 2021

초고주파 대역에서 TWTA(Traveling Wave Tube Amplifier)를 대체하기 위한 증폭기 연구가 활발히 이루어지고 있다. 반도체형 소자를 결합하여 높은 출력을 얻는 SSPA(Solid State Power Amplifier)의 경우 상대적으로 낮은 단일 소자의 출력으로 요구 출력을 충족하기 위해서는 저손실, 고효율의 결합 기술이 필요하다. 본 논문을 통해 8-way 도파관 결합기를 설계, 제작하여 20dB 이상의 반사 손실과 85% 이상의 결합 효율을 확인하였다. 전계 분석을 통해 결합기 내부의 임계 전력을 계산하여 안정적인 Power Rating을 확보하였고 전력 모니터링을 위한 커플러를 내장하여 소형화 및 경량화를 이루었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제24권3호
• /
• pp.62-67
• /
• 2022

Liquid hydrogen (LH₂) has a higher density than gaseous hydrogen, so it has high transport efficiency and can be stored at relatively low pressure. In order to use efficient bulk hydrogen in the industry, research for the LH₂ supply system is needed. In the high-pressure hydrogen station based on LH₂ currently being developed in Korea, a heat exchanger is used to heat up supercritical hydrogen at 700 bar and 60 K, which is pressurized by a cryogenic high-pressure pump, to gas hydrogen at 700 bar and 300 K. Accordingly, the heat exchanger used in the hydrogen station should consider the design of high-pressure tubes, miniaturization, and freezing prevention. A helical heat exchanger generates secondary flow due to the curvature characteristics of a curved tube and can be miniaturized compared to a straight one on the same heat transfer length. This paper evaluates the heat transfer performance through parametric study on the distance between coils, guide effect, and anti-icing design of helical heat exchanger. The helical heat exchanger has better heat transfer performance than the straight tube exchanger due to the influence of the secondary flow. When the distance between the coils is uniform, the heat transfer is enhanced. The guide between coils increases the heat transfer performance by increasing the heat transfer length of the shell side fluid. The freezing is observed around the inlet of distribution tube wall, and to solve this problem, an anti-icing structure and a modified operating condition are suggested.

• 센서학회지
• /
• 제27권2호
• /
• pp.99-104
• /
• 2018

A micro electromagnetic actuator with high vibration efficiency is proposed for use in an implantable hearing device. The actuator, which can be implanted in the middle ear, consists of membranes based on the stainless steel 304 (SUS-304), and other components. In conventional actuators, in which a thick membrane and a silicone elastomer are used, the size reduction was difficult. In order to miniaturize the size of the actuator, it is necessary to reduce the size of the actuation potion that generates the driving force, resulting in reduction of the electromagnetic force. In this paper, the electromagnetic actuator is further miniaturized by the metal membrane and the vibration amplitude is also optimized. The actuator designed according to the simulation results was fabricated by using micro-electro-mechanical systems (MEMS) technology. In particular, a $20{\mu}m$ thick metal membrane was fabricated using the erosion process, which reduced the length of the actuator by more than $400{\mu}m$. In the experiments, the vibration displacement characteristics of the optimized actuator were above 400 nm within the range of 0.1 to 1 kHz when a current of $1mA_{rms}$ was applied to the coil.

• 한국산학기술학회논문지
• /
• 제14권11호
• /
• pp.5392-5395
• /
• 2013

환자 및 노약자 이동에 중요한 역할을 하고 있는 수 전동휠체어의 핵심부인 구동부를 새롭게 설계했다. 구동부는 고속모터와 다단기어 치형을 설계적용하고, 굽힘강도와 면압강도를 고려해 큰 추진력을 얻을 수 있도록 성능을 검증하였다. B-Type의 마찰판식 클러치 전자식 브레이크(다판 방식의 무여자 작동형)를 동 축상에 설치해, 큰 토크에도 급격한 제동이 가능하도록 했다. 본 연구에 설계된 다단치차 감속기를 수 전동휠체어 구동장치에 사용하므로서, 소형화, 경량화를 이루고 구동 효율이 기존제품보다 30% 향상된 구동부를 구성할 수 있었으며, 보수 및 관리의 용이성을 함께 추구했다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.223-227
• /
• 2003

In this study, ultrasonic rotary motors using a bolted langevin type ultrasonic vibrator were designed and fabricated. The stator vibrator has a longitudinal transducer section composed of two metal blocks and two piezoelectric ceramic elements (thickness-polarized) and a mode conversion metal block section called a torsion coupler. And, three kinds of motors were studied by finite element analysis and experiments. So, as material of torsion coupler which generate mode conversion of vibration copper, brass, and phosphor bronze were used. As a result, speed and torque were changed in proportion to the electrical input Voltage, but it was saturated in high voltage. And bad efficiency which was different from a expectation was measured in this motors. So, various problems should be improved for practical use. Finally, The motor which has 1 [cm] diameter was fabricated to present a possibility of miniaturization of this type motors.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.559-562
• /
• 2004

The $high-T_c$ Superconducting(HTS) antenna which consists of "H" type resonator has the benefits for the miniaturization of antenna in comparison with the microstrip antenna of the similar dimension. To fabricate the "H" type antenna HTS $YBa_2Cu_3O_{7-x}$(YBCO) thin films were deposited on MgO substrates using rf-magnetron sputtering. Standard etching processes were performed for the patterning of the "H" type antenna. For comparison between normal conducting antennas and superconducting antennas, the gold antennas with the same dimension were also fabricated. An aperture coupling was used for impedance matching between $50\Omega$ feed line and HTS radiating patch. The diverse experimental results were reported in terms of the resonant frequency, the return loss and the characteristics impedance. The "H" type superconducting antenna showed the performance of 1.36 in SWR, 24 % in efficiency, and 14.6 dB in the return loss superior to the normal conducting counterpart.

• 한국산학기술학회논문지
• /
• 제22권5호
• /
• pp.310-316
• /
• 2021

기존의 인공위성은 다기능·높은 성능을 가진 대형위성을 국가 단위에서 운용하는 것이 일반적이었으나 최근의 전기·전자 및 광학 기술의 경량 소형화 발전에 따라 점차 소형위성이 주목받고 있다. 크기와 무게가 감소됨에 따라 적은 비용으로 개발 및 발사가 가능하여 위성 개발에 진입장벽이 낮아지고 있으나, 인공위성의 전력공급에 필수적인 태양전지 패널의 경우 태양광에 효율적으로 노출되기 위해 넓은 표면적이 필요하여 소형화 및 경량화가 제한적이다. 우주용 태양전지는 우주선과 태양열, 온도와 같은 다양한 우주환경을 고려하여 제작되어야하고, 부피를 최적화하기 위해 전개 매커니즘을 적용하며 경량화 및 고효율화를 위하여 태양전지 셀의 구조적 재료적인 연구개발이 필요하다. 현재 태양전지 패널로 개발되어 운용되고 있는 제품들은 고효율화를 위하여 주로 InGaP/GaAs/Ge 소재의 3중구조를 적용하고 있다. 최근에는 초고효율 다층구조 태양전지를 위하여 4중접합 이상의 구조가 연구되고 있으며, 나아가 소재적으로 경량화에 유리한 유연박막 태양전지, 유기 및 유무기 하이브리드 태양전지 등이 차세대 소형위성용 태양전지로 주목받고 있다.