• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.104-110
• /
• 2003

As exhaust emission standards are more stringent, higher conversion efficiency of automotive catalytic converter is required. In addition, catalytic converter is deteriorated during mileage accumulation of vehicle. Therefore the specification of catalytic converter should be decided in consideration of emission standards and deterioration. Because the decision of the specification of catalytic converter is required at the beginning of vehicle development procedure, it is important and necessary to fix the target values of green vehicle exhaust emissions. To do this, a linear regression analysis was done with in-use exhaust emissions data of 5 different kinds of vehicle that received US94 emission standards certification, and data handling methods including some statistical estimation were proposed. As a result, the fixed target values of NMHC, CO, NOx of green vehicle against US94 emission standards were 0.079, 0.83, 0.116, respectively. And expected in-use deterioration factor of NMHC, CO, NOx were 1.75, 2.02, 1.38, respectively. And also it was blown that even if failure rate is 30% after 80,000km driven, it might be sufficiently safe from emission failure confirmatory test of Korea. It is hopeful to make a database of in-use emissions to increase the confidence in correctness of the calculated target values.

• Journal of ILASS-Korea
• /
• v.21 no.3
• /
• pp.137-143
• /
• 2016

The LPG vehicles are being operated by commercial purposes generally such as taxis. Most of taxis have a long-mileage and a harsh driving pattern. These properties may accelerate aging of the three-way catalysts much faster than the passenger vehicles. Because of this background, it was analyzed the test result of fuel efficiency and emissions on the LPG-fueled light duty vehicle. It was selected for a LPG vehicle of ULEV level to measure the fuel efficiency and emissions of the aged three-way catalysts. And the aged three-way catalysts which was driven about 300,000km and 550,000km replaced on the test vehicle in consecutive order. As a result, The aged three-way catalysts generally had no effect on fuel efficiency result, and harmful exhaust emissions had been shown to increase in most of the test mode, even though it satisfied the regulation value on most test modes.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.30 no.1
• /
• pp.25-32
• /
• 2007

Automobile manufacturing companies should provide the products and service that can satisfy consumers who usually want various kinds of automobiles. This paper studied the relations among several demographic characteristics(gender, age, occupation, income) of consumers and automobile's attributes(engine performance, engine displacement, price, maintenance expenses, color, etc.) and preferred automobile(kind, size, company, price). For the relation research we established a model and related hypotheses and used a questionnaire survey, where 350 subjects were questioned. After the analysis, many statistically significant results are obtained : consumer's gender has relations with the preference for engine performance, engine displacement, price, color, and design; age has relations with the preference for engine displacement, maintenance expenses, free checking during A/S period, etc., occupation has relations with the preference for engine performance, engine displacement, price, maintenance expenses, fuel efficiency, etc. : income has relations with the preference for engine performance, engine displacement, price, maintenance expenses, mileage, reputation of car manufacturing companies, etc.; price and fuel efficiency has relations with the preference for car manufacturing companies. These results suggest the consumer-oriented sales of automobiles and are expected to be helpful for the effective strategy development of automobile marketing.

• Journal of the Korean Society for Railway
• /
• v.16 no.2
• /
• pp.93-98
• /
• 2013

Railway system is today the most efficient way for transportation in many cases in several forms of application. Yet, wear phenomenon, profile evolution, fatigue, fracture, derailment are the major worries (financial and safety) in this system which force significant direct and indirect maintenance costs. To improve the cyclic maintenance procedures and the safety issues, it can be very satisfactory to be informed of the state of wheel/rail interaction with mileage. In present paper, an investigation of the behavior of the shear stresses by logged distance is approached, by implementing the field measurement procedure, in order to determine the real conduct of the most important cause of defects in wheel/rail contact, shear stress. The results coming from a simulation procedure indicate that the amounts of shear stresses are still in high-magnitudes when the wheel and rail are completely worn; even though in simulation based on the laboratory measurements of profile evolutions, the stresses become significantly reduced by logged distance.

• Journal of the Korean Society of Safety
• /
• v.24 no.4
• /
• pp.1-10
• /
• 2009

The characteristics of smoke emissions from diesel heavy duty vehicles which weigh over 5.5 tons was investigated by driving the vehicles with both the Lugdown 3 modes in the chassis dynamometer and tree accelerating mode under no load. The vehicles include commercial vehicles such as bus, microbus, trucks and specialized vehicles, etc. The total numbers of the vehicles tested were 200. The light extinction method was used to measure the smoke emissions from the vehicles tail pipe. The values of the smoke emissions in the tree accelerating mode showed $0{\sim}20%$ band nearly independent of both the mileage and year of production of the tested vehicles, while those in the Lugdown 3 modes showed $0{\sim}99%$ of wide band. The correlation coefficients between the values of the smoke emissions with both the Lugdown 3 modes and the free acceleration mode were 0.12, 0.08, 0.12, respectively. The inspection with Lugdown 3 modes is better one than that with tree acceleration from the point of exact inspection of the diesel vehicles' smoke emission.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.5
• /
• pp.212-217
• /
• 2012

High strength steel sheets used for automobile outer-panels have been intensively studied for developing a lightweight automobile under a strong pressure of the requirements for enhancing the mileage and energy saving in production of automobile parts. It is known that high strength steels are susceptible to hydrogen embrittlement, The susceptibility to hydrogen embrittlement increases with increasing its strength. However, the effect of hydrogen on the fracture behavior of high strength steels, though investigated extensively, has not been fully understood. In this paper, hydrogen was charged with 590DP steels by electrochemical method and its content was measured by hydrogen determinator with the different charging conditions. It was shown that the SP energy and maximum load decreased with increasing charging time. The results of SEM-fractography investigation for the hydrogen contained samples showed that a small portion of dimples on cleavage-fractured surface were observed and the size of the dimples were decreased with increasing hydrogen charging time.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.847-849
• /
• 2009

Usually, after the decisions of the performance and range in the commercial vehicle, it is designed the ratings of the electric and mechanical elements for the vehicles. In this paper, the given performance and driving conditions, which are the maximum velocity, mileage, total weight of the normal gasoline scooter, battery type and size, and so on, are analysed for the design of the electric scooter. The maximum rotational speed and needed torque values of the electric motor which is substituted for the gasoline engine are calculated. These values can help to calculate the rating of the electric motor. In the calculation to obtain the torque and speed values, battery discharge and the running resistances are considered. We can decide the electric motor current value from the torque and speed values. The electric motor current values, which are significant parameter to decide the motor type and dimensions and characteristics of the electric motor, are decided by numerical simulation by the above conditions.

• Interaction and multiscale mechanics
• /
• v.4 no.1
• /
• pp.35-47
• /
• 2011

A global-local finite element modeling technique is employed in this paper to predict the fatigue life of radial truck tires. This paper assumes that a flaw exists inside the tire, in the local model. The local model uses an FEM fracture analysis in conjunction with a global-local technique in ABAQUS. A 3D finite element local model calculates the energy release rate at the belt edge. Using the analysis of the local model, a study of the energy release rate is performed in the crack region and used to determine the crack growth rate analysis. The result considers how different driving conditions contribute to the detrimental effects of belt separation in truck tire failure. The calculation of the total mileage on four sizes of radial truck tires has performed on the belt edge separation. The effect of the change of belt width design on the fatigue lifetime of tire belt separation is discussed.

• Journal of the Korean Society for Railway
• /
• v.15 no.3
• /
• pp.224-230
• /
• 2012

The wearing slider of the rail motor car's pantograph is considerable changed by the type and the material properties. Especially, precipitation and arc influences are main factors decided to life time of wearing slider and contact wire. This study is wearing phenomenon analysis of Cu-type wearing slider with high electric conductivity and resistance arc through experiment by running train. Author observed that wearing phenomenon of Cu-type wearing slider with normal and abnormal wearing characteristics and comparatively analysis precipitation, mileage and weight influences of exchanged Cutype and Fe-type wearing sliders. In this paper result showed that necessity for the application which is the Fe-type of wearing slider had superior wear resisting capacity etc., through tribology approach.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.666-672
• /
• 2008

Train wheels are the most important part of the high-speed rail system with supporting body, running stably and safely. Wheel exchange and fix plan is computed by the worker who managing entire Train Maintenance Process based on his know-how so that this system is losing its reliability and accuracy. And predicting of the wheel's lifetime is absolutely difficult matter because of uncertainty between trains like mileage of the type of trains, condition of operation, curve section and wheel's cutting pattern. Therefore workers always used to hold many wheels. For this reason, the cost of stock is soar when the level of stock was normal. If the stock is sufficient, the cost of stock will rise. On the other hand, If the stock is deficient, we would have trouble that the plan of the train maintenance process will be failed. Thus this paper aimed at application that "Wheel Managing System" which is able to predict wheel's life-cycle and demands under the RIMS(Rolling-Stock Information Maintenance System) with analysing wheel exchanging and cutting status considering economical or stable aspects.