• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1721-1727
• /
• 1989

Carbon-ferrite microwave absorbers were designed experimentally and fabricated trialy, as a result of which the relative frequency bandwith of 7.3 to 8.2% were obtained under the tolerance limits of the reflection coefficients lower than -20 dB, and the matching thickness becomes 1.4 to 1.6mm, which is significantly thinner than that of the conventional ones. Furthermore, attenuation has been founded by measuring the material constants of the microwave absorbers for microwave oven and the results are compared and discussed.

• Korean Journal of Materials Research
• /
• v.11 no.11
• /
• pp.941-946
• /
• 2001

Conductive microspheres with a density of 0.2 g/cc were fabricated by electroless silver plating for application to the light-weighted microwave absorbers. The silver plating was conducted with the variation of plating conditions (sensitizing condition, $AgNO_3$, concentration, amount of reducing agent). Specimens have very low electro-resistivity. Under an optimum processing condition, conductive microspheres with uniform silver plating layer can be produced. Rubber-sphere composites were fabricated and their microwave absorbing properties were measured by HP8722D Network Analyzer. It was found that the lower the electrical resistance of microsphere, the better the microwave absorbing properties. Feasibility of microwave absorbers using this microspheres can be demonstrated with the result of microwave reflection loss of -15 dB and thickness of 1.44 mm.

• Journal of the Korean Institute of Navigation
• /
• v.15 no.1
• /
• pp.1-9
• /
• 1991

The coaxial sample holder with 20mm in diameter and the adaptor from type N connector-to-20mm${\phi}$ coaxial tube are designed and manufactured which have been used for designing and measuring the fabricated microwave absorber. In addition, the measure in method of material constants of the microwave absorbers is described, which is focused on minimizing the error due to the sample's shapes, the fitting conditions, etc. After describing the design method of a single-layed microwave absorber, the microwave absorbers for X-band, C-band and S-band RADARs are designed and fabricated, respectively, which are composed of ferrite, carborn, and binder and have good performance. Futhermore, we develop the high performance microwave absorber in extremely wide-band type for RADAR, which is composed of different material and its mixing ratio and which could cover nearly from 4 to 10 GHz.

• Korean Journal of Materials Research
• /
• v.12 no.6
• /
• pp.442-446
• /
• 2002

Design of microwave absorbers using high frequency properties of fiber reinforced composites are investigated. Two kinds of composite materials (glass and carbon) are used and their complex permittivity and permeability are measured by transmission/reflection technique using network analyzer. Low dielectric constant and nearly zero dielectric loss are determined in glass fiber composite. However, carbon fiber composites show the high dielectric constant and large conduction loss which is increased with anisotropy of fiber arrangement. It is, therefore, proposed that the glass and carbon fiber composites can be used as the impedance transformer (surface layer) and microwave reflector, respectively. By inserting the foam core or honeycomb core (which can be treated as an air layer) between glass and carbon fiber composites, microwave absorption above 10 dB (90% absorbance) in 4-12 GHz can be obtained. The proposed fiber composites laminates with sandwitch structure have high potential as lightweight and high strength microwave absorbers.

• Korean Journal of Materials Research
• /
• v.13 no.4
• /
• pp.259-265
• /
• 2003

For the aim of thin microwave absorbers used in mobile telecommunication frequency band, this study proposed a high permittivity dielectrics(λ/4 spacer) coated with ITO thin films of 377 $\Omega$/sq(impedance transformer). High frequency dielectric properties of ferroelectric ceramics, electrical properties of ITO thin films and microwave absorbing properties of ITO/dielectrics were investigated. Ferroelectric materials including $BaTiO_3$(BT), 0.9Pb($Mg_{1}$3/Nb$_{2}$3/)$O_3$-0.1 $PbTiO_3$(PMN-PT), 0.8 Pb (Mg$_{1}$3/$Nb_{2}$3/)$O_3$-0.2 Pb($Zn_{1}$3$_Nb{2}$3/)$O_3$(PMN-PZN) were prepared by ceramic processing for high permittivity dielectrics,. The ferroelectric materials show high dielectric constant and dielectric loss in the microwave frequency range. The microwave absorbance (at 2 ㎓) of BT, 0.9PMN-0.1PT, and 0.8PMN-0.2PZN were found to be 60%(at a thickness of 3.5 mm), 20% (2.5 mm), and 30% (2.5 mm), respectively. By coating the ITO thin films on the ferroelectric substrates with λ/4 thickness, the microwave absorbance is greatly improved. Particularly, when the surface resistance of ITO films is closed of 377 $\Omega$/sq, the reflection loss is reduced to -20 ㏈(99% absorbance). This is attributed to the wave impedance matching controlled by ITO thin films at a given thickness of high permittivity dielectrics of λ/4 (3.5 mm for BT, 2.5 mm for PMN-PT and PMN-PZN at 2 ㎓). It is, therefore, successfully proposed that the ITO/ferroelectric materials with controlled surface resistance and high dielectric constant can be useful as a thin microwave absorbers in mobile telecommunication frequency band.

• Korean Journal of Materials Research
• /
• v.12 no.2
• /
• pp.160-165
• /
• 2002

High-frequency dielectric and microwave absorbing properties have been investigated in ferroelectric materials (BaTiO$_3$(BT), (1-x)Pb$Mg_{\frac{1}{3}}Nb_{\frac{2}{3}}$)O$_3$-xPbTiO$_3$(PMN-PT), (1-x)Pb$Mg_{\frac{1}{3}}Nb_{\frac{2}{3}}$O$_3$-xPb(Zn_{\frac{1}{3}}Nb_{\frac{2}{3}}$)O$_3$(PMN-PZN) for the aim of thin microwave absorbers in the frequency range of mobile telecommunication. The specimenns are prepared by conventional ceramic processing and complex permittivity has been measured by transmission/reflection method. The ferroelectric materials show high dielectric constant and dielectric loss in the microwave range and their domiant loss mechanism is considered to be domain wall relaxation. The microwave absorbance of BT 0.9PMN-0.1PT, and 0.8PMN-0.2PZN specimen (determined at 2) are found to be 99.5% (at a thickness of 4.5 mm), 50% (2.5 mm), and 30% (2.5 mm), respectively. It is suggested that PMN-PT or PMN-PZN ferroelectrics are good candidate materials for the spacer of λ/4 absorber. The use of ferroelectric materials is effective in reducing the thickness of absorber with their advantage of high dielectric constant.

• Journal of Navigation and Port Research
• /
• v.29 no.2
• /
• pp.147-150
• /
• 2005

We suggest a cast Alnico magnet as a new microwave absorber. The proposed Alnico microwave absorber shows advanced microwave absorption properties of 24 dB at 13.3 GHz for the thicknesses of 1 mm We also investigated the effects of the carbon, which qjfects strongly to microwave absorption in Alnico magnet microwave absorbers. Central frequency shifts toward lower frequency with increasing Alnico content which is related to the frequency to show tan 8 > 1. Also, we investigated the sample thickness dependence on the microwave absorption properties.

• Journal of electromagnetic engineering and science
• /
• v.19 no.2
• /
• pp.71-81
• /
• 2019

This paper presents a design methodology for wideband single-layered microwave absorbers with arbitrary absorption at the design center frequency using reactive Salisbury screens. The bandwidth of the absorber increases when the flatness of the reflection response at the design center frequency is maximized. Based on this observation, closed-form design formulas for wideband absorbers are derived. As they are scalable to any design frequency, wideband reactive screens can be systematically realized using two-dimensional periodic crossed-dipole structures patterned on a resistive sheet. Based on this method, a single-layered absorber with a 90% bandwidth improved to 124% of the design center frequency is presented. For the purpose of physical demonstration, an absorber with a design center frequency of 10 GHz is designed and fabricated using a silver nanowire resistive film with a surface resistance of 30 Ω/square. The measured absorption shows a good agreement with both the calculation and the electromagnetic simulation.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1993.03a
• /
• pp.48-49
• /
• 1993

• Korean Journal of Metals and Materials
• /
• v.50 no.5
• /
• pp.389-393
• /
• 2012

Improvement in microwave absorbance has been investigated by insertion of a periodic air cavity in rubber composites filled with magnetic powders. A mixture of $Co_2Z$ hexagonal ferrite and Fe powders were used as the absorbent fillers in silicone rubber matrix. The complex permeability and complex permittivity of the magnetic composites were measured by reflection/transmission technique. In the grid-type magnetic absorbers, the equivalent permeability (${\mu}_{eq}$) and permittivity (${\varepsilon}_{eq}$) are calculated as a function of air volume rate (K) on the basis of effective medium theory. Reduction in the material parameters (especially, dielectric permittivity and magnetic loss) has been estimated with the increase of K. Plotting the ${\mu}_{eq}$ and ${\varepsilon}_{eq}$ on the solution map of wave-impedance matching, wide bandwidth microwave absorbance has been predicted in the magnetic composites with an optimum value of K.