• The korean journal of orthodontics
• /
• v.15 no.2
• /
• pp.261-269
• /
• 1985

The purpose of this study was to measure and compare tensile strength for 3 types of new direct-bond brackets and the same brackets after recycling and to evaluate recycled brackets to determine the extent of physical alteration after recycling. Three types of new direct-bond brackets were bonded to recently extracted human premolar teeth and the tensile strength was measured by Universal Testing Machine. The brackets were recycled by thermal process and the tensile test was repeated. To determine the extent of physical alteration after recycling, the slot width and the hardness of metal brackets were measured and to analyze the microstructure of the brackets, photographs of the bracket microstructure were taken. Following results were obtained: 1. The tensile strength of recycled brackets was lower than that of new brackets, but there was no statistically significant difference. (p>0.05) 2. In the new and recycled brackets, the tensile strength of mini-mesh base bracket was statistically higher than that of conturlok base bracket, $(p\leq0.05)$ but there was no statistically significant difference between production of other companies. (p>0.05) 3. The slot width of metal bracket was enlarged from 0.459mm to 0.469mm as a result of the recycling process. (p>0.005) 4. As temperature was increased in thermal treatment, the grains of bracket metal gradually became coarser and the hardness was decreased.

• Journal of the Mineralogical Society of Korea
• /
• v.13 no.2
• /
• pp.53-64
• /
• 2000

Chlorite from the talc deposits in the Chungnam area, Korea, has been studied using electron microprobe analysis and high resolution transmission electron microscopy (HRTEM), Talc orea are hydrothermal alteration products of serpentinite which was originated from ultramafic rocks. Chlorite occurs in close association with talc ores of with the black alteration zone between talc ore bodies and granitic gneiss. It is the most abundant impurity mineral of talc ores. Chlorite in association with talc is characterized by very high but narrow variation in Mg/(Mg+Fe) ratios (0.784~0.951), significant octahedral substitution (-0.200~0.692), wide variation in Al contents (1.085~3.160 / 14 oxygens), and high Cr and Ni contents. It was formed under a very limited but high Mg/(Mg+Fe) condition in close connection with serpentinite. Chlorite in the black alteration zone is characterized by a high Fe content, wide variation in Mg/(Mg+Fe) ratios (0.378~0.852), narrow octahedral substitution (-0.035~0.525), high narrow Al contents (1.468~2.959), and low Cr and Ni contents. It was formed under a low Mg/(Mg+Fe) and relatively Al-rich condition in close connection with county rocks. Two different chemical modes for chlorite suggest two different origins for two different chlorites. Although most of chlorites show typical 14-$\AA$ lattice fringe images under HRTEM, some chlorites show fringe images of 21-$\AA$ (14$\AA$+7$\AA$) spacings within (001) lattice-fringe images of chlorite (14$\AA$). But brown chlorite from the black zone has high Ti and K contents suggesting that mica was the precursor of brown chlorite. Such possibility is also supported by the fact that lattice-fringe images of brown chlorite show 14-$\AA$ chlorite layers in which 10-$\AA$ mica single layer or packets are interlayered. Partial terminations from 3 mica layers to 2 chlorite layers are often observed. It, therefore, is suggested that the chlorite associated with talc ores is a hydrothermal alteration products of serpentinite, whereas the chlorites in the black alteration zone is a hydrothermal alteration product of granitic gnesis under a partial influence of serpentinite.

• Journal of Periodontal and Implant Science
• /
• v.38 no.1
• /
• pp.67-74
• /
• 2008

Purpose: The aim of this study was to evaluate the effect of Er:YAG laser on microstructure and roughness of $TiO_2$ blasting implant surface. Materials and Methods: Ten $TiO_2$ blasting implant were used in this experiment. One implant was control group, and nine $TiO_2$ blasting implant surfaces were irradiated with Er:YAG laser under 100 mJ/pulse, 140 mJ/pulse, and 180 mJ/pulse condition for 1 min, 1.5 min, and 2 min respectively. Optical interferometer and scanning electron microscopy was utilized to measure roughness and microstructure of specimens. Results: The surface roughness was decreased after Er:YAG laser irradiation in all groups, but there was no significant difference. 100 mJ/pulse and 140 mJ/pulse group did not alter the $TiO_2$ blasting implant surface in SEM study while 180 mJ/pulse group altered the $TiO_2$ blasting implant surface. Implant surfaces showed melting, microfracture and smooth surface in 180 mJ/pulse group. Conclusion: Detoxification of implant surface using Er:YAG laser must be irradiated with proper energy output and irradiation time to prevent implant surface alteration.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.287-290
• /
• 2005

Once hot forgings for automotive parts such as wheel bearing flange to which cyclic asymmetric bending stress is continuously applied are produced, it is necessary to control their microstructure to obtain superior mechanical properties. It is however hard to control the microstructure uniformly because the strength is reduced as coarsening of ferrite grains. To investigate the microstructural alteration according to process variables during hot working, the variation of the ferrite grain size was studied by utilizing of the computer aided servo-hydraulic Gleeble tester which is hot deformation behavior reproduction equipment. In addition, the effect of the ferrite grain size of raw material on the austenite grain behavior of hot forgings was also examined. The rolling contact fatigue resistance of the induction hardened SAE 1055 steel was compared with the occasion of the same condition of SAE52100 bearing steel. As a result, it was confirmed that the ferrite grain sizes of the forgings depend on the heating temperature and cooling start temperature during hot forging and cooling processes. The induction hardened SAE1055 steel showed a superior rolling contact fatigue resistance to the induction hardened SAE52100 steel. The reason is that SAE1055 steel is freer from the material defect such as segregation than the comparative steel.

• Journal of the Korean Ceramic Society
• /
• v.49 no.1
• /
• pp.48-55
• /
• 2012

Degradation of performance and life time of a functional material or device thereof is induced, to a great extent, by mass transfer in the material that is driven by various thermodynamic forces imposed intentionally or accidentally during its operation or service. The forces are any gradient of intensive thermodynamic variables, component chemical potentials, electrical potential, temperature, stresses, and the like. This paper reviews electric-field induced degradation phenomena in ionic solid compounds including insulation resistance degradation, crystal shift, microstructural alterations, compositional unmixing, and compound decomposition. Their inner workings are also discussed qualitatively.

• Journal of Periodontal and Implant Science
• /
• v.36 no.3
• /
• pp.705-716
• /
• 2006

The present study was performed to evaluate the effect of tetracycline-HCl on the change of implant surface microstructure according to application time. Implant with pure titanium machined surface, GBA surface and RBM surface were utilized. Implant surface was rubbed with 50mg/ml tetracycline-HCl solution for ${\frac{1}{2}}$min. 1min. $1{\frac{1}{2}}$min. 2min. and $2{\frac{1}{2}}$min. respectively in the test group. Then, specimens were processed for scanning electron microscopic observation. The results of this study were as follow. 1. Both test and control group showed a few shallow grooves and ridges in pure titanium machined surface implants. There were not significant differences between two group. 2. In GBA surfaces, control group exhibit many porous depression, and each depression were divided by strict border. Experimental group applied with tetracycline-HCl for 2min. were similar with control group. But when applied for $2{\frac{1}{2}}$min. surface alteration and border breakdown started, resulting enlargement of the porous depression. 3. In REM surface, control group exhibit rough, uneven surface with crater-like depression can be found. The surface alteration started when tetracycline-HCl was applied for 30sec. resulting breakdown of the crater-like depression. Depression became larger as applying time increased.

• Journal of Conservation Science
• /
• v.30 no.4
• /
• pp.395-407
• /
• 2014

In this study, firing temperature of bricks from the Songsanri tomb complex is interpreted based on the mineralogical and physical changes of soil samples fired at different temperature. When soil samples were burned at 500 to $1,200^{\circ}C$, phase transition of clay minerals affected the mineralogical composition and microstructure, which leaded to alteration of physical features as color, water absorption and porosity. Mineralogical composition can be assumed to vary with the temperature by mineral phase stability, however, color, water absorption, porosity and microstructure had slow change under $1,000^{\circ}C$, and had rapid change from 1,000 to $1,200^{\circ}C$. Upon the mineral and physical alteration of soil, firing temperature of bricks from the Songsanri tomb complex were estimated. Some bricks were over fired at temperature more than $1,200^{\circ}C$, some high-burned bricks were fired from 1,100 to $1,200^{\circ}C$, some bricks were fired by 900 to $1,000^{\circ}C$ and some bricks ere assumed not to be fired. Henceforward mineralogical and physical study can be applied to interpretate more precise firing temperature.

• Journal of Periodontal and Implant Science
• /
• v.40 no.6
• /
• pp.276-282
• /
• 2010

Purpose: The present study was performed to evaluate the effect of erbium:yttrium-aluminium-garnet (Er:YAG) laser irradiation on the change of hydroxyapatite (HA)-coated implant surface microstructure according to the laser energy and the application time. Methods: The implant surface was irradiated by Er:YAG laser under combination condition using the laser energy of 100 mJ/pulse, 140 mJ/pulse and 180 mJ/pulse and application time of 1 minute, 1.5 minutes and 2 minutes. The specimens were examined by surface roughness evaluation and scanning electron microscopic observation. Results: In scanning electron microscope, HA-coated implant surface was not altered by Er:YAG laser irradiation under experimental condition on 100 mJ/pulse, 1 minute. Local areas with surface melting and cracks were founded on 100 mJ/pulse, 1.5 minutes and 2 minutes. One hundred forty mJ/pulse and 180 mJ/pulse group had surface melting and peeling area of HA particles, which condition was more severe depending on the increase of application time. Under all experimental condition, the difference of surface roughness value on implant surface was not statistically significant. Conclusions: Er:YAG laser on HA-coated implant surface is recommended to be irradiated below 100 mJ/pulse, 1 minute for detoxification of implant surface without surface alteration.

• Journal of Periodontal and Implant Science
• /
• v.41 no.3
• /
• pp.135-142
• /
• 2011

Purpose: The present study was performed to evaluate the effect of erbium-doped: yttrium, aluminium and garnet (Er:YAG) laser irradiation on sand-blasted, large grit, acid-etched (SLA) implant surface microstructure according to varying energy levels and application times of the laser. Methods: The implant surface was irradiated by the Er:YAG laser under combined conditions of 100, 140, or 180 mJ/pulse and an application time of 1 minute, 1.5 minutes, or 2 minutes. Scanning electron microscopy (SEM) was used to examine the surface roughness of the specimens. Results: All experimental conditions of Er:YAG laser irradiation, except the power setting of 100 mJ/pulse for 1 minute and 1.5 minutes, led to an alteration in the implant surface. SEM evaluation showed a decrease in the surface roughness of the implants. However, the difference was not statistically Significant. Alterations of implant surfaces included meltdown and flattening. More extensive alterations were present with increasing laser energy and application time. Conclusions: To ensure no damage to their surfaces, it is recommended that SLA implants be irradiated with an Er:YAG laser below 100 mJ/pulse and 1.5 minutes for detoxifying the implant surfaces.

• Geomechanics and Engineering
• /
• v.23 no.2
• /
• pp.103-113
• /
• 2020

Gypsiferous soils classified as problematic soils due to the dissolution of gypsum. Presence of gypsum in the soils texture subjected to steady flow can cause serious damages for the buildings, roads and water transmission canals. Therefore, researchers have conducted a series of physical, mechanical and microstructural laboratory tests to study the effect of gypsum leaching on the geotechnical properties of a lean clay containing 0%, 3%, 6%, 9%, 12%, and 15% raw gypsum. In addition, a combination of two nano-chemical stabilizers named Terrasil and Zycobond was used in equal proportions to stabilize the gypsiferous clayey samples. The results indicated that gypsum leaching considerably changed the physical and mechanical properties of gypsiferous soils. Further, adding the combination of Terrasil and Zycobond nano-polymeric stabilizers to the gypsiferous soil led to a remarkable reduction in the settlement drop, compressibility, and electrical conductivity (EC) of the water passing through the specimens, resulting in improving the engineering properties of the soil samples. The X-ray diffraction patterns indicate that stabilization by terrasil and zycobond causes formation of new peaks such as CSH and alteration of pure soil structure by adding raw gypsum. Scanning electron microscope (SEM) images show the denser texture of the soil samples due to chemical stabilization and decrease of Si/Al ratio which indicates by Energy dispersive X-ray (EDS) interpretation, proved the enhance of shear strength in stabilized samples.