• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 한국초전도저온공학회 2000년도 KIASC Conference 2000 / 2000년도 학술대회 논문집
• /
• pp.6-8
• /
• 2000

The critical current density, Jc, of superconductor tape significantly depends on microstructural evolution during mechanical deformation. In this study, we fabricated Bi-2223 superconductor tape by PIT technique, and investigated mechanical properties of mono- and 61-filamentary tapes and their joined tapes. The strength of mono-filament tape was higher than those of 61-filament tape was higher than those of 61-filament tape, respectively. On the other hand, elongation of mono-filament tape, respectively. On the other hand, elongation of mono-filament tape was lower than 61 filament tape. The joined tapes shows lower strength and irreversible strain than those of unjoined tapes. The reduced strength and irreversible strain for joined tape is probably related to the induced damages such as irregular interface and Ag-instrusion in the transition region which acts as a stress concentration.

• Advances in materials Research
• /
• 제9권3호
• /
• pp.171-187
• /
• 2020

The microstructural evolution of different compositions of Mg-Sn alloys (30%Sn-70%Mg, 40%Sn-60%Mg and 50%Sn-50%Mg) is studied at first to understand the changes observed with change in tin content and deformation conditions. The Mg₂Sn phase increases with increase in tin content and a significant substructure development is found in 50%Sn-50%Mg alloy. The above observation led to further deformation studies on Mg₂Sn based thermoelectric materials with higher tin percentage. The microstructure in terms of Electron backscatter diffraction (EBSD)measurements is studied in detail followed by the determination of thermoelectric properties i.e., Seebeck coefficient and electrical conductivity for both as cast and extruded Mg_(2+x)Sn-Ag alloys. The electrical conductivity of the extruded Mg_(2+x)Sn-.3wt%Ag {x =1} alloy was found to be more than its as cast counterpart while the Seebeck coefficient values remained almost the same.

• 연구논문집
• /
• 통권32호
• /
• pp.77-84
• /
• 2002

A martensitic precipitation hardening stainless steel, 17-4PH has been widely used in the aircraft, chemical and nuclear industries for long time, owing to the excellent mechanical properties with corrosion resistance that can be achieved by simple heat treatment. The microstructure and mechanical properties of the 17-4PH stainless steel cast parts for aircraft, such as impeller, are largely affected by heat treatment condition. But the database of heat treatment has not been clearly established in the domestic investment casting industries because the domestic aerospace, industry lags behind the advanced countries. In this study, the microstructural evolution and mechanical properties of cast 17-4PH stainless steel depending on the heat treatment conditions and aging at $400^{\circ}C$ were investigated.

• Journal of Surface Science and Engineering
• /
• 제28권6호
• /
• pp.376-385
• /
• 1995

Copper-chromium multilayers with a nominal bilayer thickness of about 400 $\AA$ (200 $\AA$ each) were prepared by dc magnetron sputtering and the evolution of microstructure during heat treatment was investigated by using x-ray diffractometry(XRD), Auger electron spectroscopy(AES) and transmission electron microscopy(TEM). It was observed that an amorphous phase with a thickness of about 40 $\AA$ was formed at the interfaces of the as-deposited Cu/Cr multilayered film using cross-sectional TEM. At elevated temperatures, the Cu(111) reflection showed increasing intensity and decreasing line-width as a result of copper grain growth. The intermixed amorphous phase disappeared after annealing at $250^{\circ}C$ for 1 h and the multilayer structure was stable up to $400^{\circ}C$ for 1 h annealing. At $600^{\circ}C$ annealing, it was observed that the multilayer structure was completely destroyed and copper and chromium phases were fully intermixed.

• Journal of Powder Materials
• /
• 제7권1호
• /
• pp.19-26
• /
• 2000

Al-Cr-Zr metal powders were prepared by cryo-milling(-75$^{\circ}C$),ambi-milling(25$^{\circ}C$) and warm-milling(200$^{\circ}C$) to investige the effect of milling temperature. The morphogical changes and microstructural evolution of Al-6wt.%Cr-3wt.%Zr metal powder ball milling were investigated by SEM, OM and XRD. The cryo-milling at -75$^{\circ}C$ caused the more refinement of powder particle size than ambi-milling and warm-milling. The partic morpholgy of Al-Cr-Zr metal powders changed changes into spheroidal particles at 25$^{\circ}C$and spherical particles at 200$^{\circ}C$The spherical particles were formed by agglomertion and contiuous wrapping of the spheroidal particles. The calculated Al crystallite size in Al-Cr-Zr metal powders by the Scherer equation were refined rapidly for short milling time -75$^{\circ}C$compared with milling at 25$^{\circ}C$ and 200$^{\circ}C$.

• Journal of Korea Foundry Society
• /
• 제21권4호
• /
• pp.246-252
• /
• 2001

Variation in the microstructure of Mg-5%Al semi-solid slurry during isothermal heating was investigated in relation to initial microstructure, holding time, and holding temperature. Specimens with three different initial microstructures were isothermally heated. Dendritic structure in as-cast ingot was decomposed into solid globules in the semi-solid slurry during isothermal holding, while in the recrystallized specimens prepared by extrusion or rolling the size of solid particles was continuously increased during the heating. Effects of mold temperature and liquid fraction of slurry on the mold filling ability were also studied. Very thin section (0.4 mm) could be successfully filled up to 50 mm by 60% liquid slurry when the mold was heated to $600^{\circ}C$.

• Journal of Korea Foundry Society
• /
• 제28권2호
• /
• pp.69-73
• /
• 2008

In the present study, microstructural evolution and mechanical properties of Ti-Fe-Sn ultrafine eutectic alloys have been investigated. Ultrafine eutectic microstructure consisting of a mixture of ${\beta}$-Ti solid solution and TiFe intermetallic compound homogeneously formed in $(Ti_{70.5}Fe_{29.5})_{100-x}Sn_x$ alloys with x = 0, 1 and 3. Addition of Sn is effective to modify the eutectic colony into the spherical shape with decreasing the lamellar spacing and colony size. This results in enhancing the macroscopic plasticity up to 3.1% of the Ti-Fe-Sn ultrafine eutectic alloys.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 한국초전도저온공학회 2003년도 학술대회 논문집
• /
• pp.72-74
• /
• 2003

We fabricated textured Ag substrates for coated conductor and evaluated the effects of annealing temperature on microstructural evolution, texture formation, and surface morphology. A strong {110}〈110〉 textured Ag substrate was obtained by cold rolling and annealing at 80$0^{\circ}C$: the full-width at half-maximum(FWHM) value of {110}〈110〉 poles was as sharp as 10$^{\circ}$. Surface morphology was evaluated by using Atomic force microscopy(AFM). Root-mean-square(RMS) roughness of the substrate annealed at 80$0^{\circ}C$ was 39.2 nm. The substrate of strong texture and smooth surface, fabricated in our study, is considered to be suitable for use as a substrate for deposition of superconductor films.

• Journal of the Korean Ceramic Society
• /
• 제37권12호
• /
• pp.1140-1145
• /
• 2000

Ni의 함량이 서로 다른 Ni-YSZ 복합체를 100$0^{\circ}C$ 환원 분위기 하에서 열처리하며 시간에 따른 미세구조의 변화를 관찰하였다. Quantitative microscopy 이론을 응용한 화상분석 결과 Ni-YSZ 복합체의 미세구조는 열처리시 나타나는 Ni상의 미세구조 변화에 가장 큰 영향을 받고 있었다. 특히 Ni의 양이 많은 조성에서는 Ni 상간의 접촉이 많아 고상반응에 의한 미세구조의 변화가 심하였는데 이로 인해 복합체 미세구조의 안정화가 느리게 진행되었다. Ni-YSZ 복합체의 전기 전도도 역시 Ni상의 미세구조 변화에 큰 영향을 받았는데 복합체 전체 미세구조의 경시변화와는 달리 Ni상의 많은 조성보다는 Ni상의 percolation이 일어나는 조성 부근에서 더 큰 영향을 받았다. 이로 인해 Ni-YSZ의 전기 전도도는 Ni의 percolation threshold 부근 조성에서 안정화되는데 더 많은 시간을 요하였다.

• Transactions of Materials Processing
• /
• 제9권6호
• /
• pp.663-669
• /
• 2000

A material model has been presented, at the continuum level, for the representation of superplastic deformation coupled with microstructural evolution. The model presented enables the effects of the spatial variation of distributions of grain size to be predicted at the process level. The model has been tested under conditions of both homogeneous and inhomogeneous stress and strain by carrying out detailed comparison of predicted distributions of grain size and their evolutions with experimentally obtained data. Experimental measurements have shown the extent of the spatial variation of the distribution of grain size that exists in the titanium alloy, Ti-6Al-4V. It is shown that whilst not large, the variations in grain size distributions are sufficient to lead to the development of inhomogeneous deformation in test pieces, which ultimately result in localisation of strain and failure.