• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.813-819
• /
• 2011

In this paper, a new design method of a tunable oscillator using a suspended-stripline resonator is presented. The negative resistance of an FET mounted on microstrip line(MSL) is combined with a high Q suspended-stripline(SSL) resonator to produce a tunable oscillator with good phase noise. The new MSL-SSL transition facilitates the easy connection between the MSL-based circuits and the SSL module. The proposed oscillator is also frequency-tunable using a tuner located on the top of the SSL housing. The measured phase noise of the implemented oscillator at 3.37 GHz is -108.03 dBc@100 kHz and -135.09 dBc@1 MHz with 50 MHz of frequency tuning.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.11a
• /
• pp.61-64
• /
• 2000

We fabricated and characterized Low Noise Amplifier (LNA) using MCM-C (Multi-Chip-Module-Cofired) technology for 2.14 GHz IMT-2000 mobile terminal application. First, We designed LNA circuits and simulated it's high frequency characteristics using circuits simulator. For the simulation, we adopted high frequency libraries of all the devices used in LNA samples. By the simulation, Gain was 17 dB and Noise Figure was 1.4 dB. We used multilayer process of LTCC (Low Temperature Co-fired Ceramics) substrate and conductor, resistor pattern for the MCM-C LNA fabrication. We made 2 buried inductors, 2 buried capacitors and 3 buried resistors. The number of the total layers was 6. On the top layer, we patterned microstrip line and pads for the SMT device. We measured the high frequency characteristics, and the results were 14.7 dB Gain and 1.5 dB Noise Figure.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.11
• /
• pp.34-39
• /
• 2002

In this paper, we proposed novel photonic bandgap(PBG) structure using EGP(Elevated Ground Plane) and via in ceramic substrate of microstrip line. From analysis result, the proposed PBG structure is reduced 52.5% at size and increased 45 % at bandwidth compared to typical planar PBG structure. It is also reduced 32 % at size and improved more than 8 dB at power loss compared to typical multilayer DGS(Defected Ground Structure). The proposed PBG structure also can be used bandstop and lowpass filter and it will be useful for small microwave integrated circuit and module development.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.7
• /
• pp.613-619
• /
• 2015

In this paper, we proposed a paper-based pattern-switchable antenna using inkjet-printing technology. The proposed antenna is composed of two bow-tie antennas and a switching network. The bow-tie antennas are inkjet-printed on paper using a low cost home printer. The switching network is built on a printed-circuit-board(PCB) and consists of a single-pole-double-throw(SPDT) switch and balun element. A double-sided parallel-strip line(DSPSL) can convert the unbalanced microstrip mode to the balanced strip mode. Two bow-tie antennas have different radiation patterns because of the different orientation of the reflectors. It is demonstrated from EM simulation and measurement that the radiation patterns of the proposed antenna are successfully switched by the SPDT.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.279-285
• /
• 2017

In this paper, the resonator with a parallel plate capacitor is newly proposed around sub-microwave frequency band and applied to earlobe for non-invasive glucose monitoring the human biological tissue. The capacitor including the earlobe as dielectric material is connected to inductive slot in the ground plane of the microstrip line. Based on the simulation, one port resonator circuit is designed and fabricated as a prototype. Three step glucose concentration levels(0, 250, 500 mg/dL) was tested, and its reflection coefficients($S_{11}$) were measured. Owing to high Q resonator more than 100, resonant frequency shift of about 9 MHz per glucose level of 250 mg/dL has been successfully measured. This proves that the proposed sensor is applicable to a blood glucose sensor.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.495-504
• /
• 1996

In this paper, series-fed mirostrip array anteenas with coupling-slots are prposed and their operating characteristics are analyzed based on analyzed based on analytical and experimental results. An accurate analysis method for the slot-coupled feed structure is based on using both circuit coupling between anteenas and full-wave analysis which use travling wave mode and non-traveling wave mode on feed line. The basis functions that used for the numerical analysis bas been determined depending upon the accuracy, convergence properties of the solution, and the computation time:The patch uses 3 EB mode, the slot uses 1PWS mode, and feeders use 5 PWS mode. Series-fed array antennas have been designed, built, and tested in a standing-wave configuration. Using the results of the full-wave analysis, the chebyshev array antennas consisting of 8 elements are designed and fabricated changing the amount excited to each array element by adjusting slot length and by the slot position relative to the feeder. Experiment results show that the series-fed array antenna designed by adjusting the slot position relative to the feeder is superior to that designed by slot length.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1292-1299
• /
• 2003

In this paper, we fabricated new GaAs-based dielectric-supported air gapped microstriplines(DAMLs) using the surface MEMS and the LPF for Ka-band using the fabricated DAMLs. We elevated the signal lines from the substrate, in order to reduce the substrate dielectric loss and obtain low losses at millimeter-wave frequency band with wide impedance range. We fabricated LPF with DAMLs for Ka-band. Due to reducing the dielectric loss of DAMLs, the insertion loss of LPF can be reduced. Miniature is essential to integrate LPF with active devices, so that we fabricated LPF with the slot on the ground to reduce the size of the LPF. We compared a characteristic to LPF with the slot and LPF without the slot.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.2
• /
• pp.171-178
• /
• 1998

Generally, the output matching circuit has the most influence to the output power of oscillator and existing method for output matching has difficulty for making the optimum output matching circuit because the matching has to be done nearby the infinite impedance area of the Smith Chart. In this paper, it is studied for the output matching circuit of the microwave oscillator to get the maximum output power. The maximum output point can be found by adjusting the position of moving short in the Tuner while the oscillator is operating after connect the 3-dB coupler Tuner to the oscillator without output matching circuit. To design the oscillator for the maximum output power can be done easily with the microstrip line which is realized from the measured S-parameters of Tuner. In compare the oscillator by the existing method with another one by the suggested method in this paper, the first one has 6.45 dBm output power and second one has 9.71 dBm which is 3.26 dBm higher than the first one at the oscillation frequency 1.0338 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.12
• /
• pp.1402-1407
• /
• 2007

This paper presents a new design method of the Ultra-Wide-Band BandPass Filter using the CRLH-TL(Composite Right- and Left-Handed Transmission-line) having the Metamaterials' properties. Instead of the periodic type or many cells of the CRLH-TL, only the unit cell is used to miniaturize the target component, which can not be realized by the conventional quarter guided-wavelength resonator-based filters. Particularly, the strong coupling essential to the Ultra Wide Band is enabled by the interdigital coupled lines between the grounded stubs. The proposed design scheme is validated by the electromagnetic simulation and measurement of the fabricated filter which shows the total size of 'the guided-wavelength/9.4', the 100 % fractional bandwidth for the UWB, the insertion loss of less than 1 dB and the flat group-delay.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.241-247
• /
• 2007

This paper introduces a new type push-push harmonic dielectric resonator oscillator. Proposed oscillators are utilized by HDRO(Harmonic Dielectric Resonator Oscillator) which are combined in push-push structure. As a result, fundamental signal suppression ratio and output power of harmonic signal has been improved. The increase of phase noise is compensated by improving coupling characteristic between resonator and parallel microstrip line. The proposed push-push HDRO shows the output power of 9.32 dBm, the fundamental signal suppression of -47.2 dBc and phase noise of -99.86 dBc at 100 kHz offset frequency and 18.7 GHz center frequency.