• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.792-796
• /
• 2003

In this paper, to detect external sound frequency on the latticed structure, fiber optic sensor net using Sagnac interferometer was fabricated and tested. The latticed structure fabricated with dimension of 50cm in width and 50cm in height, the optical fiber, 50m in length, distributed and fixed on the latticed structure. Single mode fiber, a laser with 1,550nm in wavelength, 2${\times}$2 coupler were used. External sound signal applied to the fiber optic sensor net and the detected optical signals were compared and analyzed to the detected microphone signals against time and frequency domain. Based on the experimental results, fiber optic sensor net using Sagnac interferometer detected external sound frequency, effectively. This system can be expanded to the structural health monitoring system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.539-544
• /
• 1997

Although the identification of a moving noise source is important in reducing the source power of the transport systems such as airplane or high speed train, the direct measurement of the frequency characteristics is usually difficult due to wind noise when using a microphone running with that noise source. On the other hand the motion of a source causes the frequency characteristics of the pass-by sound measured at a fixed point to be distorted that it is quite difficult to identify the original source characteristics. In this study the relationship between the spectra of the source and the pass-by sound signal is analyzed for a source moving at a constant velocity. The effects of the speed and the frequency characteristics of the source on the pass-by noise spectrum are investigated through numerical simulations.

• Journal of KSNVE
• /
• v.2 no.2
• /
• pp.107-116
• /
• 1992

An adaptive signal processing technique is implemented for the active noise cancellation of the plane acoustic wave propagating in a duct. To avoid the instability caused by the acoustic feedback from the control speaker to the detect microphone, an off-line modeling of the acoustic feedback plant is done using the FIR filter. Auxiliary path required for the filtered-x LMS algorithm is modeled as well. Before going into the experiments, a simulation is carried out under the same conditions with experiments. The simulation shows that the longer the length of the adaptive filter is, the better the results are achieved. Experiments have been carried out at lower audio frequency range (50 - 400Hz), and the results are in good agreements with those of simulation study. As a results of this adaptive noise control, around 50dB is reduced for a pure tone noise, and for a bandlimited noise with the bandwidth of 316Hz, a maximum of 30dB noise reduction is attained.

• Phonetics and Speech Sciences
• /
• v.1 no.3
• /
• pp.95-102
• /
• 2009

In this paper, an efficient target speech detection algorithm is proposed for the performance improvement of multi-input speech enhancement. Using the normalized cross correlation value between two selected channels, the proposed algorithm estimates the probabilistic distribution function of the value from the pure noise interval. Then, log-likelihoods are calculated with the function and the normalized cross correlation value to detect the target speech interval precisely. The detection results are applied to the generalized sidelobe canceller-based algorithm. Experimental results show that the proposed algorithm significantly improves the speech recognition performance and the signal-to-noise ratios.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.11
• /
• pp.583-588
• /
• 2004

We stabilized the frequency and power of a high voltage excited CW CO2 laser on the peak of the Doppler broadened gain curve using the photoacoustic effect generated from the laser itself. The photoacoustic signal is directly coupled from an radio frequency discharge chamber via a capacitor microphone into a detector and a lock-in stabilizer. The frequency stability is estimated to be better then 1.2×10/sup -7/ at the transition P(20) line. The stabilized output power variation was reduced to from 77 % to 3.3 %.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.10
• /
• pp.947-954
• /
• 2012

Sand scorpions are nocturnal animals to mostly use tactile senses to detect their prey. It has been reported that sand scorpions have high vibration sensitivity for their prey-localizing behavior. We tested vibration experiments in the sand with microphone sensors to model the sand scorpion's behavior and a time-difference model was applied to find the direction of a vibration source. Using the information of the arrival time of the vibration signal to reach each leg position, we can find the location of the vibration source.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2259-2261
• /
• 1998

Auditory Models that are capable of achieving human performance would provide a basis for realizing effective speech processing systems. Perceptual invariance to adverse signal conditions (noise, microphone and channel distortions, room reverberations) may provide a basis for robust speech recognition and speech coder with high efficiency. Auditory model that simulates the part of auditory periphery up through the auditory nerve level and new distance measure that is defined as angle between vectors are described.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.641-645
• /
• 2001

In this paper, it is discussed that active noise control in a circular duct using smart foam. Firstly, it is demonstrated that the potential of the conventional smart foam, proposed by Fuller, for active noise control in a duct. Conventional smart foam is not applicable to active noise control in a duct having flow. Thus, this paper presents a ring-type smart foam as an alternative. The ring-type smart foam consists of polyurethane acoustic foam of lining shape and PVDF film embedded in the foam. The embedded PVDF element acts as an actuator to reduce noise at lower frequencies and the foam absorbs noise at higher frequencies. A filtered-x LMS controller is used to minimize the signal from the error microphone. Experiments are executed to reduce broadband and tonal noise.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.685-688
• /
• 2000

In this paper, we used image information for the enhancement of Korean numeral speech recognition. First, a noisy environment was made by Gaussian generator at each 10 dB level and the generated signal was added to original Korean numeral speech. And then, the speech was analyzed to recognize Korean numeral speech. Speech through microphone was pre-emphasized with 0.95, Hamming window, autocorrelation and LPC analysis was used. Second, the image obtained by camera, was converted to gray level, autocorrelated, and analyzed using LPC algorithm, to which was applied in speech analysis, Finally, the Korean numerial speech recognition with image information was more ehnanced than speech-only, especially in ‘3’, ‘5’and ‘9’. As the same LPC algorithm and simple image management was used, additional computation a1gorithm like a filtering was not used, a total speech recognition algorithm was made simple.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.209-212
• /
• 2002

The wear process of end mill is a so complicated process that a more reliable technique is required for the monitoring and controling the tool life and its performance. This research presents a new tool wear monitoring method based on the sound signal generated on the machining. The experiment carried out continuous-side-milling for 4 cases using the high-speed steel slot drill under wet condition. The sound pressure was measured at 0.5m from the cutting zone by a dynamic microphone, and was analyzed at frequency domain. The tooth passing frequency appears as a harmonics form, and end mill wear is related with the first harmonic. It can be concluded from the result that the tool wear is correlate with the intensity of the measured sound at tooth passing frequency estimation of end mill wear using sound is possible through frequency analysis at tooth passing frequency under the given circumstances.