• 한국분무공학회지
• /
• 제21권1호
• /
• pp.58-63
• /
• 2016

This study presents the dynamic characteristics of an impinging droplet on hydrophobic and hydrophilic surfaces with various texture area fractions. The flat surface was fabricated by using the drilling technique to make micro-meter hole-patterned surfaces, which shows hydrophobic textured surfaces. Moreover, the hydrophilic textured surfaces were manufactured by anodizing technique on the micro-meter hole-patterned surfaces to generate multi-layer surfaces. Impinging droplet experiments were conducted for various hole-patterned surfaces, with changing impact velocity and texture area fractions. It is observed that an anodizing technique increases wettability by decrease in hole diameter on the textured surfaces. However, micro-drilled surfaces decreases wettability because the hole diameter was so large that air can be trapped under the holes. In addition, the maximum spreading diameter decreases with the texture area fraction for the micro-drilled surfaces because of decrease in wettability.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.247-248
• /
• 2009

• Current Applied Physics
• /
• 제18권11호
• /
• pp.1368-1374
• /
• 2018

In this paper, forced vibration was used to regulate the droplet migration, fully recording the transient migration of droplets on a micro-textured substrate under the resonance frequency by a high-speed camera. The influence of resonance frequency and dynamic migration characteristics of droplets on the solid micro-texture surface under lateral vibration were researched. The experiment demonstrates that the driving force is caused by the difference between the left and right contact angles made the droplet oscillate and migrate, and as time t increases, the left and right contact points are periodically shifted and the amplitude of migration increases. Therefore, based on the droplet migration behavior and its force balance mechanism, a spring vibration model of migration behavior of the vibrating droplet micro unit was set up to predict the complete trajectory of its migration on a solid surface. The calculation results show that the theoretical displacement is less than the experimental displacement, and the longer the time, the larger the difference. Affected by the vibration, part of the droplet permeates through the micro-texture, resulting in the droplet losing height and the contact angle becoming smaller as well. While the other part of droplet overcomes the internal surface tension to migrate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.217-222
• /
• 2004

The aim of this paper is to investigate the effect of micro-dimple size on reduction friction and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.320-320
• /
• 2012

III-V 화합물 태양전지는 실리콘, CdTe, CIGS, 염료, 및 유기 등 다른 태양전지에 비해 1sun 상 30% 이상의 고효율을 갖고 있고 앞으로도 계속 증가할 수 있는 가능성을 갖고 있다. 그 이유는 직접천이형 밴드갭, 높은 이동도 등의 고성능 물질특성과 더불어 3족과 5족의 비율을 조절함으로써 같은 결정구조를 갖고 에너지 밴드갭이 다른 물질들을 만들기에 용의하여, 태양전지 스펙트럼의 넓은 영역을 흡수할 수 있는 장점이 있기 때문이다. 그러나, 셀자체의 물질이 실리콘에 비하여 고가이므로, 고성능이 요구되는 우주 인공위성등에 적용이 되었지만, 2000년대 이후로 집광에 적용가능한 태양전지의 연구를 거듭하여 2005년부터는 값싼 프레넬 렌즈를 이용하여 1sun에 비해 500배 해당하는 빛을 셀에 집광하여 보다 효율을 증가시킴으로써 지상발전용에도 적용가능한 셀을 형성하게 되었다. 더불어 태양전지의 효율을 증가시키기 위한 개선된 구조적 변화의 시도도 많이 이루어지고 있다. 최근 보고에 의하면 실리콘 태양전지의 표면에 texture 또는 나노 구조를 주어 높은 흡수율과 낮은 반사율을 갖게 함으로써 효율을 증가시키는 사례가 많아지고, III-V 화합물 태양전지도 texturing에 의해 증가된 효율을 발표한바 있다. 본 연구에서는 태양전지의 효율을 증가시키기 위하여 III-V 화합물 태양전지 표면에 micro-hole array texture 구조를 형성한 후 나노 particle을 이용한 나노 texture 구조를 형성하였다. Photo-lithography와 chemical wet etching으로 micro-hole array texture 구조를 형성하였으며 micro-hole의 직경은 $5{\sim}20{\mu}m$, hole과 hole의 간격은 $3{\sim}15{\mu}m$로 다양하게 변화를 주었다. 형성된 micro-hole array texture 구조위에 수십 nm 크기의 particle을 만들어 chemical wet etching으로 나노 texture 구조를 형성하였다. 태양전지 표면에 texture 구조가 있는 경우와 없는 경우에 각각 효율을 측정, 비교 분석하였다.

• Tribology and Lubricants
• /
• 제20권5호
• /
• pp.266-271
• /
• 2004

The aim of this paper is to investigate the effect of surface texturing on reduction friction and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.437-438
• /
• 2008

• 소성∙가공
• /
• 제29권2호
• /
• pp.113-117
• /
• 2020

Various parameters are involved in the frictional behavior of steel sheet during stamping. We performed various tests in order to investigate the influence of tool surface texture directionality upon the resulting friction in sheet forming processes. Four different tools were manufactured which gave us a range of roughness for both parallel and transverse texture directions. Each of the tools was examined in flat type friction tests under identical test conditions. The tool with the transverse surface texture produces significantly lower levels of friction than the tool with parallel texture direction. Considering the lubrication mechanism associated with transverse texture, one can imagine the lubricant being constantly supplied from the reservoir of the micro valley to the point of contact and hence producing the lower levels of friction seen.

• 한국기계가공학회지
• /
• 제5권4호
• /
• pp.21-26
• /
• 2006

Characteristics of texture and groove precision lapping plate are experimentally investigated by Measuring frictional forces. It is found that the frictional coefficient decreases as the embedding of diamond particles progresses. The groove precision lapping plate with concentric micro-channels indicates superior capability in embedding micrometer-sized diamond particles and uniformity in diamond embedding compared with the texture precision lapping plate with a series of circular micro-channels.

• 한국기계가공학회지
• /
• 제8권1호
• /
• pp.31-36
• /
• 2009

Micro-machining technology has been adopted for shape accuracy of micrometer and sub-micrometer scale, surface roughness of tens nanometer in industries. In micro-machining process the quality of machined surface is derived from machining condition and tooling. This paper investigates AE(acoustic emission) and cutting force signals according to machined surface quality related to machining condition. Machined surface quality was analyzed by the AE and cutting force parameter which reflect surface morphology. The characteristics of signal were extracted for process optimization by monitoring both the tool condition and the machined surface texture in micro end milling process.