• 조명전기설비학회논문지
• /
• 제24권9호
• /
• pp.1-7
• /
• 2010

Ceramic metal halide lamps have been widely used due to long lifetime, high luminous efficiency and good colour rendering. 35[W] ceramic metal halide lamps has very different characteristics between ignition state and steady state. The developed electronic ballast is satisfied to both ignition state and steady state characteristics by using a micro-controller. The proposed electronic ballast is consists of EMI filter, Full-wave rectifier, Active PFC, DBI(Dual Buck Inverter), Igniter and control circuit. It enables to supply both low-frequency rectangular wave voltage and current to the lamp by using DBI(Dual Bcuk Inverter) structure.

• Journal of Power Electronics
• /
• 제13권6호
• /
• pp.919-927
• /
• 2013

This paper proposes a Boundary Current Mode (BCM) control scheme to realize soft switching on a conventional single phase full bridge DC/AC inverter. This technique with the advantages of no auxiliary components, low cost, high efficiency, and simple in control, is attractive for micro-inverter applications. The operation principle and characteristic waveforms of the proposed soft switching technique are analyzed in theory. A digital controller is provided based on that theory. To balance the requirements of efficiency, switching frequency, and inductor size, the design considerations are discussed in detail to guide in BCM inverter construction. A 150W prototype is built under these guidelines to implement the BCM control scheme. Simulation and experiment results demonstrate the feasibilities of the proposed soft switching technique.

• Journal of Power Electronics
• /
• 제19권6호
• /
• pp.1403-1412
• /
• 2019

A coupled inductor-dual boost-inverter (CIDBI) with a differential structure has been presented for application to a micro-inverter photovoltaic module system due to its turn ratio of a high-voltage level. However, it is difficult to design a CIDBI converter with a conventional PI regulator to be stable and achieve good dynamic performance, given the fact that it is a high order system. In view of this situation, a sliding mode control (SMC) strategy is introduced in this paper, and two different sliding mode controllers (SMCs) are proposed and adopted in the left and right side of two Boost sub-circuits to implement the corresponding regulation of the voltage and current. The schemes of the SMCs have been elaborated in this paper including the establishment of a system variable structure model, selection of the sliding surface, determination of the control law, and presentation of the reaching conditions and sliding domain. Finally, the mathematic analysis and the proposed SMC are verified by experimental results.

• 한국멀티미디어학회논문지
• /
• 제18권7호
• /
• pp.864-872
• /
• 2015

The purpose of this study is to design the algorithm, Predictive Service Component - PSC, for forecasting and judging obsolescence of solar system that is implemented based on the micro-inverter. PSC proposed in this study is suitable for monitoring of distributed power generation systems. It provides a diagnosis functionality to detect failures and anomaly events. It also can determine the aging of PV systems. The conclusion of this study shows the research and development of this kind of integrated system using PSC will be needed more and varied in the near future.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.414-420
• /
• 2005

The ShortStack Micro Server enables any product that contains a microcontroller or microprocessor to quickly and inexpensively become a networked, Internet-accessible device. The ShortStack Micro Server provides a simple way to add LonWorks networking to new or existing smart devices. . It implements the LonTalk protocol and provides the physical interface with the LonWorks communication. The ShortStack host processor can be an 8, 16, or 32-bit microprocessor or microcontrollers. The ShortStack API and driver typically require about 4kbytes of program memory on the host processor and less than 200 bytes of RAM. The interface between host processor and the ShortStack Micro Server may be a Serial Communication Interface (SCI). The LonWorks control module with a high performance is developed, which is composed of the 8 bit PIC Microprocessor for host processor and the smart neuron chip for the ShortStack Micro Server. This intelligent control board is verified as proceeding the various function tests from experimental system with an boost pump and inverter driving systems. It is also confirmed that the developed control module provides stably 0-10VDC linear signal to the input signal of inverter driving system for varying the induction motor speed. Thus, the experimental results show that the fabricating intelligent board carried out very well the various functions in the wide operating ranges of boost pump system. This developed control module expect to apply to industrial fields to require the comparatively exact control and monitoring such as multi-motor driving system with inverter, variable air volume system and the boost pump water supply systems.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.1067-1068
• /
• 2008

An inverter for driving flat fluorescent lamp(FFL) with various protection circuits using micro controller(Micom) is proposed in this paper. The inverter will be shut down if the fault operating conditions such as open lamp, over current and over voltage are detected.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권2호
• /
• pp.288-294
• /
• 2011

본 논문에서는 FPGA기반의 SoC보드(Xilinx Virtex-4 ML401 EVM)를 이용한 전력인버터제어시스템을 설계하였다. 선박에 전력시스템을 적용하기 위해서 선박의 최신 통신 프로토콜인 NMEA 2000 표준 프로토콜을 적용하였으며 전력 시스템의 성능을 평가하기 위한 PC기반의 모니터링 프로그램을 제작하였다. 전력 제어시스템은 FPGA기반의 임베디드 SoC보드상에서 이중프로세서(Dualprocessor)형태로 설계하였으며 이중프로세서를 적용함으로써 실시간 제어 감시가 가능하다. 이중프로세서 중 하나는 전력 제어를 위한 PWM신호생성 및 전력 회로내의 주요 전력 파라미터를 센싱 하는 제어용 프로세서로 동작하며(Control processor) 다른 프로세서는 제어프로세서의 각종 전력 센서 파라미터와 제어 파라미터들을 이중포트 램(Dual Port RAM)을 이용하여 정보를 공유하고 외부 NMEA 2000프로토콜 기반의 모니터링 장치와 네트워크 기반의 통신을 수행하는 통신용 프로세서(Communication processor)로 구성된다. 본 논문에서 제작한 전력 제어시스템은 선박내의 분산발전,송배전 및 전압 레귤레이션 시스템에 적용 될 수 있다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 B
• /
• pp.585-587
• /
• 1998

It is suggested that the PWM inverter is controlled by Digital Software Programming. VVVF(Variable Voltage Variable Frequency) inverter control being used by PWM control for driving the motor with speed-varying, makes the PWM pattern with calculating the output voltage and frequency, and with controlling the carrier and signal, so actually this method is difficult to correspond with driving the motor by using voltage-varying and frequency-varying. Therefore this research suggested the new algorithm controlled by micro processor which is already stored by various PWM form of output voltage by using fundamental data of the carrier and signal. The PWM wave can be controlled with real time by using extra hardware and digital software and to speed up program processing, the control signals to switch the power semi-conductor of three phase PWM inverter, simultaneously use the output signal by microprocessor and extra hardware, and control signal by software. In the end, this method was proved by applying to Three Phase Voltage-type Inverter.

• 전기학회논문지
• /
• 제56권3호
• /
• pp.457-464
• /
• 2007

Micro-Grid comprising Micro-Sources supplying several $kW{\sim}MW$ power to local customers is environmentally friendly and reliable. This paper deals with the development of simulation models of Micro-Grid on the PSCAD/EMTDC platform for analyzing various aspects of the interaction of the Micro-Grid. The developed switching level model adopts the space vector PWM. Both switching level and power frequency Micro-Source models are developed, which shows that power frequency modeling is sufficient for analyzing the phenomena of interest. Control characteristics of the Micro-Sources with the parameter and load power variation are analyzed for power quality enhancement. The simulation results show that the developed models are effective for studying Micro-Grid.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1277-1280
• /
• 2005

A high-aspect-ratio and high-resolution stainless steel shadow mask for organic thin-film transistors (OTFTs) circuit has been fabricated by a new method which combines photochemical machining, micro-electrical discharge machining (micro-EDM), and electrochemical etching (ECE). First, connection lines and source-drain holes are roughly machined by photochemical etching, and then the part of source and drain holes is finished by the combination of micro-EDM and ECE processes. Using this method a $100\;\mu{m}$ thick stainless steel (AISI 304) shadow mask for inverter can be fabricated with the channel length of $30\;\mu{m}\;and\;10\;\mu{m}\;respectively.\;The\;width\;of\;connection line\;is\;150\;\mu{m}$. The aspect ratio of the wall is about 5 and 15, respectively. Metal lines and source-drain electrodes of OTFTs were successfully deposited through the fabricated shadow mask.