• 비파괴검사학회지
• /
• 제25권4호
• /
• pp.239-246
• /
• 2005

골다공증에 따른 쥐 대퇴골의 고유진동수의 변화를 예측하기 위하여 유한요소해석과 진동 시험을 수행하였다. 연구 대상으로 골다공증에 걸린 쥐 그룹, 골다공증을 치료한 쥐 그룹, 그리고 골다공증이 없는 정상 쥐 그룹을 구성하였다. 유한요소해석에서는 미세단층촬영(Micro-CT)에서 얻은 해면골 영상 데이터와 Voxel 요소 생성 알고리즘을 이용하여 3차원 미세 유한요소 모델을 생성한 다음 고유진동수 해석을 수행하였다. 진동 시험에서는 모빌리티 실험에 의한 주파수 응답함수로부터 고유진동수를 측정하였다 연구 결과로부터 골다공증에 걸린 쥐 그룹의 고유진동수가 가장 높고, 골다공증을 치료한 쥐의 그룹, 골다공증이 없는 정상 쥐의 그룹 순서로 낮아지는 경향을 볼 수 있었다. 모든 그룹에서 유한요소해석에 의한 고유진동수는 시험에서 측정한 결과보다 10-15% 오차 범위 내로 높은 값을 보였다. 본 연구로부터 개발된 미세단층촬영기 장치, Voxel 요소 생성 알고리즘, 진동시험 및 유한요소해석 방법을 이용하여 골다공증에 의한 생체 골조직의 구조적 변화 진단 및 치료 평가 등에 대한 응용가능성을 확인할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.172-176
• /
• 2002

This paper describes a MEMS-based micro-fluxgate magnetic sensing element using Ni$\_$0.8/Fe$\_$0.2/ film formed by electroplating. The micro-fluxgate magnetic sensor composed of a thin film magnetic core and micro-structured solenoids for the pick-up and the excitation coils, is developed by using MEMS technologies in order to take advantage of low-cost, small size and lower power consumption in the fabrication. A copper with 20um width and 3um thickness is electroplated on Cr(300${\AA}$)/Au(1500${\AA}$) films for the pick-up(42turn) and the excitation(24turn) coils. In order to improve the sensitivity of the sensing element, we designed the magnetic core into a rectangular-ring shape to reduce the magnetic flux leakage. An electroplated permalloy film with the thickness of 3 $\mu\textrm{m}$ is obtained under 2000Gauss to induce magnetic anisotropy. The magnetic core has the high DC effective permeability of ∼1,100 and coercive field of -0.1Oe. The fabricated sensing element using rectangular-ring shaped magnetic film has the sensitivity of about 150V/T at the excitation frequency of 2MHz and the excitation voltage of 4.4Vp-p. The power consumption is estimated to be 50mW.

• 한국전기전자재료학회논문지
• /
• 제16권2호
• /
• pp.120-124
• /
• 2003

This paper describes a MEMS-based micro-fluxgate magnetic sensing element using Ni$\_$0.8/Fe$\_$0.2/ film formed by electroplating. The micro-fluxgate magnetic sensor composed of a thin film magnetic core and micro-structure solenoids for the pick-up and the excitation coils, is developed by using MEMS technologies in order to take advantage of low-cost, small size and lower power consumption in the fabrication. A copper with 20${\mu}$m width and 3${\mu}$m thickness is electroplated on Cr (300${\AA}$) / Au (1500${\AA}$) films for the pick-up (42turn) and the excitation (24turn) coils. In order to improve the sensitivity of the sensing element, we designed the magnetic core into a rectangular-ring shape to reduce the magnetic flux leakage. An electroplated permalloy film with the thickness of 3${\mu}$m is obtained under 2000 gauss to induce magnetic anisotropy. The magnetic core has the high DC effective permeability of ~1,100 and coercive field of ~0.1 Oe. The fabricated sensing element using rectangular-ring shaped magnetic film has the sensitivity of about 150 V/T at the excitation frequency of 2 MHz and the excitation voltage of 4.4 V$\_$p p/. The power consumption is estimated to be 50mW.

• 대한기계학회논문집A
• /
• 제29권5호
• /
• pp.707-715
• /
• 2005

In this work, Scalar Passive code in Lattice Boltzmann Method is employed to simulate two-phase flow of low Reynolds number in a micro-channel. The mixing characteristics in a micro-channel is a function of Peclet number. The mixing length increases with the Peclet number. It is found that with the inclusion of static elements at the channel, rapid mixing of two liquids can be achieved, as shown by the results of computer simulations. The enhancement in mixing performance is thought to be caused by the generation of eddies and by lateral velocity component when the mixture flows past static elements. The results indicate that the size of static element has more effect on the mixing than the number of static element.

• 소성∙가공
• /
• 제22권1호
• /
• pp.36-41
• /
• 2013

The present study examines the micro-pattern replication on a plastic film using ultrasonic imprinting. Ultrasonic imprinting uses ultrasonic waves to generate repetitive microscale deformation in the polymer film. The resulting deformation heat on the surface of the film causes the surface region to soften sufficiently so that a replication of the micro-pattern can be obtained. To successfully replicate the micro-pattern on a large area of polymer film, a high replication ratio is needed as well as good uniformity over the entire region. In this study, a horn design is investigated by finite element analysis and is optimized through a response surface analysis. In the ultrasonic imprinting experiments, the response surface method was also used to determine the optimal processing conditions for better replication characteristics.

• Structural Engineering and Mechanics
• /
• 제18권5호
• /
• pp.691-707
• /
• 2004

This paper presents the micro-mechanical modeling for predicting concrete behavior under compressive loading. The model is able to represent the heterogeneities in the microstructure up to three phases, i.e., aggregate particles, matrix and interfaces. The smeared crack concept based on non-linear fracture mechanics is implemented in order to formulate the constitutive relation for each component. The splitting tensile strength is considered as a fracture criterion for cracking in micro-level. The finite element method is employed to simulate the model based on plane stress condition by using quadratic triangular elements. The validation of the model is verified by comparing with the experimental results. The influence of tensile strength from both aggregate and matrix phases on the concrete compressive strength is demonstrated. In addition, a guideline on selecting appropriate tensile strength for each phase to obtain specified concrete compressive strength is also presented.

• 소성∙가공
• /
• 제21권2호
• /
• pp.119-125
• /
• 2012

The present study addresses a direct patterning process on a plastic film using ultrasonic vibration energy. In this process, a tool horn containing micro-patterns is attached to an ultrasonic power supply, and is used with ultrasonic vibration to replicate micro-patterns on the surface of a plastic film. To improve the replication characteristics of the micro-patterns, the effect of the die shape of the ultrasonic patterning process was investigated with respect to the flow direction control. Finite element analyses were performed to predict the flow characteristics of the polymer with variations in die design parameters. Experiments were conducted using the optimally-designed die, from which it was possible to attain much improved pattern replication.

• 소성∙가공
• /
• 제11권7호
• /
• pp.581-588
• /
• 2002

Among the processes to produce micro lens, the process using press molding is a new technology to simplify the process, but it contains many unknown variables. The press-molding process proposed in this paper was simplified into two step process, the first step is the pressing to design the preform for glass element, the second step is the annealing to reduce the residual stress. It is important to estimate the amount of shrinkage of glass gob and the residual stress during process. It Is difficult to evaluate the process variables as mentioned above through the experiment. The influences due to process variables was evaluated by using FEM parametric analysis. The results in this paper can be applicable to produce micro lens.

• Journal of the Optical Society of Korea
• /
• 제13권1호
• /
• pp.75-79
• /
• 2009

A four beam interference optical system for laser micro structuring using a pulse laser was demonstrated. The four beam interference optical system using a pulse laser(picosecond laser) can fabricate micro structure on mold material(NAK80) directly. Micro structure on the polymer can be reproduced economically by injection molding of the micro structure on the mold material. The four beam interference optical system was composed by the DOE(Diffractive Optical Element) and two lenses. The laser intensity distribution of four beam interference was explained by an interference optics point of view and by the image optics point of view. We revealed that both views showed the same result. The laser power distribution of a $1{\mu}m$ peak pattern was made by the four beam interference optical system and measured by the objective lens and CCD. A $1{\mu}m$ pitch dot pattern on the mold material was fabricated and measured by SEM(Scanning Electron Microscopy).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.160.1-160.1
• /
• 2005