• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.233-239
• /
• 2013

In this paper, a method of combining numerical analyses and experimental tests is used to evaluate fracture toughness of copper thin films of $15{\mu}m$ thickness. Far-field loadings of a global-local finite element model are inversely estimated by matching crack opening profiles in experiments with numerical results. The fracture toughness is then evaluated using the J-integral for cracks in thin films under far-field loadings. In experiments, Cu thin films attached to Aluminum sheets are loaded indirectly, and crack opening profiles are observed by microscope camera. Stress versus strain curves of Cu thin films are obtained through micro-tensile tests, and the grain size of Cu thin films is observed by TEM analysis. The results show that the fracture toughness of Cu thin films with $500nm{\sim}1{\mu}m$ sized grains is $6,962J/m^2$.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.28 no.1
• /
• pp.49-59
• /
• 1995

Nine species of edible seaweed [green laver (Monostroma nitidium) and sea staghorn ( Codium fragile) of green algae; sea mustard (Undaria pinnatifida), seaweed fusiforme(Hizikia fusiforme), gulf weed (Sargassum fulvellium), and sea tangle (Laminaria japonica) of brown algae; seaweed dilatata (Halimeniopsis dilatata), seaweed furcata (Gloiopeltis furcata), and laver (Porphyra tenera) of red algae] collected from Kijang, Chungmu, and Yosu in Korea, were examined and compared on their chemical and mineral composition depending on their harvesting season. Crude protein $(N\pm6.25)$ showed about $45\%$ on moisture free basis (the contents of every components described below are shown as moisture free basis) for laver and $30\%$ for green laver collected from ever seasons and sites. Sea tangle showed the highest content in crude lipid $(10\%)$ among brown seaweeds and green laver had $6\%$ of crude lipid regardless their habitats. Ash and carbohydrate in sea staghorn hold about $90\%$ of total solids but those levels were only $50\%$ in laver. The relationship between ash and carbohydrate content showed a tendency with reverse correlation. Mineral compositions were examined on green laver, sea mustard, and seaweed furcata collected from Kijang. Sodium was eminent element (1,798-7,334mg/l00g) followed by potassium. Magnesium and calcium content were low level compared with sodium and potassium. As a micro-element iron was appraised the highest status (165-330mg/100g) in green laver, however, iron in sea mustard and seaweed furcata was comparatively low amount (2.7-47.4mg/100g). The level of zinc was also comparatively high and that was varied on habitats. In conclusion, chemical compositions of these algae were distinctively varied on species and habitats, and mineral compositions were notably changed by the harvesting season.

• Korea-Australia Rheology Journal
• /
• v.21 no.1
• /
• pp.59-69
• /
• 2009

The prediction of pressure drop for a droplet flow in a confined micro channel is presented using FE-FTM (Finite Element - Front Tracking Method). A single droplet is passing through 5:1:5 contraction - straight narrow channel - expansion flow domain. The pressure drop is investigated especially when the droplet flows in the straight narrow channel. We explore the effects of droplet size, capillary number (Ca), viscosity ratio ($\chi$) between droplet and medium, and fluid elasticity represented by the Oldroyd-B constitutive model on the excess pressure drop (${\Delta}p^+$) against single phase flow. The tightly fitted droplets in the narrow channel are mainly considered in the range of $0.001{\leq}Ca{\leq}1$ and $0.01{\leq}{\chi}{\leq}100$. In Newtonian droplet/Newtonian medium, two characteristic features are observed. First, an approximate relation ${\Delta}p^+{\sim}{\chi}$ observed for ${\chi}{\geq}1$. The excess pressure drop necessary for droplet flow is roughly proportional to $\chi$. Second, ${\Delta}p^+$ seems inversely proportional to Ca, which is represented as ${\Delta}p^+{\sim}Ca^m$ with negative m irrespective of $\chi$. In addition, we observe that the film thickness (${\delta}_f$) between droplet interface and channel wall decreases with decreasing Ca, showing ${\delta}_f{\sim}Ca^n$ Can with positive n independent of $\chi$. Consequently, the excess pressure drop (${\Delta}p^+$) is strongly dependent on the film thickness (${\delta}_f$). The droplets larger than the channel width show enhancement of ${\Delta}p^+$, whereas the smaller droplets show no significant change in ${\Delta}p^+$. Also, the droplet deformation in the narrow channel is affected by the flow history of the contraction flow at the entrance region, but rather surprisingly ${\Delta}p^+$ is not affected by this flow history. Instead, ${\Delta}p^+$ is more dependent on ${\delta}_f$ irrespective of the droplet shape. As for the effect of fluid elasticity, an increase in ${\delta}_f$ induced by the normal stress difference in viscoelastic medium results in a drastic reduction of ${\Delta}p^+$.

• Asian-Australasian Journal of Animal Sciences
• /
• v.6 no.1
• /
• pp.107-113
• /
• 1993

This study determined the concentrations of micro-minerals in pastures, in feed supplements and in grazing, reproducing ewes, at different times during the year, at three farms in Northern China. Samples were collected 5 to 8 times during the year and analysed for selenium, copper, iron, molybdenum and zinc. On two farms selenium concentrations in both pastures and animal tissues were low for part of the year. The lowest concentrations in pasture (< $30{\mu}g/kg$ DM) and liver (< $100{\mu}g/kg$ wet weight) indicated that productivity of the sheep may be reduced by a deficiency of this element. On one farm copper concentrations in the lever were in the liver were in the deficient range (< $5{\mu}g/kg$ wet weight) for part of the year. It is likely that this is a result of high intakes of iron from pasture (up to 4.5 g Fe/kg DM) and soil, as indicated by high concentrations of iron in faeces (up to 7 g Fe/kg DM). Molybdenum intake is unlikely to have had much influence on copper absorption because pasture concentrations of this element were not unusually high (1 to 5 mg/kg DM). Zinc in pastures on two farms was below 10 mg/kg DM for part of the year. On one of these farms, the concentration of zinc in faeces was below 30 mg/kg DM throughout the year and this is consistent with zinc intakes of 7 to 15 mg/kg. Despite these low intakes, the concentratons of zinc in plasma were consistently above deficient levels. No clinical signs of deficiencies of any of the elements studied were observed.

• Restorative Dentistry and Endodontics
• /
• v.34 no.1
• /
• pp.69-79
• /
• 2009

The purpose of this study was to evaluate the influence of elastic modulus of restorative materials and the number of interfaces of post and core systems on the stress distribution of three differently restored endodontically treated maxillary second premolars using 3D FE analysis. Model 1, 2 was restored with a stainless steel or glass fiber post and direct composite resin. A PFG or a sintered alumina crown was considered. Model 3 was restored by EndoCrown. An oblique 500 N was applied on the buccal (Load A) and palatal (Load B) cusp. The von Mises stresses in the coronal and root structure of each model were analyzed using ANSYS. The elastic modulus of the definitive restorations rather than the type of post and core system was the primary factor that influenced the stress distribution of endodontically treated maxillary premolars. The stress concentration at the coronal structure could be lowered through the use of definitive restoration of high elastic modulus. The stress concentration at the root structure could be lowered through the use of definitive restoration of low elastic modulus.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.3
• /
• pp.159-165
• /
• 2021

This study introduces a topology optimization method for the simultaneous design of macro-scale structural configuration and unit structure variation to ensure effective heat conduction. Shape changes in the unit structure depending on its location within the macro-scale structure result in micro- as well as macro-scale design and enable better performance than using isotropic unit structures. They result in functionally graded composite structures combining both configurations. The representative volume element (RVE) method is applied to obtain various thermal conductivity properties of the multi-material based unit structure according to its shape change. Based on the RVE analysis results, the material properties of the unit structure having a certain shape can be derived using machine learning. Macro-scale topology optimization is performed using the traditional solid isotropic material with penalization method, while the unit structures composing the macro-structure can have various shapes to improve the heat conduction performance according to the simultaneous optimization process. Numerical examples of the thermal compliance minimization issue are provided to verify the effectiveness of the proposed method.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.6
• /
• pp.541-554
• /
• 2023

The utilization of underground spaces in relation to tunnels and energy/waste storage is on the rise. To ensure the stability of underground spaces, it is crucial to reinforce rock fractures and discontinuities. Discontinuities, such as joints, can weaken the strength of the rock and lead to groundwater inflow into underground spaces. In order to enhance the strength and stability of the area around these discontinuities, rock grouting techniques are employed. However, during rock grouting, it is impossible to visually confirm whether the grouting material is being smoothly injected as intended. Without proper injection, the expected increases in strength, durability, and degree of consolidation may not be achieved. Therefore, it is necessary to predict in advance whether the grouting material is being injected as designed. In this study, we aimed to assess the injection performance based on injection variables such as the water/cement mixture ratio, injection pressure, and injection flow using UDEC (Universal Distinct Element Code) numerical program. Additionally, numerical results were validated by the lab experiment. The results of this study are expected to help optimize variables such as injection material properties, injection time, and pump pressure in the grouting design in the field.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5B
• /
• pp.985-991
• /
• 2000

In this paper, the optimum structure of 2GHz magnetic thin film planar inductor were designed and fabricated to reduce the inductor area and to maximize the inductance L and quality factor Q of the inductor. The optimum design was performed utilizing Co90Fe10 layer multilayered with SiO2 layers to avoid the eddy-current skin effect and considering new lumped element model. New magnetic thin film inductors operating at 2GHz were fabricated on a Si substrate utilizing photo-lithography and lift-off techniques. The frequency characteristics of L, Q, and impedance in more than fifty identical inductors were measured using an RF Impedance Analyzer(HP4291B with HP16193A test fixture). The self-resonant frequencies(SRF) of the inductors were measured by a Vector Network Analyzer(HP8510). The developed inductors have SRF of 1.8 to 2.3GHz, L of 47 to 68nH, and Q of 70 to 80 near 1GHz. Finally, high frequency, high performance, planar micro-inductor(area=30.8 x 30.8il$^2$) with maximized L and Q were fabricated succefully.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.5
• /
• pp.575-582
• /
• 2010

In recent years, several rapid-mold-heating techniques that can be used for the injection molding of thin-walled parts or micro/nano structures have been developed. High-frequency induction heating, which involves heating by electromagnetic induction, is an efficient method for the rapid heating of mold surfaces. The present study proposes an integrated numerical model of the high-frequency induction heating process and the resulting injection molding process. To take into account the effects of thermal boundary conditions in induction heating, we carry out a fully integrated numerical analysis that combines electromagnetic field calculation, heat transfer analysis, and injection molding simulation. The proposed integrated simulation is extended to the injection molding of a thin-wall part, and the simulation results are compared with the experimental findings. The validity of the proposed simulation is discussed according to the ways of the boundary condition imposition.

• Korean Institute of Interior Design Journal
• /
• v.22 no.6
• /
• pp.3-10
• /
• 2013

This study intends to clarify the key elements of designing low energy residential building construction by planning out residential construction in nature oriented designing method utilizing nearby environment and nature oriented energy from designing stage instead of construction of low energy residential building. Development of building technology is proportional to the development of technology that lasts already. However, what is no less important than the advancement of technology, it is the study of fundamental phenomena energy use in response to climate, reduction, such as recycling. It is possible in such a purpose, it is assumed that there is a need to study elements implementation plan in accordance with the climatic characteristics of the study. Method for controlling the condition solar radiation, sunshine, depending on the characteristics of the weather, by utilizing the convection phenomenon of nature, to maintain the air comfort in the interior space is the essence of eco-friendly construction and passive Property This is an important architectural elements to be aim. For through the analysis of this case, corresponding to the phenomenon of the features of the macro climate and micro climate due to climate change, a combination building blocks of classification placement of each, shape, structure, elevation, space, of the material appeared in various it was possible to know the construction characteristics were. As shown in each case, construction method to address climate change has been found to apply to a comprehensive analysis climatic characteristics of each region, in response to this, the construction of element each corresponding.