• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.1
• /
• pp.7-17
• /
• 1997

During the past decade, there were many well-established theories for the adaptive control of linear systems, but there exists relatively little general theory for the adaptive control of nonlinear systems. Adaptive control technique is essential for providing a stable and robust performance for application of industrial robot control. Neural network computing methods provide one approach to the development of adaptive and learning behavior in robotic system for manufacturing. Computational neural networks have been demonstrated which exhibit capabilities for supervised learning, matching, and generalization for problems on an experimental scale. Supervised learning could improve the efficiency of training and development of robotic systems. In this paper, a new scheme of adaptive-neuro control system to implement real-time control of robot manipulator using digital signal processors is proposed. Digital signal processors, DSPs, are micro-processors that are developed particularly for fast numerical computations involving sums and products of variables. The proposed neuro control algorithm is one of learning a model based error back-propagation scheme using Lyapunov stability analysis method. The proposed adaptive-neuro control scheme is illustrated to be an efficient control scheme for implementation of real-time control for SCARA robot with four-axes by experiment.

• The Journal of the Korea Contents Association
• /
• v.16 no.8
• /
• pp.671-680
• /
• 2016

This research suggested a new real-time traffic signal control algorithm using fusion data of the travel time and the occupancy rate. This research applied the travel time data of traffic information system to traffic signal operation, and developed the signal control process using the degree of saturation that was estimated from the travel time data. This algorithm estimates a queue length from the travel time based on a deterministic delay model, and includes the process to change from the queue length to the degree of saturation. In addition, this model can calculate the traffic signal timings using fusion data of the travel time and the occupancy rate based on the saturation degree. The micro simulation analysis was conducted for effectiveness evaluation. We checked that the average delay decreased by up to 27 percent. In addition, we checked that this signal control algorithm could respond to a traffic condition of oversaturation and detector breakdown effectively and usefully. This research has important contribution to apply the traffic information system to traffic signal operation sectors.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.1
• /
• pp.31-40
• /
• 2008

This paper presented the development and real-time control of a magnetostrictive micro actuator. Magnetostrictive material has many advantages such as high response time, precision displacement and powerful output force. But Magnetostrictive material has characteristic of hysteresis. Conventional Preisach model which based on experimental data is not suitable to the real-time control because of controlling a magnetostrictive system by Preisach model costs a lot of calculating time. And, we prove the validity of proposed model through the experimental comparison between the classical Preisach model and the proposed one.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.3
• /
• pp.6-12
• /
• 2011

Electric vehicles and robots are real-time distributed control systems composed of multiple drive subsystems using micro controller units. Each control subsystem should be modular, compact, power saving, interoperable and fault tolerable in order to be incorporated into the networked real-time distributed control system. Under the networked real-time distributed control the synchronization problem can be occurred to the position and orientation tracking control due to the load variance, mismatch and time delay between the multiple drive subsystems. This paper suggests two types of position synchronization control of the single link manipulators. One of them is composed of cross controller, Kalman filter and disturbance observer, and the other uses the generation of target trajectories to minimize the gradient vector of the scalar function which is composed of the sum of square errors between the reference input vector and the output vectors. The availability of the proposed control schemes is shown through the control experiments.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.1
• /
• pp.3-6
• /
• 2008

Electrical discharge machining (EDM) is one of the most widespread nonconventional machining processes. Recently, a low-power micro-EDM process was introduced using a cylindrical electrode. Since its development, micro-EDM has been applied effectively to micromachining, and because the device setup for this process is simple, it is suitable for a microfactory that minimizes machines to fabricate small products economically in one system. In the EDM process, however, the electrode is also removed along with the workpiece. Therefore, the electrode shape and length vary as machining progresses. In this paper, a control method using a high speed realtime voltage measurement is proposed to regulate the rate and amount of material removed. The proposed method is based on the assumption that the volume of the workpiece removed in a single discharge pulses is nearly constant. The discharge pulses are monitored and controlled to regulate the amount of material removed. For this purpose, we developed an algorithm and apparatus for counting the number of discharge pulses. Electrode wear compensation using pulse number information was applied to EDM milling in a microfactory, in which a slight tilt of the workpiece may occur. The proposed control method improves the machining quality and efficiency by eliminating the inaccuracies caused by electrode wear and workpiece tilt.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1179-1181
• /
• 1992

A discrete Pl controller is implemented easily using a micro-processor, and it can be confirmed to a adaption of a system and real time processing. In this paper, a speed controller by discrete Pl control using a IBM PC/AT(12MHz) as a micro-processor is implemented and applied to a DC servo motor. In designing the discrite Pl controller, a sampling time and a speed is accepted from key-board, and is processed the control coefficient automatically, and than calculate the gain. Therefore the speed of a DC servo motor is obtained and controlled regulaly. The designed and manufactured discrete Pl control system is experimented. The result shows the good response at the 60 RPM to 250 RPM on the load using the load-spring. The speed error is under 1% on the steady load, but nearly 2-3% on the transient load.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.37 no.1
• /
• pp.33-40
• /
• 2014

Air compressor is an important facility with electric power in the industry. However, because of the noise and vibration of air compressor and is installed outside the building management difficulty. In this study, MCP (Micro Control Processor) to remote monitoring of the air compressor via the compressed air through improved quality and allows stable maintenance were designed. So, increase the productivity improvement of energy-saving effect can be obtained. Remote real-time information stored on your PC to manage air compressor equipment was higher reliability. Monitoring system is developed in this study was applied to embedded systems. It is easy to install air compressor, and low maintenance costs was to raise the economic impact.

• Proceedings of the KWS Conference
• /
• 1995.10a
• /
• pp.3-20
• /
• 1995

Development of Real-Time Quality Evaluation of Friction Welding by Acousitc Emission : Report 1 ABSTRACT : According as the friction welding has been increasingly applied in manufacturing various machine components because of its significant economic and technical advantages, one of the important concerns is the reliable quality monitoring method for a good weld quality with both joint strength and toughness in the process of its production. However no reliable nondestructive test method is available at present to determine the weld quality particularly in process of production. So this paper presents an experimental examination and quantitative analysis for the real-time evaluation of friction weld quality by acoustic emission, as a new approach which attempts finally to develop an on-line quality monitoring system design for friction welds using AE techniques. As one of the important results, it was confirmed, through this study, that AE techniques can be reliably applied to evaluating the friction weld qualify with 100% joint strength, as the cumulative AE counts occurring during welding period were quantitatively correlated with reliability at 95% confidence level to the joint strength of welds. Real-Time Evaluation of Automatic Production Quality Control for Friction Welding Machine : Report 2 Abstract : Both in-process quality control and high reliability of the weld is one of the major concerns in applying friction welding to the economical and qualified mass-production. No reliable nondestructive monitoring method is available at present to determine the real-time evaluation of automatic production quality control for friction welding machine. This paper, so that, presents the experimental examinations and statistical quantitative analysis of the correlation between the initial cumulative counts of acoustic emission(AE) occurring during plastic deformation period of the welding and the tensile strength of the welded joints as well as the various welding variables, as a new approach which attempts finally to develop an on-line (or real-time) quality monitoring system and a program for the process of real-time friction welding quality evaluation by initial AE cumulative counts. As one of the important results, it was well confirmed that the initial AE cumulative counts were quantitatively and cubically correlated with reliability of 95% confidence level to the joint strength of the welds, bar-to-bar (SCM4 to SUM31, SCM4 to SUM24L) and that an AE technique using initial AE counts can be reliably applied to real-time strength evaluation of the welded joints, and that such a program of the system was well developed resulting in practical possibility of real-time quality control more than 100% joint efficiency showing good weld with no micro-structural defects.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.499-500
• /
• 2006

The electrode wear in micro-EDM significantly deteriorates the machining accuracy. In this regard, electrode wear needs to be compensated in-process to improve the product quality. Therefore, there are substantial amount of research about electrode wear. In this study a control method for micro-EDM using discharge pulse counting is proposed. The method is based on the assumption that the removed workpiece volume is proportional to the number of discharge pulses, which is verified from experimental results analyzing geometrically machined volume according to various number of discharges. Especially, the method has an advantage that electrode wear does not need to be concerned. The proposed method is implemented to an actual micro-EDM system using high speed data acquisition board, simple counting algorithm with 3 axis motion system. As a result, it is demonstrated that the volume of hole machined by EDM drilling can be accurately estimated using the number of discharge pulses. In EDM milling process a micro groove without depth variation caused by electrode wear could be machined using the developed control method. Consequently, it is shown that machining accuracy in drilling and milling processes can be improved by using process control based on the number of discharge pulses.

• The Journal of Korea Robotics Society
• /
• v.9 no.3
• /
• pp.154-159
• /
• 2014

The Global Positioning System (GPS) is widely used to aid the navigation of aerial vehicles. However, the GPS cannot be used indoors, so alternative navigation methods are needed to be developed for micro aerial vehicles (MAVs) flying in GPS-denied environments. In this paper, a real-time three-dimensional (3-D) indoor navigation system and closed-loop control of a quad-rotor aerial vehicle equipped with an inertial measurement unit (IMU) and a low-cost light detection and ranging (LIDAR) is presented. In order to estimate the pose of the vehicle equipped with the two-dimensional LIDAR, an octree-based grid map and Monte-Carlo Localization (MCL) are adopted. The navigation results using the MCL are then evaluated by making a comparison with a motion capture system. Finally, the results are used for closed-loop control in order to validate its positioning accuracy during procedures for stable hovering and waypoint-following.