• Transactions of Materials Processing
• /
• v.11 no.7
• /
• pp.601-607
• /
• 2002

Optically transparent materials such as fused silica, quartz and crystal have become important in the filed of optics and optoelectronics. Laser ablation continues to grow as an important technique for micromachining and surface modification of various materials, because many problems caused by direct contact between tools and workpiece can be avoided. Especially, laser ablation with excimer lasers enables fine micromachining of transparent materials such as fused silica, quartz and crystal, etc. In this study, laser-induced wet etching of fused silica in organic solution was conducted. KrF excimer laser was used as a light source and acetone solution of pyrene was used as etchant. Changing the number of laser pulses, micro holes of various depths are fabricated.

• Transactions of Materials Processing
• /
• v.12 no.6
• /
• pp.582-587
• /
• 2003

This paper is concerned with the mechanical property changes of the milli-size products manufactured by forward extrusion processes with square dies. Experiments are carried out with pure aluminum and pure copper billets. Extrusion ratio and knock-out pad are chosen as the important process parameters affecting the changes of mechanical properties such as shear strength and hardness. Shear strength tests with the extruded milli-size pin have shown the strong relation between victors hardness and shear strength in the neck of a stepped pin. As the extrusion ratio increases, the hardness on both the surface and the center line of a pin also increase. It is also noted that the hardness on the surface is a little higher than that on the center. The existence of knock-out pad in extrusion die causes the hardness in the neck of a extruded pin to increase. Finally, the approximated linear relations between shear strength and hardness of a pin are suggested.

• Journal of Information Technology Applications and Management
• /
• v.14 no.3
• /
• pp.169-178
• /
• 2007

The next generation mobile multimedia network is expected to provide higher-rate multimedia communication services to versatile mobile terminals moving in even higher speed. For achieving more efficient reusability of scarce radio resources and thereby accommodating more user population in this network, the smaller cell such as micro or pico cell structure is used. More efficient and faster hand-over schemes are necessary to prevent the degradation of QoS of multimedia services caused by hand-over processing delay and packet loss during frequent hand-over. This paper proposes a faster and more effective hand-over scheme for high-rate multimedia services in the future mobile multimedia networks. by utilizing the GPS information on the position of the mobile terminal and its estimated moving directions. The simulation results show that our proposed method provides a better performance than the conventional method.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.4
• /
• pp.112-118
• /
• 2008

In order to meet the optical performance in the process of the micro lens manufacturing with plastics, it is important to embody accuracy in shape and surface roughness to the intended design. Since it is difficult to machine exactly the mold core of lens fit to the designed shape, in this paper, a simple program using MATLAB is developed for shape correction of the mold core after first machining it. This program evaluates correction parameters(aspheric coefficients and curvature) and generates aspheric NC data for compensating the core surface in prior machining process. The program provides the way to manufacture plastic injection molding lens with aspheric shape of high precision, and is expected to be effective for correction and to shorten the processing time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.356-357
• /
• 2007

In this paper, we developed an integrated miniaturized device which acquires and transmits the signal of ECG an interested heartbeat and body's temperature and humidity. Using an amplifier circuit on the electrodes and the radio frequency transmission, the developed system dispenses with the use of cables among the electrodes, amplifier, and the post processing system. The sensor signals are transmitted to the RF-wireless terminal that was developed using the micro controller Aduc812, LCD, RF-module (frequency 424MHz, 9600-bps). In results, the developed system improves not only the signal-to-noise ration in dynamic ECG & and body's temperature and humidity measurement, but also the user convenience.

• Transactions of Materials Processing
• /
• v.21 no.1
• /
• pp.5-12
• /
• 2012

The weight of the bipolar plate is one of the crucial aspects of improving power density in PEMFC stacks. Aluminum alloys have good mechanical properties such as density, electrical resistivity, and thermal conductivity. Furthermore, using aluminum in a bipolar plate instead of graphite reduces the bipolar plate cost and makes machining easier. Therefore in this study, an aluminum alloy was selected as the appropriate material for a bipolar plate. Results from feasibility experiments with the aim of developing fuel cells consisting of Al bipolar plates with multiple channels are presented. Dynamic loading was applied and the formability of micro channels was estimated as a function of punch pressure and die radius. Sheets of Al5052 with a thickness of 0.3mm were used. For a die radius of 0.1mm the formability was optimized with a sine wave dynamic load of 90kN at maximum pressure and 5 cycles of a sine wave punch travel. The experimental results demonstrate the feasibility of the proposed manufacturing technique for producing bipolar plates.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.8
• /
• pp.94-99
• /
• 2000

In this study applied the general controller into th 16bit ordinary controller and recommand the simulator features the real system's propeties without DSP(Digital Signal Processing)-card. This simulator is designed to be synchronized in real time using A/D(Analog-Digital) convert and D/A(Digital-Analong) convert. In this study DSP card which is usually used for complex calculation is replaced with personal computer and designed to control, control-force using with the 16-bit micro processor.

• Journal of Sensor Science and Technology
• /
• v.31 no.4
• /
• pp.244-248
• /
• 2022

Recently, several studies on the development of superhydrophobic surfaces using various nano-sized carbon-based materials have been conducted. The superhydrophobic surfaces developed using carbon soot have advantages such as low processing cost and remarkable physical and chemical properties. However, their durability is low. To address this problem, in this study, a superhydrophobic surface with high durability and a multilayer structure was fabricated using ethanol vapor treatment. Candle soot was deposited on an aluminum substrate coated with paraffin wax, and a micro-nano multilayer structure with a size of several micrometers was fabricated via ethanol vapor treatment. The fabricated superhydrophobic surface was confirmed to have a contact angle of at least 156° and high durability. Finally, it was confirmed that ethanol vapor not only changed the nanostructure of carbon but also affected the durability of the structure.

• Transactions of Materials Processing
• /
• v.22 no.1
• /
• pp.23-29
• /
• 2013

In this study, a micro/nano-random-pattern-structure surface was machined by electric discharge machining (EDM) followed by replicating the EDM surface with a silicone elastomer having low energy and greater hydrophobicity. The variation of hydrophobicity was of prime interest and was examined as a function of the surface roughness of the replicated silicone elastomer. The hydrophobicity was evaluated by the water contact angle (WCA) measured on the relevant surface. For the experiments, the original surfaces were machined by die sinking electric discharge machining (DS-EDM) and wire cutting electric discharge machining (WC-EDM). The ranges of surface roughness were Ra $0.8{\sim}19{\mu}m$ for the DS-EDM and Ra $0.5{\sim}4.7{\mu}m$ for the WC-EDM. In order to fabricate a hydrophobic surface, the EDM surfaces were directly replicated using a liquid-state silicone elastomer, which was thermally cured. The measured WCA on the replicated surfaces for DS-EDM was in the range of $115{\sim}130^{\circ}$ and for WC-EDM the WCA was in the range of $123{\sim}150^{\circ}$. Additionally, the dynamic hydrophobicity was evaluated by measuring an advancing and a receding WCA on the replicated silicone elastomer surfaces.

• Journal of Advanced Navigation Technology
• /
• v.11 no.4
• /
• pp.408-414
• /
• 2007

Research advances in the areas of micro-sensor device and wireless network technology, has made it possible to develop energy efficient and low cost wireless sensor nodes. In this paper, the forward error control (FEC) scheme for lower power consumption and excellent BER(Bit Error Rate) performance during transmission propose in multi-hop wireless sensor network based on FSK modem. The FEC technique uses extra processing power related to encoding and decoding, it is need complex functions to be built into the sensor node. The probability of receiving a correct bit and codeword for relaying a frame over h nodes to the sink node is calculated as a function of channel parameter, number of hops, number of bits transmitted and the distance between the different nodes.