• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.325-325
• /
• 2008

스크린 프린팅에 의한 압전 후막은 MEMS 공정을 이용하여 마이크로 펌프, 마이크로 벨브, 마이크로 센서, 마이크로 로봇 등 여러 초소형 기계부품에 응용되고 있으며, Sol-Gel, PLD를 이용해 증착된 막 등에 비해 수십${\mu}m$의 비교적 두꺼운 막을 형성시킬 수 있는 장점을 가지고 있다. 그러나 실리콘 기판을 사용하여 스크린 프린팅으로 형성된 압전 후막의 경우, 공정상 바인더를 연소시키는 과정을 거치게 되므로, 밀집된(Dense) 구조를 가지는 막을 만들기가 어렵다. 이로 인해 스크린 프린팅에 의한 후막은 전기적 특성 및 기계적 특성이 떨어지는 경향이 있다. 본 연구에서는 스크린 프린팅에 의한 압전 후막의 밀집된 구조 및 특성을 향상시키기 위해 0.01Pb$(Mg_{1/2}W_{1/2})$O3-0.41Pb$(Ni_{1/3}Nb_{2/3})O_3-0.35PbTiO_3-0.23PbZrO_3$의 powder와 Attrition 밀링 처리된 powder를 비율별로 혼합하여 입자의 크기를 변화시켜 막의 충진 밀도를 향상시켰으며, 열처리 효과를 극대화시키기 위해 RTA(Rapidly Thermal Annealing)를 통해 열처리 하였다. Attrition 밀링에 의한 파우더를 각각 비율별로 100%, 50%, 25%로 혼합하여 만든 압전 세라믹 페이스트는 P-type(100)Si Wafer sample 위에 $1{\mu}m$의 하부전극용($1100^{\circ}C$) Ag 전극을 screen print하여 소결했다. 그리고 다시 전극이 형성된 Si wafer 위에 스크린 프린팅하고, 건조 한 후 RTA로 300초 동안 열처리 한 결과 밀집된 구조를 가지는 압전 후막을 제작 수 있었다.

• Journal of Acupuncture Research
• /
• v.27 no.6
• /
• pp.31-42
• /
• 2010

Objectives : The aim of this study was to investigate the anti-obesity potential and mechanisms of action of Rhizoma Atractylodis(RA) herbal acupuncture in high fat diet- induced obese ICR mice. Methods : Sample solutions for herbal acupuncture were prepared from the Rhizoma Atractylodis water extract powder at concentration of 150mg/kg and 300mg/kg with distilled water. Five week-old ICR mice acclimatized to the laboratory environment for 1 week were allocated into four groups: regular diet group (RD), high fat diet group(HFD), groups fed HFD with 150mg/kg RA herbal acupuncture treatment (RAE 150) and with 300mg/kg RA herbal acupuncture treatment(RAE 300). Herbal acupuncture groups were injected with either 150mg/kg or 300mg/kg of Rhizoma Atractylodis(RA) subcutaneously onto both Sinsu($BL_{23}$) alternately on the same time everyday for 30days. Body weight, gross appearance of epididymal fat area, blood glucose, insulin, insulin resistance(HOMA-IR), non-esterified fatty acid, cholesterol, triglyceride, AST, ALT, histological analysis of white adipose tissue, gene expression responsible for adipocyte differentiation and AMPK activation were analyzed. Results : RA herbal acupuncture inhibited the development of weight gain, hyperglycemia, hyperinsulinemia, hyperlipidemia, increases of AST and ALT, and the enlargement of fat cell size induced by HFD. Also, RA herbal acupuncture inhibited the expression of PPAR-${\gamma}$, C/$EBP{\alpha}$, aP2, LPL, FAS, SCD-1 and enhanced the activation of AMP-activated protein kinase. Conclusions : The results of this study demonstrate that RA herbal acupuncture can exert the anti-obesity effect and it is partially mediated by activation of AMPK and inhibition of the gene expressions responsible for adipocyte differentiation. Further studies will be required to ascertain the nti-obesity effect and mechanisms of action of RA herbal acupuncture in animal models and human for aclinical application.

• Membrane Journal
• /
• v.22 no.5
• /
• pp.359-368
• /
• 2012

For hybrid water treatment of high turbidity water, we used the hybrid module that was composed of photocatalyst packing between tubular membrane outside and module inside. Photocatalyst was PP (polypropylene) bead coated with $TiO_2$ powder by CVD (chemical vapor deposition) process. Water back-flushing of 10 sec was performed per every period of 10 min to minimize membrane fouling for modified solution was prepared with humic acid and kaolin. Resistance of membrane fouling ($R_f$) decreased as humic acid concentration changed from 10 mg/L to 2 mg/L, and finally the highest total permeate volume ($V_T$) could be obtained at 2 mg/L, which was the same with the previous results. Then, treatment efficiencies of turbidity and humic acid were above 98.9% and 88.7%, respectively. As results of treatment portions of UF, UF + $TiO_2$, and UF + $TiO_2$ + UV processes, turbidity was treated little by photocatalyst adsorption, and photo-oxidation. However, treatment portions of humic acid by adsorption and photo-oxidation were 2.5% and 12.3%, respectively. Compared with the previous results, treatment portions of humic acid by adsorption and photo-oxidation were different depending on membrane material and pore size. As simplified the process, the membrane fouling resistance after 180 minutes' operation ($R_{f,180}$) increased and the final permeate flux decreased a little.

• Journal of the Korean Ceramic Society
• /
• v.35 no.9
• /
• pp.923-932
• /
• 1998

Al2O3/Al composites were produced by displacement reaction method which was carried out by imm-ersing the sintered silica preform which was prepared form fused silica powder in molten aluminu. an ac-tivation energy of 94kJ/mole was calculated from Al-SiO2 reaction data in 1000-130$0^{\circ}C$ temperature range With increase of reaction temperature the alumina particle in the Al2O3/Al composites produced with pur metal Al showed grain growth and the growth of alumina particle in Al2O3/Al composite produced by using of Mg contained Al alloy was inhibited. The flexural strength of Al2O3/Al composites produced at 100$0^{\circ}C$ showed the highest value as 393 MPa. Flexural strength of the composite fabricated at 85$0^{\circ}C$ showed higher deviation than that of the composite produced at above 100$0^{\circ}C$ Low flexural strength of the composite fa-bricated at 120$0^{\circ}C$ due to the growth of pore and alumina particle size. The hardness of composites de-pended on alumina content in Al2O3/Al composite decreased with increasing of aluminium content in case the same alumina content and increased with increasing of silicon content in composite.

• Journal of radiological science and technology
• /
• v.14 no.1
• /
• pp.49-60
• /
• 1991

Thermoluminescent phosphors, which are now being used widely in radiation dosimetry, have an excellent sensitivity to ionizing radiation. In this study, thermoluminescent phosphors of $CaSO_4$ : Mn, $CaSO_4$ : Dy and $CaSO_4$ : Tm are prepared and their physical properties are investigated by measuring the trapping parameters and their luminescent spectra. By considering the sensitivity to X-ray and fading characteristics, $CaSO_4$ : Dy is most adequate to imaging plate. The imaging plate are prepared by coating the $CaSO_4$ : Dy powder on the Al substrate and its dose dependence is linear within the range of 40 mGy-20 Gy X-ray. The sensitivity of imaging plate depends linearly on the thickness of coated phosphor layer up to $35\;mg/cm^2$ and is independent on the grain size of the phosphor in the range of $70{\sim}250\;{\mu}m$. By photographing the imaging plate, X-ray images of the test object are obtained and better than those of X-ray films.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.485-490
• /
• 2010

In our previous studies, continuous SiC fiber-reinforced SiC-matrix composites ($SiC_f$/SiC) had been fabricated by two different slurry infiltration methods: vacuum infiltration and electrophoretic deposition (EPD). 12 wt% of $Al_2O_3-Y_2O_3$-MgO with respect to SiC powder was used as additives for liquid-phase assisted sintering. After hot pressing at $1750^{\circ}C$ under 20 MPa for 2 h in Ar atmosphere, a high composite density could be achieved for both cases, whereas the problems such as large grain size and non-uniform distribution of liquid phase were observed, which was resulted in the relatively poor mechanical properties of composites. Therefore, efforts have been made to reduce the grain growth during the sintering, including the optimization for hot pressing condition and utilization of spark plasma sintering using a SiC monolith. Based on the results, spark plasma sintering was found to be effective method in decreasing the amount of sintering additive, time and grain growth, which will be explained in comparison to the results of hot pressing in this paper.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.147-150
• /
• 2011

A copper-based metal organic framework (MOF) named Cu-BTC, also known as HKUST-1, was successfully synthesized by using a solvothermal method. The properties of the Cu-BTC sample were characterized with Powder X-ray diffraction (XRD) for phase structure, Thermogravimetric analysis (TGA) for thermal stability, Scanning electron microscopy (SEM) for crystal structure, and Nitrogen adsorption-desorption for pore textural structure. The analysis results displayed that the Cu-BTC sample exhibited a good crystal structure with uniform size of octahedral particles. The BET data revealed a high surface area of $1457 \;m^2g^{-1}$ and a pore volume of $0.60\; cm^3g^{-1}$. The Cu-BTCs ample was also studied for $CO_2$ adsorption and exhibited a maximum $CO_2$ adsorption capacity of 170 mg/g of the sorbent (3.8 mol/kg) at $25^{\circ}C$.

• 한국전기화학회:학술대회논문집
• /
• 2003.07a
• /
• pp.189-192
• /
• 2003

In this work, we have prepared platinum catalyst by various methods, investigated fuel cell performance and compared performance with commercially available $20\%$ Pt supported on carbon (Pt/C) catalyst. We have found that Pt/C prepared by reduction of chloroplatinic acid in mixed solvent (water+ethylene glycol) gives better performance compared to that produced by reduction of aqueous chloroplatinic acid, which can be attributed to smaller catalyst particle size and lower agglomeration in the mixed solvent. We have also prepared a novel platinum electrocatalyst by depositing platinum on Nafion coated carbon powder and it shows great promise. The performance of electrode prepared using $20\%Pt$ onn Nafion coated carbon mixed with Pt/C was found to be higher than the performance of electrodes using commercially available $20\%$ Pt/C, up to a current density of about $1100mA/cm^2$. The cell voltages obtained were respectively 621 and 603mV, at a current density of: $1000mA/cm^2$, in a single cell using $0.25mgPt/cm^2$ and Nafion 10035 membrane at $80^{\circ}C$ using hydrogen/oxygen reactants at 1 atm pressure.

• Journal of the Korean Ceramic Society
• /
• v.17 no.2
• /
• pp.61-68
• /
• 1980

The effect of the addition of various fluoreides on the mullitization of Korean crude kaolin was studied by X-ray powder diffraction and scanning electron microscopic methods. Kaolin without any addition of fluoreides began to be transformed into the mullite at 1, 10$0^{\circ}C$. Mullite peaks were discernible in the X-ray diffraction patterns of the specimens which contained fluorides equivalent to about 2 wt % fluorine, and which were sintered at 1, 05$0^{\circ}C$. The higher the concentration of fluorine in kaolin, the lower was the initiatinig temperature of mullitization. Experiments , for example, showed that mullite could be formed at 95$0^{\circ}C$ from kaolin mixed with 3.4% fluorine. Of the fluoride, addtives, sodiumsiliconfluoride $(Na_2SiF_6)$ was must effective in mullite formation of kaolin. In order of accelerating mullitization, the fluorides except $Na_2SiF_6$ could be placed in following sequence ; (1) sodium (NaF) (2) aluminium$(AlF_3)$ (3)potassium(KF) (4) ammonium$(NH_4F)$ (5) magnesium$(MgF_2)$ (6) calcium$(CaF_2)$. It was considered that the intrinsic characteristics of fluorides, such as size of ionic radiu, charge , bond strength between cation and anion, and electronegativity of cation affected millitization of halloysite, a main constituent mineral of kaolin.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12a
• /
• pp.200-203
• /
• 2011

A copper-based metal organic framework (MOF) named Cu-BTC, also known as HKUST-1, was synthesized by using a solvothermal method at various synthesis temperature, time and pressure. The obtained samples were characterized with Powder X-ray diffraction (XRD) for phase structure, scanning electron microscopy (SEM) for crystal structure, and nitrogen adsorption-desorption for pore textural structure. The Cu-BTC sample was also studied for $CO_2$ adsorption. The analysis results displayed that the sample synthesized at the condition of temperature: $120^{\circ}C$, synthesis time: 12 hours, pressure: 1 bar exhibited a good crystal structure with uniform size of octahedral particles. The BET data revealed a high surface area of 1741.7 $m^2g^{-1}$ and a pore volume of 0.7137 $cm^3g^{-1}$and exhibiteda maximum $CO_2$ adsorption capacity of 170 mg/g of the sorbent at $25^{\circ}C$.