• 한국정밀공학회지
• /
• 제22권3호
• /
• pp.101-106
• /
• 2005

It needs to accumulate a store of know-how on the design, precision processing and appraisement for metering pump which is a kind of gear pump fer synthetic fibers. But the period and cost fur development is not effective, because designers experience many trial and error for the pump design and manufacturing process. Therefore, in order to curtail the period and cut down expenses, the analysis and simulation system is required for a designed metering pump. In this study, the pump simulation software was developed with the visual C++ language and the image processing algorithm, and was investigated through a discharge test for the planetary gear type metering pump.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1143-1147
• /
• 2004

A mechanical type pulsation dampener for the diaphragm metering pump has been developed. The pulsation pressure is an inevitable phenomenon for the positive displacement pump such as cam operated or solenoid operated metering pump. The pulsation pressure of the metering pump could be the noise source and would be harmful for the piping system which delivers hydraulic fluid. Developed pulsation dampener consists of three coil springs which have different spring constant and height each other. Depending on pressure magnitude of the piping system, total hydraulic pressure on damping diaphragm which compresses coil springs will be varied. Force equilibrium of the pulsation dampener will be set by manual by adjusting the compressed coil spring height. During the discharge stroke, pulsation dampener stores potential energy that is released as the pumping diaphragm back to an initial position during the suction stroke.

• 한국지열·수열에너지학회논문집
• /
• 제15권2호
• /
• pp.10-16
• /
• 2019

In this study, the present regulation of heat metering for the ground source heat pump was investigated. The ground source heat pump has been adopting the heat metering system used in the district heating system for estimating the heating and cooling energy production amount. The accuracy of the present heat metering systems for a water to water ground source heat pump is low, because the system for district heating has a relatively high temperature range comparing with the ground source heat pump operating conditions. Even though the heat amount for the building side should be measured, the heat absorption and extraction amount from or to the ground was measured for the water to air ground source heat pump due to the difficulty of estimating the air side heating and cooling capacity in the present regulation. It is highly recommended to validate the heat metering system to have reliability for the ground source heat pump and develop the system to be applicable water to air ground source heat pump.

• 동력기계공학회지
• /
• 제18권6호
• /
• pp.51-57
• /
• 2014

High pressure common rail injection technology has revolutionized the diesel industry. Over the last decade it has allowed engine builders to run higher injection pressures as much as above 1,300bar in order to increase engine efficiency, while reducing emissions. This common rail system has low pressure circuit which is consist of low pressure pump, cascade overflow valve and flow metering unit. The low pressure pump's purpose is to feed fuel oil to the high pressure pump. The cascade overflow valve keeps pressure in front of the metering unit constant and provides lubrication for the high pressure pump. The metering unit, known as the MPROP or fuel pressure regulator, regulates the maximum flow rate delivers to the rail. In this paper, we have investigated the performance characteristics of each components and total low pressure circuit of common rail system.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1997년도 동계 학술대회 논문집
• /
• pp.255-262
• /
• 1997

A low-cost and precise metering device, which is suitable to automatic mixing of nutrient-solution for hydroponic culture, was developed for small-scale growers. The metering device was composed of three parts those were supply pumps, metering cylinders and venturi tube. Those parts were controlled by personal computer with time-based odoff control method. To verify the performance of the developed metering device, the relationship between operating time and discharge was examined and the accuracy of the developed metering device was compared with commercial metering pumps. The results of this study are as follows. 1. The correlation coefficient between the flow rate and operating time was 0.9999, and the linear regression equation computed was y=21.759x, where y is the discharge(g) and x is the operating time(s). 2. The developed device has greater accuracy than commercial metering pumps in terms of the full-scale error. Calculated errors for the developed metering device and two commercial pump were $\pm$0.3 %, $\pm$2.45 % and $\pm$1.38 % respectively. 3. Above results show developed metering device is a useful tool for nutrient-solution control system.

• 원예과학기술지
• /
• 제16권1호
• /
• pp.25-26
• /
• 1998

본 연구는 정량펌프를 이용한 정확한 증산량 추정 시스템의 구축 및 측정된 증산량과 환경요인과의 관계를 분석하는 데 있다. 정량펌프에 의한 양액공급 및 증산량 추정 시스템은 매우 안정적인 특성을 나타냈으며, 증산량 추정을 위하여 재배 시스템에 설치한 정량펌프의 공급시간과 투입량과의 관계는 직선관계를 나타냈다. NFT 및 고형배지 시스템에서의 적산일사량과 증산량을 실측한 결과 증산량은 일사량에 직접적인 영향을 받고 있었으며, NFT는 상관계수 0.98. 고형배지는 상관계수 0.92의 높은 상관관계를 나타내었다. 따라서 정량펌프에 의한 증산량 추정은 양액급액 제어에 효율적인 방법이며, 이러한 방법을 사용하여 적산일사량에 의한 관수량 조절 및 비료투입량의 결정에 적용이 가능하다. 따라서, 측정된 적산일사량에 의하여 증산량 추정이 가능하기 때문에, 정량펌프에 의하여 필요 관수량을 정확한 공급할 수 있다.

• Design & Manufacturing
• /
• 제10권2호
• /
• pp.18-23
• /
• 2016

Injection molded thermoplastic parts may need to be coated to facilitate paint adhesion, or to satisfy other surface property requirements, such as appearance, durability, and weather resistance. In this paper, a two-component polyurethane metering system was developed for the simultaneous injection and surface coating of a plastic substrate. The system was composed of storage tanks, feed pumps, axial piston pumps, mixing head. The tank was designed to be double-jacket structured and fabricated for polyol and isocyanate, respectively. A temperature chamber was used to maintain the material temperature to be $80^{\circ}C$ during flowing from storage tank to mixing head. Inside the chamber, feed pump, low pressure filter, high pressure pump, high pressure filter, pressure sensor, flow meter were installed. A mixing head of L-type was used for homogeneous mixing of polyol and isocyanate. Inside the mixing head, a cartridge heater and a temperature sensor were installed to control the temperature of the materials. The flow rate of axial-piston pump was controlled by using closed-loop feedback control algorithm. The input flow-rates were compared with the measured values. The output error was 6.7% for open-loop control, whereas the error was below 2.2% for closed-loop control. In addition, the pressure generated through mixing-head nozzle increased with increasing flow rate. It was found that the pressure drop between metering pump and mixing-head nozzle was almost 10 bar.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.31-39
• /
• 1999

Previous researches and experiments have already verified that the primary noise source of high pressure tandem axial thpe piston pump is fluid-borne noise from the process of oil distribution between the kidney-shaped port and valve plate. So, many researchers have improved pressure gradients and reduced sound levels by applying pre-compression and pre-decompression metering grooves to valve plate. In practice however, the sound level of th high pressure tandem axial type piston pump is still undesirable. This paper testified the effect of pumping phase of the piston on vibration and noise of th high pressure tandem axial type piston pump on the best of theoretical research in $this^(1)$. Therefore considering the pumping phase of the piston when assembling the tandem axial type piston pump, it is possible to reduce 1.5~2[dB]of sound level.

• 한국산학기술학회논문지
• /
• 제18권10호
• /
• pp.102-109
• /
• 2017

디젤 분사시스템의 고압펌프는 저압으로 공급된 연료를 압축하여 고압 연료로 만들고 엔진 작동조건에 따라 커먼레일의 연료를 요구되는 압력수준으로 유지한다. 고압펌프는 차량의 전체 수명기간 동안 연료를 2000 bar에 달하는 고압으로 압축하여 원활히 동작해야 하므로 설계기술, 재료의 내구성, 고도의 가공정밀도가 요구된다. 이 연구에서는 1-플런저 레이디얼 피스톤 펌프 형태의 고압펌프에 대한 시뮬레이션 모델을 상용 소프트웨어인 AMESimpp의 서브 모델들을 이용하여 개발하고, 고압펌프의 동작특성을 살펴보기 위해 시뮬레이션을 실시한다. 주요한 시뮬레이션 내용들은 입구 및 출구 밸브의 변위, 유량, 압력 특성, 캠의 토크 특성, 그리고 연료 미터링밸브의 압력 제어 특성과 오버플로밸브의 동작 특성이다. 또한 입구 밸브의 구멍지름과 스프링 초기력 등의 파라미터 변화에 따른 입구 및 출구 밸브의 유량과 커먼레일 압력 등의 고압펌프의 동작 특성과 응답 특성을 시뮬레이션을 통해 검토한다. 이를 통해서 개발된 펌프 모델의 동작이 논리적으로 타당함을 제시하고, 고압펌프를 설계변경하거나 개발초기에 설계변수들의 설정과 튜닝에 활용할 수 있는 시뮬레이션 모델을 제안한다.

• Journal of Biosystems Engineering
• /
• 제22권4호
• /
• pp.469-478
• /
• 1997

This study was conducted to develop an automatic nutrient-solution mixing system for small-scale sewers. The nutrient-solution mixing system consisted of a low-cost and precise metering device and data acquisition ＆ control system with a personal computer. and, the metering device was composed of three parts those were supply pumps, metering cylinders and venturi tube. The system controlled electric conductivity(EC) and pH of nutrient-solution based on the time-based feedback control method with the information about temperature, EC, and pH of the nutrient-solution. The performance of the nutrient-solution mixing system was evaluated through the control of EC and pH while compared with those of commercial system. Also an experimental cultivation of tomato was conducted to verify and to improve the developed system. Results of this study were as follows. 1. The correlation coefficient of meteing device between the flow rate and operating time was 0.9999, and the linear reuession equation computed was y=21.759x, where y is the discharge($g$) and x is the operating time(s). 2. Calculated errors for the developed metering device and two commercial pump were $\pm$0.3% $\pm$2.45% and $\pm$1.38 % FS error respectively. 3. An automatic nutrient-solution mixing system based on a low-cost and precise metering device was developed. 4. The full scale errors of the developed system in controlling EC and pH at 23$\pm$1$^{\circ}C$ were $\pm$0.05mS/cm and $\pm$0.2, respectively 5. When using the commercial system, the controlled values of EC and pH of the 500 $\ell$ of water were 1.29 mS/cm and 6.1 pH for the setting points of 1.4 mS/cm and 6.0 pH respectively at 23$pm1^{\circ}C$. 6. The developed nutrient-solution control system showed $\pm$0.05 ms/cm of deviation from the setting EC value over the experimental cultivation period. 7. The deviation from the average values of Ca and Mg mass content in the several nutrient-solution were 0.5% and 1.8% respectively.