• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.458-464
• /
• 1998

This paper gives characterization of substrate and PZT(53/47) thin film deposited by metalorganic decomposition, which is concerned in deposition process and device fabrication process, to fabricate micro electro mechanical system (MEMS) device with piezoelectric material. The PZT thin films deposited by MOD at 700^{\circ}C$ for 30 minutes had a polycrystallinity, that is, no substrate dependence, while different interface were developed depending on the bottom electrodes. Such a structural variation could influence on not only the properties of the PZT film but also etching process for fabricating MEMS devices. Therefore the electrode structure is a very important factor in the deposition of the PZT film during etching process by HF acid for MEMS device with piezoelectric material. Piezoelectric coefficients of the PZT films on the different substrates were 40 and 80 pm/V at an applied voltage of 4V. Based in these results, it was possible for deposition of the PZT film by MOD to apply MEMS device fabrication process based on piezoelectricity after selection of proper bottom electrode.

• Journal of the Korean Vacuum Society
• /
• v.5 no.4
• /
• pp.354-358
• /
• 1996

High indium incorporation was observed in InGaAs growth by precursor alternating metalorganic chemical vapor deposition (PAMOCVD). A possible mechanism of high indium incorporation into the crystal in PAMOCVD was proposed by considering the decomposition products of gallium and indium precursors, and thus the different adsorption behavior of the decomposed precursor molecules.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.565-568
• /
• 2001

We have fabricated $Bi_{3.25}La_{0.75}Ti_{3}O_{12}(BLT)$ thin(200nm) films on the $Pt/Ti/SiO_{2}/Si$ substrates using a MOD(Metalorganic decomposition) method with annealing temperature from $550^{\circ}C$ to $750^{\circ}C$. The structural properties of the films examined by x-ray diffraction. The layered-perovskite phase obtained above $600^{\circ}C$. Scanning electron micrographs showed uniform surface composed of rodlike grains. The grain size increased with increasing annealing temperature. The BLT thin films showed little polarization fatigue test up to $3.5{\times}10^{9}$ bipolar cycling at a 5V and 100kHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.565-568
• /
• 2001

We have fabricated $Bi_{3.25}$$La_{0.75}$ti$_3$O$_{12}$ (BLT) thin(200nm) films on the Pt/Ti/SiO$_2$/Si substrates using a MOD(Metalorganic decomposition) method with annealing temperature from 55$0^{\circ}C$ to 75$0^{\circ}C$. The structural properties of the films examined by x-ray diffraction. The layered-perovskite phase obtained above $600^{\circ}C$. Scanning electron micrographs showed uniform surface composed of rodlike grains. The grain size increased with increasing annealing temperature. The BLT thin films showed little polarization fatigue test up to 3.5x10$^{9}$ bipolar cycling at a 5V and 100kHz.kHz.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.180.2-180
• /
• 2002

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.274-280
• /
• 1998

Polycrystalline $Sr_2Nb_2O_7$ ceramics with very high Curie temperature were sintered using the powder derived by the chemical coprecipitation method (CCP). The phase evolution and grain-orientation of sintered samples were examined by XRD, while sintering behavior, dielectric properties and polarization were studied by SEM and ferroelectric tester. Extremely high degree of grain-orientation was observed along the (0k0) direction, which resulted in anisotropic dielectric properties of the sintered samples, with the dielectric constant values approaching those for single crystal. Thin film fabrication of $Sr_2Nb_2O_7$ in the pyroniobate family was also attempted on $SiO_2$/Si(100), Pt/$SiO_2$/Si(100), Pt/Ti/$SiO_2$/Si(100) and Pt/$ZrO_2/SiO_2/Si_2(100)$ substrates, using metalorganic decomposition (MOD) process. Neodecanoate precursor solution was prepared by mixing strontium neodecanoate with niobium neodecanoate synthesized from niobium ethoxide. It was found that $Sr_2Nb_2O_7$ single phase appeared in XRD patterns the samples annealed above $950^{\circ}C$. The effect of substrate type on film microstructure and dielectric properties was observed.

• Journal of Korean Vacuum Science & Technology
• /
• v.6 no.2
• /
• pp.88-91
• /
• 2002

InGaN/GaN multiple quantum wells (MQWs) were grown by metalorganic chemical vapor deposition and their structural and optical properties were studied. When the average In content was increased by increasing TMIn flow rate, PL measurement showed little change in PL peak position and large increase in PL intensity instead. Large changes in PL peak position could be achieved by changing growth temperature. We propose the formation of fixed In content, highly In-rich quantum dot-like phases in InGaN MQWs driven by spinodal decomposition.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.100-100
• /
• 2000

Aluminium oxide (Al2O3) films have been investigated for many applications such as insulating materials, hard coatings, and diffusion barriers due to their attractive electrical and mechanical properties. In recent years, application of Al2O3 films for dielectric materials in integrated circuits as gates and capacitors has attracted much attention. Various deposition techniques such as sol-gel, metalorganic decomposition (MOD), sputtering, evaporation, metalorganic chemical vapor deposition (MOCVD), and pulsed laser ablation have been used to fabricate Al2O3 thin films. Among these techniques, reactive sputtering has been widely used due to its high deposition rate and easy control of film composition. It has been also reported that the sputtered Al2O3 films exhibit superior chemical stability and mechanical strength compared to the films fabricated by other processes. In this study, Al2O3 thin films were deposited on Pt/Ti/SiO/Si2 and Si substrates by DC reactive sputtering at room temperature with variation of the Ar/O2 ratio in sputtering ambient. Crystalline phase of the reactively sputtered films was characterized using X-ray diffractometry and the surface morphology of the films was observed with Scanning election microscopy. Effects of Th Ar/O2 ratio characteristics of Al2O3 films were investigated with emphasis on the thickness dependence of the dielectric properties. Correlation between the dielectric properties and the microstructure was also studied

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.245-248
• /
• 2003

Randomly oriented ferroelectric cerium-substituted $Bi_4Ti_3O_{12}$ thin films have been prepared by using metal-organic decomposition method. The layered perovskite structure was investigated using annealing for 1 h in the temperature range from $550\;{\sim}\;750\;^{\circ}C$. The structure and morphology of the films were characterized using X-ray diffraction and scanning electron microscopy The $Bi_{3.4}Ce_{0.6}Ti_3O_{12}$ (BCeT) thin films showed a perovskite phase and dense microstructure. The grain size of the BCeT films increasedwith increasing annealing temperature. The hysteresis loops of the films were well defined at temperatures above $600\;^{\circ}C$. The 200-nm-thick BCeT thin films annealed at $650\;^{\circ}C$ showed a large remanent polarization (2Pr) of 59.3 ${\mu}C/cm^2$ at an applied voltage of 10 V. The BCeT thin films showed good fatigue endurance up to $5\;{\times}\;10^9$ bipolar cycling at 5 V and 100 kHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.352-355
• /
• 2003

[ $Bi_{3.25}La_{0.75}Ti_3O_{12}$ ] (BLT) thin films were prepared by using metal organic decomposition method onto the LaNiO3 (LNO) bottom electrode. Both the structure and morphology of the films were analyzed by x-ray diffraction (XRD) and atomic force microscope (AFM). Even at low temperatures ranging from 450 to $650^{\circ}C$, the BLT thin films were successfully deposited on LNO bottom electrode and exhibited (117) orientation. The BLT thin films annealed as low as $600^{\circ}C$ showed excellent ferroelectricity, higher remanent polarization and no significant degradation of switching charge at least up to $5{\times}10^9$ switching cycles at a frequency of 100 kHz and 5 V. For the annealing temperature of $600^{\circ}C$, the remanent polarization $P_r$ and coercive field were $23.5\;{\mu}C/cm^2$ and 120 kV/cm, respectively.