• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.128-129
• /
• 2006

To investigate impact property characteristics on the low temperature plate weld metal, the two different plates of the same steel grade were welded and evaluated by Mo bearing and no Mo containing welding consumables. The results are summarized as follows; 1) Multi pass welded Mo bearing weldment was not satisfied with the requirement of tensile strength, while no Mo containing one was satisfied with it 2) In the plate butt weldment, the impact property of weld metal was highly affected by both the welding consumable and plate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.151-154
• /
• 2002

In this paper a mathematical model, the results of computer simulation and exprimental investigations of electrochemical machining with a too-electrode are presented. The experimental investigations were carried out in order to evaluate the influence of working voltage, initial interelectrode gap size, and metal remove rate. Accuracy of computer simulation evaluated by differences between results of experimental test and computer simulation depends on electrochemical machining coefficient, total overpotential of electrode process, current density, electrical conductivity of electrolyte, and etc. Metal removal rate would be predicted by the simulation of ECM process.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.354-358
• /
• 1996

At design stage of the TRXI agricultural tractor transmission (New product of TongYang Moolsan Co., Ltd), the noise and vibration of the transmission were analyzed theoretically for the optimal design of the transmission . For this analysis, the finite element model was developed using a commercial computer software, ANSYS. The noise and vibration of the TRXI transmission housing were predicted by the modal analysis. Natural frequency of the TRXI transmission housing was ranged from 12.53Hz(1st mode ) to 30.05Hz(5th mode). The fifth mode took place at the bearing metal in the area of rear transmission housing and was very close to the gear mesh frequency (30.5Hz) of low rang gear at the low creep shifting . Based on the results , the bearing metal of the range shift housing was reenforced with the rib at design stage.

• 국제학술발표논문집
• /
• The 5th International Conference on Construction Engineering and Project Management
• /
• pp.274-278
• /
• 2013

Over the past several years, the building codes that govern commercial building construction have become increasingly prescriptive in nature, specifying detailed information related to the design and installation of the systems, while offering no reasoning behind their prescriptive measures. For example, metal stud framing is commonly used in commercial building construction to create bearing walls and non-bearing partition walls. BIM provides a powerful platform for developing and implementing "pre-planning" tools and methods to facilitate both engineering and administrative controls during construction. This paper discusses the use of BIM to enhance constructability for commercial building construction activities, specifically metal stud framing. Using specific real-world examples this paper demonstrates ways that BIM can be used to foresee potential construction issues and motivates and informs future uses of BIM technologies

• 한국전산구조공학회논문집
• /
• 제30권4호
• /
• pp.313-318
• /
• 2017

본 연구는 진동에너지를 흡수하기 위한 진동 금속 댐퍼의 구조 해석과 최적 설계를 수행한다. 고무 베어링, 마찰 또는 점성 댐퍼와 같은 다른 댐퍼와는 달리 이 금속제진장는 금속의 소성 변형과 그에 따른 히스테리시스 현상을 이용하여 구조물의 진동을 감소시킨다. 이 금속제진장치를 최적화 하려면 댐퍼를 통해 소성 변형을 얻는 것이 중요하다. 금속제진장치의 최적화된 형상을 찾기 위해 형상 최적화 방법을 적용하였다. 또한 매개 변수화 체계에 따라 일부 최적의 모양을 찾을 수 있다.

• 한국강구조학회 논문집
• /
• 제16권5호통권72호
• /
• pp.599-607
• /
• 2004

건물이 고층화되어 가면서 철골구조 사용이 빈번해지고 있으며 철골구조물의 큰 축력을 받는 기둥에 있어서 이음부 설계가 중요한 문제가 되고 있다. 한편, 미국 AISC 기준에서는 기둥이음에서 지압내력으로 모든 압축축력을 전달할 수도 있으나, 우리나라 기준에서는 소요압축축력의 1/4만을 접촉면에 의해 직접전달 시킬 수 있다고 제한함에 따라 메탈터치를 활용한 기둥이음에 대한 새로운 방법의 개발이 제한되고 있는 실정이다. 따라서 본 논문에서는 기존 볼트, 용접 체결된 실험체에 이음부 틈의 크기를 매개변수로 하는 실험체의 응력전달체계를 규명하고, 메탈터치 정도에 따른 철골기둥 이음부의 압축축력전달 메카니즘을 검증한다. 또한 해석과 실험을 통하여 틈의 크기에 따른 거동 양상을 파악하여 메탈터치에 의한 이음부에서의 응력전달체계에 대한 확인과 이론적 기초를 제시하고자 한다.

• 한국분말재료학회지
• /
• 제19권2호
• /
• pp.140-145
• /
• 2012

This paper describes the manufacturing process of tilting pad gas bearing with a diameter of 5 mm and a length of 0.5-1 mm for power MEMS (Micro Electomechanical Systems) applications. The bearing compacts with nanopowder feedstock were prepared by Ni-metal mold with 2-mold system using LIGA process. The effect of the manufacturing conditions on sintering properties of nanopowder gas bearing was investigated. In this work, Fe-45 wt%Ni nanopowder with an average diameter of 30-50 nm size was used as starting material. After mixing the nanopowder and the wax-based binders, the amount of powder was controlled to obtain the certain mixing ratio. The nanopowder bearing compacts were sintered with 1-2 hr holding time under hydrogen atmospheres and under temperatures of $600^{\circ}C$ to $1,000^{\circ}C$. Finally, the critical batch of mixed powder system was found to be 70% particle fraction in total volume. The maximum density of the sintered bearing specimen was about 94% of theoretical density.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권3호
• /
• pp.105-109
• /
• 2001

In this paper, the windmill type ultrasonic motors with 11.35 mm diameter, 2.87 mm thickness of metal endcap and 1.47 g weight were fabricated. Effects of slots and thickness on torque characteristic in the windmill type ultrasonic motor were investigated, when stator's slots were changed from 4, 6, 8 and thickness 0.15 mm, respectively. Specially designed metal endcaps with windmill shaped cutting can provide longitudinal and torsional displacements simultaneously as the ceramic disk vibrates radically. The windmill type ultrasonic motor has only three components: a stator element with windmill shape slotted metal endcap, a rotor and bearing. Ultrasonic motor stimulated to ultrasonic oscillations by piezoelectrics to drive a rotor via friction contact. The ultrasonic motor fabricated here was the windmill type ultrasonic motor operated by single-phase AC source. Bidirectional revolution using single-phase high frequency for driving the ultrasonic motor was presented.

• 한국자원리싸이클링학회:학술대회논문집
• /
• 한국자원리싸이클링학회 2005년도 제13회 산화철워크샵
• /
• pp.3-14
• /
• 2005

We Investigated minutely how the biosorption technology using algal biomass is opened in Canadian technology society. Making comparative study for relative technologies in views of overall unit operation cost, we could grasp next facts. - Algal biomass plays the competitive performance for various metals. - Algal biomass biosorbent is regenerated. - Reactor system is not and involved one. This means that algal biomass occupies the strong position as biosorbent. Especially, in North America, for the purpose of metal bearing wastewater treatment, 20 hundred million US dollars was appropriated a sum for the purchase of ion exchange resin. But it is only thirty million US dollars if algal biomass biosorbent is used on behalf of ion exchange resin. Furthermore, the expenses for same treatment can be cut down additively through metal recovery.

• 대한치과보철학회지
• /
• 제39권1호
• /
• pp.1-13
• /
• 2001

An absolutely passive fit at the interface with the superstructure and the abutment cylinders is need for implant longevity. In this study, a method of cast framework correction using spark erosion technology was evaluated. Electric discharge machining(EDM) is a process that uses electrical discharges, or sparks, to machine metal, The surface being machined is bombared with high-intensity electrical energy pulses that gradually melt away the stock until the desired configuration is obtained. Master model was fabricated by using metal block impression analogue, which fired 5 Branemark squared impression coping in an arc shaped metal block. Then framework using 4mm standard gold cylinder and type IV gold alloy was fabricated. In order to measure the fit of the framework we used both contact and noncontact coordinate measurement machine and data was processed by computer program. After superimposition of gold framework and master model numeric image data the distances between gold cylinder bearing surfaces and abutment replica bearing surfaces, and the angle deviations between gold cylinder and abutment replica centroid points were calculated. The results were as follows 1 The total mean distance (p<0.01) and standard deviation (p<0.001) between the gold cylinders and abutment bearing surfaces were significantly decreased after EDM 2. The total mean of maximum distances was significantly decreased after EDM (p<0.05). 3. After EDM, the mean angle deviation between centroid points was decreased.