• 대한금속재료학회지
• /
• 제50권1호
• /
• pp.52-58
• /
• 2012

Hydrogen-delayed fracture (HDF) was analyzed from the deposited weld metals of 600-MPa and 800-MPa flux-cored arc (FCA) welding wires, and then from the diffusible hydrogen behavior of the weld zone. Two types of deposited weld metal, that is, rutile weld metal and alkali weld metal, were used for each strength level. Constant loading test (CLT) and thermal desorption spectrometry (TDS) analysis were conducted on the hydrogen pre-charged specimens electrochemically for 72 h. The effects of microstructures such as acicular ferrite, grain-boundary ferrite, and low-temperature-transformation phase on the time-to-failure and amount of diffusible hydrogen were analyzed. The fracture time for hydrogen-purged specimens in the constant loading tests decreased as the grain size of acicular ferrite decreased. The major trapping site for diffusible hydrogen was the grain boundary, as determined by calculating the activation energies for hydrogen detrapping. As the strength was increased and alkali weld metal was used, the resistance to HDF decreased.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제13권5호
• /
• pp.47-56
• /
• 2008

금속이 염 용액 형태로 토양에 유입될 때, 그 금속의 용해도는 시간이 지남에 따라 감소하는 경향(aging)을 보이는데, 이러한 시간 의존성 외에 토양 내 금속 용해도의 변화에 영향을 미치는 또 다른 요인들에 대한 고찰은 아직 미비한 상태이다. 본 연구에서는 물리화학적 성질이 다른 5 종류의 토양 (히스토졸, 앤디졸, 옥시졸, 미세입자 알피졸, 조대입자 알피졸)에 여러 비율의 카드뮴(2.5-20 mg ${kg}^{-1}$)/ 구리(50-400 mg${kg}^{-1}$)/ 아연(50-400 mg ${kg}^{-1}$) 염 용액을 혼합하여, 상온에서 1년 동안 토양의 성질, 금속의 종류, 금속의 농도에 따른 용해도 변화관찰을 시도하였다. 그 결과, 히스토졸에서는 카드뮴이, 앤디졸에서는 구리가, 미세입자 알피졸에서는 아연이 가장 높은 분배 계수를 보였고, 옥시졸과 조대입자 알피졸에서는 모든 금속들이 가장 낮은 분배 계수를 나타내었다. 또한, 카드뮴과 아연의 경우 토양의 종류와는 무관하게 시간에 따른 분배 계수의 증가를 보였지만, 구리의 경우 토양 내 유입된 후 일주일 부터는 이러한 경향성를 찾아보기 어려웠다. 구리는 토양의 유기물이 많을 경우에는 빠른 흡착성을 보이지만, 토양수에 녹아있는 유기물이 많을 경우에는 그 흡착 특성이 제한됨을 관찰하였다. 더욱이, 흡수력이 높은 토양의 경우 금속의 분배 계수는 유입된 금속의 양과는 무관할 뿐만 아니라, 높은 농도로 처리된 토양의 금속 분배 계수가 낮은 농도로 처리된 토양의 분배계수와 유사해지기 까지는 더 오랜 시간이 요구되는 반면, 낮은 흡수력을 가진 토양의 경우에는 시간보다는 금속의 초기 유입양이 분배 계수 결정에 더욱 큰 영향을 미치는 것으로 밝혀졌다. 본 연구를 통해, 토양에 유입된 금속의 용해도 변화는 시간 뿐만 아니라, 토양의 성질, 금속의 종류와 농도에도 상당히 의존함을 입증하였다.

• 소성∙가공
• /
• 제3권2호
• /
• pp.147-155
• /
• 1994

The service life of tools in metal forming technology is to a large extent limited by wear and fatigue fracture of the active elements. This presents a basic request for tool cost minimization and reduction of extensive machine down time, caused by premature tool failure. Currents developments are dominated by steps to reduce the causes of tool failure. A main problem of forming technology remains the insufficient reliability of tools due to a large and incalculable life time fluctuation. Only a systematic investigation of the failure mechanisms and operational loading of tools can lead to future improvements in tool layout, that is optimization of tool usage.

• 대한치과보철학회지
• /
• 제28권1호
• /
• pp.63-94
• /
• 1990

The purpose of this study was to analyze the displacement and the magnitude and the mode of distribution of the stresses in the lower overdenture, the mucous membrane, the abutment tooth and the mandibular supporting bone when various denture base materials, such as acrylic resin and 0.5mm metal base, and various denture base designs were subjected to different loading schemes. For this study, the two-dimensional finite element method was used. Mandibular arch models, with only canine remaining, were fabricated. In the first denture base design, a space, approximately 1mm thick, was prepared between the denture and the dome abutment. In the second denture base design, contact between the denture and the dome abutment was eliminated except the contact of the occlusal third of the abutment. In order to represent the same physiological condition as the fixed areas of the mandible under loading schemes, the eight nodes which lie at the mandibular angle region, the coronoid process and the mandibular condyle were assumed to be fixed. Each model was loaded with a magnitude of 10 kgs on the first molar region(P1) and 7 kgs on the central incisal region (P2) in a vertical direction. Then the force of 10 kgs was applied distributively from the first premolar to the second molar of each model in a vertical direction(P3). The results were as follows. : 1. When the testing vertical loads were given to the selected points of the overdenture, the overdenture showed the rotatory phenomenon, as well as sinking and the displacements of alveolar ridge, abutment and lower border of mandible under the metal base overdenture were less than those under the acrylic resin overdenture. 2. The maximum principal stresses(the maximum tensile stresses) being considered, high tensile stresses occured at the buccal shelf area, the posterior region of the ridge crest and the anterior border region of the mandibular ramus. 3. The minimum principal stresses(the maximum compressive stresses) being considered, high compressive stresses occured at the inferior and posterior border region of the mandible, the mandibular angle and the posterior border region of the mandibular ramus. 4. The vertical load on the central incisal region(P2) produced higher equivalent stress in the mandible than that on any other region(P1, P3) because of the long lever arm distance from the fixed points to the loading point. 5. Higher equivalent stresses were distributed throughout the metal base overdenture than the resin base overdenture under the same loading condition. 6. The case of occlusal third contact of the abutment to the denture produced higher equivalent stresses in the abutment, the mandibular area around the abutment and the overdenture than the case of a 1mm space between the denture and the abutment. 7. Without regard to overdenture base materials and designs, the amounts and distribution patterns of equivalent stresses under the same loading condition were similar in the mucous membrane.

• 대한의용생체공학회:의공학회지
• /
• 제19권5호
• /
• pp.503-511
• /
• 1998

본 연구에서는 동적충격하중 하에서 다양한 tibial component system의 하중전달현상 및 발생 가능한 실패기전을 관찰하기 위해 서로 다른 tibial component들에 대한 수치해석을 통한 응력분포를 관찰하고 또한 접합 상태에 따른 임플란트 시스템이 받는 영향을 비교 분석하였다. 따라서, 해석에 고려되는 모델은 정상 경골과 현재 가장 많이 적용되는 시스템인 시멘트형과 무시멘트형 metal-backed tibial component, 폴리에틸렌으로 된 시멘트형 tibial component, 그리고 골과 slew사이의 비접합상태를 가정한 metal-backed tibial component을 포함한다. 해석 결과 metal-backed tibial component의 stem 끝 부분에서는 시멘트형이 무시멘트형 보다 약간 더 놀은 최대 응력을 보였다. 반면, 폴리에틸렌으로 된 tibial component의 경우 stem 글 부분에서의 최대 응력은 metal-backed tibial component에 비해 차 반 정도로 줄었고, 전체적으로 정상 경골에 유사한 응답 특성을 보여주었다. 골과 stem 사이의 비접합을 가정한 경우 금속 tray 밑 부된에서의 응력은 완전히 접합된 경우 보다 3배 더 높았고, stem 끝부분에서는 시간에 따른 불안정한 응력이 관찰되어 이 현상은 임플란트 해리현상과 불완전한 골접합을 가중시키는 원인으로 사료된다. 따라서, 수직충격하중을 고려한 경우 골에 안정하게 고정되는 폴리에틸렌 tibial component가 가장 바람직하다.

• 한국환경과학회지
• /
• 제17권2호
• /
• pp.135-140
• /
• 2008

Steel net gabion is eco-friendly retaining wall structure showing favorable ability to overcome construction and environmental restriction and also to resist corrosion, chemical attack and degradation. This paper is dealt with the applicability of gabion metal net as a substitution of existing strengthening material. Pull out test was carried out to verify the applicability of gabion metal net. According to results, the increase of surcharge loading and horizontal load resulted in a yield of metal net. The stress at the time of yield was in the range of elasticity. Accordingly, gabion metal net can be substituted for existing geogrid and there is a need for experiment and analysis of arrangement direction and durability of gabion steel net.

• 한국전기전자재료학회논문지
• /
• 제25권8호
• /
• pp.632-638
• /
• 2012

The prepartion of various metal oxide nanostructures via hydrothermal method, hydrolysis, thermal evaporation and electrospinning and their applications to chemoresistive sensors have been investigated. Hierarchical and hollow nanostructures prepared by hydrothermal method and hydrolysis showed the high response and fast responding kinetics on account of their high gas accessibility. Thermal evaporation and electrospinning provide the facile routes to prepare catalyst-loaded oxide nanowires and nanofibers, respectively. The loading of noble metal and metal oxide catalyst were effective to achieve rapid response/recovery and selective gas detection.

• 대한기계학회논문집A
• /
• 제31권11호
• /
• pp.1124-1130
• /
• 2007

This paper presents a new way for fabricating sandwich plates with tetrahedral truss cores. The tetrahedral truss cores are manufactured through metal expanding and bending process and then brazed with solid face sheets. The properties of sandwich plates with the tetrahedral truss cores composed of a wrought steel SS41 under compression and shear loading have been investigated. Good agreement is observed between the measured and predicted peak strengths. Comparisons with normalized compressive strength for other cellular metals have indicated that the tetrahedral truss structures outperform aluminum open cell forms and woven core sandwich plates.

• 한국기계가공학회지
• /
• 제12권2호
• /
• pp.41-48
• /
• 2013

Springback is a very typical dimensional discrepancy phenomenon, which occurs usually on the final stamping parts after the tool loading is removed. Variation of springback leads to amplified variations and problems during assembly of the stamped components, in turn, resulting in quality issues. The variations in the properties of the incoming material and process parameters are the main causes of springback variation. In this research, a robust design methodology which combines orthogonal array based experimental design and design space reduction skim to reduce the springback variation for advanced high strength steel parts in sheet metal forming is suggested. The concept of design space reduction is adapted in the experimental design setup to improve the quality of the obtained solution. The effectiveness of the proposed procedures is illustrated through a robust design of springback in metal forming process of a cross member of auto body.

• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.677-687
• /
• 2016

On the basis of the energy approach it is reported a development of the yield function and the constitutive equations for the orthotropic material with consideration of the crystal lattice constants and parameters of the crystallographic texture for the general stress state. For practical use in sheet metal forming analysis it is considered different loading scenarios: plane stress and plane strain states. Using the proposed yield function, the influence of single ideal components on the shape of yield surface was analyzed. The six texture components investigated here were cube, Goss, copper, brass, S and rotated cube, as these components are typically observed in rolled sheets from FCC alloys.