• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.33-36
• /
• 2007

Currently, many structured catalysts using microchannel are researched to apply to fuel reforming. In this paper, ceramic monolith and metal mesh as structured catalysts are investigated for catalytic autothermal reforming. When GHSV increases, each structured catalyst has better performances(hydrogen production, fuel conversion) than packed bed catalyst for autothermal reforming. The major causes seem to be the elevated heat and mass transfer, gas phase reaction and redistribution of packed bed due to high pressure drop.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.203-206
• /
• 2009

Agglomeration of catalysts is known as one of the major degradation mechanisms. Reforming of liquid fuel, which requires high temperature over $800^{\circ}C$, accelerates agglomeration of catalysts. In this work, The effects of agglomeration on catalysts activity in partial oxidation reforming conditions were investigated. Metal supported catalysts(Pt-CGO, Ru-CGO) were compared to perovskite-structured catalysts(NECS-P1, NECS-P2). High thermal stability of perovskite-structured catalysts was reported. Micro-reactor installed in electric furnace was used. its Temperature was raised from $800^{\circ}C$ to $1000^{\circ}C$ to accelerate agglomeration effect. To measure rate of agglomeration, BET analysis and CO pulse chemisorption were conducted on catalysts exposed to $1100^{\circ}C$. Metal supported catalysts showed degradation at $1000^{\circ}C$ and The rates were different according to metal supported. On the other hand perovskite-structured catalysts showed no degradation at $1000^{\circ}C$.

• Clean Technology
• /
• v.24 no.2
• /
• pp.127-134
• /
• 2018

To reduce the environmental pollution by $NO_x$ from ship engine, International maritime organization (IMO) announced Tier III regulation, which is the emmision regulation of ship's exhaust gas in Emission control area (ECA). Selective catalytic reduction (SCR) process is the most commercial $De-NO_x$ system in order to meet the requirement of Tier III regulation. In generally, commercial ceramic honeycomb SCR catalyst has been installed in SCR reactor inside marine vessel engine. However, the ceramic honeycomb SCR catalyst has some serious issues such as low strength and easy destroution at high velocity of exhaust gas from the marine engine. For these reasons, we design to metallic structured catalyst in order to compensate the defects of the ceramic honeycomb catalyst for applying marine SCR system. Especially, metallic structured catalyst has many advantages such as robustness, compactness, lightness, and high thermal conductivity etc. In this study, in order to support catalyst on metal substrate, coating slurry is prepared by changing binder. we successfully fabricate the metallic structured catalyst with strong adhesion by coating, drying, and calcination process. And we carry out the SCR performance and durability such as sonication and dropping test for the prepared samples. The MFC01 shows above 95% of $NO_x$ conversion and much more robust and more stable compared to the commercial honeycomb catalyst. Based on the evaluation of characterization and performance test, we confirm that the proposed metallic structured catalyst in this study has high efficient and durability. Therefore, we suggest that the metallic structured catalyst may be a good alternative as a new type of SCR catalyst for marine SCR system.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.230.2-230.2
• /
• 2010

천연가스 수증기 개질 반응에 사용되는 펠릿 촉매의 단점인 열 및 물질 전달 제한, 낮은 effectiveness factor, 압력강화와 channeling 등의 문제점을 해결 하고자 모노리스 형태의 금속 구조체 촉매를 본 연구에 적용 하였다. Fecralloy 재질의 금속 구조체에 Ni 촉매를 워시코팅 (wash coating) 하여 제조 하였으며, 이를 천연가스 수증기 개질 반응에 적용하여 수소를 생산하였다. 실험 조건으로는 S/C ratio를 3으로 고정하여 온도를 $600^{\circ}C{\sim}800^{\circ}C$로 변화 시켰으며, GHSV $3000{\sim}30000h^{-1}$에서 진행 되었다. 구조체 촉매 코팅에 사용된 Ni 촉매의 BET, TPR, H2-chemisorption, SEM, EDS의 특성분석을 수행 하였다. 온도별 테스트에서 모노리스 형태의 금속 구조체 촉매가 펠릿 형태의 촉매에 비해 우수한 열전달 효과로 인해 낮은 퍼니스 온도와 높은 반응 활성을 나타내었으며, GHSV 변화에 따른 성능평가 결과도 15wt% $Ni/MgAl_2O_4$펠릿 촉매와 비교하여 금속 구조체 촉매가 높은 활성을 보였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.224.1-224.1
• /
• 2010

본 연구에서는 천연가스 수증기 개질반응에 니켈 촉매가 코팅된 금속 구조체 촉매를 적용하여 수소를 생산하였다. 금속구조체 촉매는 기존 펠릿 촉매가 충진 된 촉매반응기에 비해 열 및 물질 전달 특성이 우수하여 이를 여러 개질반응에 적용하고자하는 연구가 수행되어 왔다. 하지만, 기존 금속구조체 촉매의 개발에 있어 촉매와 금속 지지체간의 안정한 결합을 통한 열안정성 확보에 대한 문제는 여전히 해결과제로 남아 있다. 따라서, 본 연구에서는 니켈 촉매를 금속 지지체에 안정하게 부착하기 위한 금속 지지체 표면 처리 방법을 개발하였으며 금속 구조체의 형상에 상관없이 균일한 표면처리가 가능하였다. 개발된 표면 처리방법을 적용한 금속 구조체 촉매는 촉매와 금속지지체간의 결합력 향상으로 인해 120시간 이상 안정한 반응활성을 보였다. 또한, 빠른 공간속도에서도 펠릿촉매와 표면처리를 적용하지 않은 금속 구조체 촉매에 비해 높은 촉매 활성을 보였다. 뿐만 아니라, 본 연구에서 개발된 표면처리를 모노리스와 폼을 비롯한 다양한 형상의 금속구조체 촉매에 적용하여 기하학적 표면 특성에 따른 촉매의 활성 차이를 살펴보았다. 겉보기 표면적이 넓은 금속구조체일 수록 촉매의 고분산 코팅에 유리하여 높은 활성을 보였다.

• Applied Chemistry for Engineering
• /
• v.35 no.2
• /
• pp.134-139
• /
• 2024

In the steam reforming of methane reactions, the effect of adding noble metals Ru and Pd to a Ni-based catalyst as promoters was analyzed in terms of catalytic activity and hydrogen production. The synthesized catalysts were coated on the surface of a honeycomb-structured metal monolith to perform steam methane reforming reactions. The catalysts were characterized by XRD, TPR, and SEM, and after the reforming reaction, the gas composition was analyzed by GC to measure methane conversion, hydrogen yield, and CO selectivity. The addition of 0.5 wt% Ru improved the reduction properties of the Ni catalyst and exhibited enhanced catalytic activity with a methane conversion of 99.91%. In addition, reaction characteristics were analyzed according to various process conditions. Methane conversion of over 90% and hydrogen yield of more than 3.3 were achieved at a reaction temperature of 800 ℃, a gas hourly space velocity (GHSV) of less than 10000 h^-1, and a ratio of H₂O to CH₄ (S/C) higher than 3.

• Journal of Powder Materials
• /
• v.12 no.2 s.49
• /
• pp.117-121
• /
• 2005

Platinum catalysts for the DMFC (Direct Methanol Fuel Cell) were impregnated on several carbon supports and their catalytic activities were evaluated with cyclic voltammograms of methanol electro-oxidation. To increase the activities of the Pt/C catalyst, carbon supports with high electric conductivity such as mesoporous carbon, carbon nanofiber, and carbon nanotube were employed. The Pt/e-CNF (etched carbon nanofiber) catalyst showed higher maximum current density of $70 mA cm^{-2}$ and lower on-set voltage of 0.54 V vs. NHE than the Pt/Vulcan XC-72 in methanol oxidation. Although the carbon named by CNT (carbon nanotube) series turned out to have larger BET surface area than the carbon named by CNF (carbon nanofiber) series, the Pt catalysts supported on the CNT series were less active than those on the CNF series due to their lower electric conductivity and lower availability of pores for Pt loading. Considering that the BET surface area and electric conductivity of the e-CNF were similar to those of the Vulcan XC-72, smaller Pt particle size of the Pt/e-CNF catalyst and stronger metal-support interaction were believed to be the main reason for its higher catalytic activity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.86-86
• /
• 2012

The new approaches for silicon solar cell of new concept have been actively conducted. Especially, solar cells with wire array structured radial p-n junctions has attracted considerable attention due to the unique advantages of orthogonalizing the direction of light absorption and charge separation while allowing for improved light scattering and trapping. One-dimenstional semiconductor nano/micro structures should be fabricated for radial p-n junction solar cell. Most of silicon wire and/or pillar arrays have been fabricated by vapour-liquid-solid (VLS) growth because of its simple and cheap process. In the case of the VLS method has some weak points, that is, the incorporation of heavy metal catalysts into the growing silicon wire, the high temperature procedure. We have tried new approaches; one is electrochemical etching, the other is noble metal catalytic etching method to overcome those problems. In this talk, the silicon pillar formation will be characterized by investigating the parameters of the electrochemical etching process such as HF concentration ratio of electrolyte, current density, back contact material, temperature of the solution, and large pre-pattern size and pitch. In the noble metal catalytic etching processes, the effect of solution composition and thickness of metal catalyst on the etching rate and morphologies of silicon was investigated. Finally, radial p-n junction wire arrays were fabricated by spin on doping (phosphor), starting from chemical etched p-Si wire arrays. In/Ga eutectic metal was used for contact metal. The energy conversion efficiency of radial p-n junction solar cell is discussed.

• Nuclear Engineering and Technology
• /
• v.44 no.1
• /
• pp.9-20
• /
• 2012

A brief review on the thermal plasma synthesis of nano-sized powders is presented according to the application materials, such as, metals, ceramics, glasses, carbonaceous materials and other functional composites, such as, supported metal catalyst and core-shell structured nano materials. As widely adopted plasma sources available for thermal plasma synthesis of nanosized powders, three kinds of plasma torches, such as transferred and non-transferred DC and RF plasma torches, are introduced with the main features of each torch system. In the basis of the described torch features and the properties of suggested materials, application results including synthesis mechanism are reviewed in this paper.

• Clean Technology
• /
• v.30 no.1
• /
• pp.55-61
• /
• 2024

Efforts are actively underway to address the issues related to the high cost of Pt-based catalysts for oxygen reduction reactions by designing high-performance Pt-based alloys through the control of their nanostructures. In this study, a method was proposed to control the nanostructure of Pt-based alloys, either hollow or core-shell, by adjusting the pH of the solution during the galvanic replacement reaction between the carbon-supported nickel-nickel nitride composite and the Pt ions. The physical characteristics, including the state, quantity, and morphology of the metal particles under different preparation conditions, were evaluated through X-ray diffraction, transmission electron microscopy, and inductively coupled plasma. When the prepared catalysts were employed for the oxygen reduction reaction, they exhibited an improvement in area specific-activity compared to a commercial Pt/C, with a 1.7 and 1.9-fold enhancement for the hollow and core-shell structured catalysts, respectively.