• Korean Journal of Optics and Photonics
• /
• v.21 no.1
• /
• pp.21-25
• /
• 2010

In this paper, in order to enhance the image reconstruction performance of white light scanning interferometry(WLI), we demonstrate the scattered point noise filtering performance of post-processing methods. Median filtering is similar to using an averaging filter. Because the median value is less sensitive than the mean to extreme values, the median filter can remove the scattered point noise from a height-map without significantly reducing the sharpness of the image. In several specific cases, however, the median filter can't remove the scattered point noise. Therefore, we propose a comparative mean filter that uses order-statistic filtering and the mean of the neighborhood pixels. The performance is demonstrated by measuring an array of metal solder balls fabricated on PCB. The proposed method reduced the noise pixels by 4.4 percent.

• Korean Journal of Soil Science and Fertilizer
• /
• v.14 no.4
• /
• pp.242-249
• /
• 1982

Effects of lime and ameliolating materials on decreasing available soil cadmium were studied, applying the amendments to Cd pre-and post-treated soils. Soil sttreated with Cd were placed in pots and kept under field moisture condition, summer through winter in 1981. The results of soil analysis made 40 to 60 days after the Cd treatment are as follows ; 1. Greater amount of Cd was extracted by 0.1N-HCl or 2% Citric acid than N-AcNH4 solution. More Cd was dissoluted by 0.1-HCl than 2% Citric acid. No Cd was extracted by pure water. Showing a wide variance in the amount of extractable Cd among treatments (amendments), the $N-AcNH_4$ solution seemed to be the most effective extracting solution of available soil cadmium. 2. Calcium hydroxide was the most effective materials in reducing $N-AcNH_4$ extractable Cd, followed by calcium carbonate and calcium silicate. 3. Superphosphate is also effective in reducing exchangeable cadmium. The reduction seemed to be attributed to the precipitation of cadmium phosphate. 4. The exchangeable cadmium by $N-AcNH_4$ was large in the soil pH range of 6.0 and 6.5, and it decreased as the soil pH became far apart from these values. The decrese of exchangeable Cd at low pH seemed to be related to the increase of $Mn^{+{+}}$ and that at the high pH to the precipitation as Cd-hydroxide.

• Journal of the Korean Ceramic Society
• /
• v.39 no.12
• /
• pp.1128-1132
• /
• 2002

$ReMnO_3$(Re:Y, Ho, Er) thin films were prepared by MOCVD method available to non-volatile memory device with MFS-FET structure. $ReMnO_3$ thin films were deposited on the Si(100) substrate at 700${\circ}C$ for 2h. When the films were post-annealed at 900${\circ}C$ for 1h in air, the single phase of hexagonal $ReMnO_3$ thin films were detected. Ferroelectric properties of $ReMnO_3$ thin films were dependent on the degree of c-axis orientation in the single phase of hexagonal structure and remnant polarization (Pr) of $YMnO_3$ thin films with high degree of c-axis orientation was 105 nC/$cm^2$. Leakage current density was dependent on the grain size of microstructure and that of $YMnO_3$ thin films with grain size of 100∼150 nm was $10^{-8}$ A/$cm^2$ at applied voltage of 0.5 V.

• IMMUNE NETWORK
• /
• v.6 no.2
• /
• pp.86-92
• /
• 2006

Background: Germanium compounds are increased to use in nutrient foods and medicines in terms of antibiotics to microbes, anticancer, modulation of immune system and neutralizing heavy metal toxins. Geranti Bio-Ge Yeast, containing stable organic germanium and bound to the yeast protein was developed by Geranti Pharm. LTD. and the modulation effect in the immune system was examined in vivo and in vitro. Methods: The compound, Geranti Bio-Ge Yeast, was fed to female Balb/c mice (each group has 10 mice) for 4 weeks and the yeast powder and steamed red ginseng powder were used as control during the same feeding time points. During 4 weeks there was no symptom to be considered, and after 4 weeks feeding all mice were sacrificed to check the changes of related immune cells and subsidiary responses (i.e. cell counting, FACS, MTT, LDH, PFC assay). Results: In pre-post comparison, B cell population was increased in the group of Geranti Bio-Ge Yeast in a dose dependent manner (100 to 800 mg/kg). However, the population of T cell, dendritic cell and macrophage was not comparably changed in all doses. The ability of cytokine production and proliferation was almost same level as shown in control group. In contrast, PFC assay informed that the compound increase the antibody production ability when fed over 200 mg/kg implying that the increase of PFC number might be due to the increase of B cells. Conclusion: Over the entire study, we concluded that the compound, Geranti Bio-Ge Yeast has better potential in immune response in terms of B cell proliferation than that of positive control, red ginseng, and the compound can be one of the future candidates for a new supplementary source improving immune system activity.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.2
• /
• pp.49-53
• /
• 2017

We study on the change of electrical properties of two-dimensional (2D) $SnSe_2$ materials with respect to Cl doping as $SnSe_{1.994}Cl_{0.006}$ under a high temperature condition. (300~450 K) By the simple solid-state reaction method, non-and Cl-doped 2D $SnSe_2$ materials are successfully synthesized with negligible impurities as confirmed by X-ray diffraction. From the temperature dependence of resistivity, it is observed that the conduction mechanism is changed from hopping to degenerate conduction with Cl doping. By Hall effect measurement, an increase on electron carrier concentration from ${\sim}7{\times}10^{16}$ to ${\sim}3{\times}10^{18}cm^{-3}$ with Cl doping verifies that Cl is an effective electron donor which results in the encouraged carrier concentration. Detailed analysis for temperature dependent Hall mobility reveals that the electrical transports in high temperature regime are governed by the grain boundary-controlled mechanism for non-doped $SnSe_2$, which is effectively suppressed by Cl-doping as entering metallic transport regime.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.21-27
• /
• 2016

Global warming due to greenhouse gas emissions is considered as a major problem worldwide, and many countries are making great efforts to reduce carbon dioxide emissions. Many technologies in post-combustion, pre-combustion and oxy-fuel combustion $CO_2$ capture have been developed. Among them, a hybrid pre-combustion $CO_2$ capture system of a water gas shift (WGS) reactor and a membrane gas separation unit was investigated. The 2 stage WGS reactor integrated high temperature shift (HTS) with a low temperature shift (LTS) was used to obtain a higher CO conversion rate. A Pd/Cu dense metal membrane was used to separate $H_2$ from $CO_2$ selectively. The performance of the hybrid system in terms of CO conversion and $H_2$ separation was evaluated using a 65% CO, 30 % $H_2$ and 5% $CO_2$ gas mixture for applications to pre-combustion $CO_2$ capture. The experiments were carried out over the range of WGS temperatures ($200-400^{\circ}C$), WGS pressures (0-20bar), Steam/Carbon (S/C) ratios (2.5-5) in a feed gas flow rate of 1 L/min. A very high CO conversion rate of 99.5% was achieved with the HTS-LTS 2 stage water gas shift reactor, and 83% $CO_2$ was concentrated in the retentate using the Pd/Cu membrane.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.3736-3741
• /
• 2015

Crash impact test is conducted to verify the crashworthiness of fuel tank. Success of the crash impact test means the improvement of survivability of crews by preventing post-crash fire. But, there is a big risk of failure due to huge external load in the crash impact test. The failure of crash impact test can result in serious delay of a entire rotorcraft development because of the design complement and re-production of the test specimens requiring a long-term preparation. Thus, the numerical simulations of the crash impact test has been required at the early design stage to minimize the possibility of trial-and-error in the real test. Present study conducts on the numerical simulation of phase I crash impact test using SPH supported by crash simulation software, LS-DYNA. Test condition of MIL-DTL-27422 is reflected on analysis and material data is acquired by specimen test of fuel cell material. As a result, the crash load on the skin material, overlap area and metal fitting is estimated to confirm the possibility of acquisition of the design load for the determination of the overlap area and adhesive strength.

• Journal of Powder Materials
• /
• v.29 no.5
• /
• pp.411-417
• /
• 2022

Environmental issues such as global warming due to fossil fuel use are now major worldwide concerns, and interest in renewable and clean energy is growing. Of the various types of renewable energy, green hydrogen energy has recently attracted attention because of its eco-friendly and high-energy density. Electrochemical water splitting is considered a pollution-free means of producing clean hydrogen and oxygen and in large quantities. The development of non-noble electrocatalysts with low cost and high performance in water splitting has also attracted considerable attention. In this study, we successfully synthesized a NiCo₂O₄/NF electrode for an oxygen evolution reaction in alkaline water splitting using a hydrothermal method, which was followed by post-heat treatment. The effects of heat treatment on the electrochemical performance of the electrodes were evaluated under different heat-treatment conditions. The optimized NCO/NF-300 electrode showed an overpotential of 416 mV at a high current density of 50 mA/cm² and a low Tafel slope (49.06 mV dec^-1). It also showed excellent stability (due to the large surface area) and the lowest charge transfer resistance (12.59 Ω). The results suggested that our noble-metal free electrodes have great potential for use in developing alkaline electrolysis systems.

• Journal of the Microelectronics and Packaging Society
• /
• v.31 no.3
• /
• pp.18-23
• /
• 2024

Nanoimprint lithography (NIL) is widely used to form structures ranging from micro to nanoscale due to its advantage of generating high-resolution patterns at a low process cost. However, most NIL processes require the use of imprint resists and external elements such as ultraviolet light or heat, necessitating additional post-processes like etching or metal deposition to pattern the target material. Furthermore, patterning on flexible and/or non-planar films presents significant challenges. This study introduces an extreme pressure imprint lithography (EPIL) process that can form micro-/nano-scale patterns on the surface of a flexible rubber magnet composite (RMC) film at room temperature without an etching process. The EPIL technique can form ultrafine structures over large areas through the plastic deformation of various materials, including metals, polymers, and ceramics. In this study, we demonstrate the process and outcomes of creating a variety of periodic structures with diverse pattern sizes and shapes on the surface of a flexible RMC composed of strontium ferrite and chlorinated polyethylene. The EPIL process, which allows for the precise patterning on the surface of RMC materials, is expected to find broad applications in the production of advanced electromagnetic device components that require fine control and changes in magnetic orientation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.599-604
• /
• 1998

We have investigated Pt and $RuO_2$ as a bottom electrode for ferroelectric capacitor applications. The bottom electrodes were prepared by using an RF magnetron sputtering method. Some of the investigated parameters were a substrate temperature, gas flow rate, RF power for the film growth, and post annealing effect. The substrate temperature strongly influenced the surface morphology and resistivity of the bottom electrodes as well as the film crystallographic structure. XRD results on Pt films showed a mixed phase of (111) and (200) peak for the substrate temperature ranged from RT to $200^{\circ}C$, and a preferred (111) orientation for $300^{\circ}C$. From the XRD and AFM results, we recommend the substrate temperature of $300^{\circ}C$ and RF power 80W for the Pt bottom electrode growth. With the variation of an oxygen partial pressure from 0 to 50%, we learned that only Ru metal was grown with 0~5% of $O_2$ gas, mixed phase of Ru and $RuO_2$ for $O_ 2$ partial pressure between 10~40%, and a pure $RuO_2$ phase with $O_2$ partial pressure of 50%. This result indicates that a double layer of $RuO_2/Ru$ can be grown in a process with the modulation of gas flow rate. Double layer structure is expected to reduce the fatigue problem while keeping a low electrical resistivity. As post anneal temperature was increased from RT to $700^{\circ}C$, the resistivity of Pt and $RuO_2$ was decreased linearly. This paper presents the optimized process conditions of the bottom electrodes for memory device applications.