• Journal of Welding and Joining
• /
• v.24 no.4
• /
• pp.15-21
• /
• 2006

The aim of present study is to investigate the effect of welding parameters and heat treatment conditions on the formability of the $CO_2$ laser welded silicon steel sheet. It was found that there is optimum range of the heat input ($0.6{\sim}0.7kJ/cm$) and gap distance ($0.125{\sim}0.150mm$) for the high tensile strength and the avoidance of the fracture in weld metal. Also, it was essential fur the improvement of formability to perform pre- and post-welding heat treatment which cause the uniform mixture of base metal and welding consumable.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.121-123
• /
• 2006

The aim of present study is to investigate the effect of welding parameters and heat treatment conditions on the formability of the laser welded silicon steel sheet. It was found that there is optimum range of the heat input ($0.6{\sim}0.7kJ/cm$) and gap distance ($0.125{\sim}0.150mm$) for the high tensile strength and the avoidance of the fracture in weld metal, Also, it was essential for the improvement of formability to perform pre- and post-welding heat treatment which cause the uniform mixture of base metal and welding consumable.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.3 s.116
• /
• pp.23-28
• /
• 2006

Xylan in hemicellulose has been reported as one of the reasons of the yellowing of chemical pulp and paper. But little relevant information is available in literature. In this study, we examined into the influence that glucuronoxylan or glucomannan and metallic ion($Cu^{2+},\;Fe^{2+},\;Fe^{3+},\;Mn^{2+}$) residued in pulp get each or when mixed at yellowing. Filter paper was treated with each metallic ion, glucuronoxylan and the mixture of glucuronoxylan and metal ions, and brightness and CIE $L^*a^*b^*$ was measured after accelerated aging. As the results of measurements, the filter paper processed by 10% glucuronoxylan was dropped $2{\sim}3%$ on the brightness after accelerated aging for 24 hours. Also, the filter paper treated with glucuronoxylan and $Fe^{2+}$ was dropped 7% on the brightness.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.118.2-118.2
• /
• 2017

Combustion behavior of Fe, CuO, NiO, ZnO and $Fe_2O_3$ powder mixture was carried out by finite element method (FEM) to understand a reaction at iron and metal oxide interface. The FEM was done by using ANSYS Fluent 17.0. Initial and boundary conditions are 1 atmosphere, room temperature, 0.1MPa of oxygen partial pressure, $T_{S1}=1127^{\circ}C$, $T_{S2}=327^{\circ}C$ for a cylindrical shape specimen with dia. $35{\times}80$ [mm]. The maximum combustion temperature is $1537^{\circ}C$ for the condition of conduction, convection and radiation. The combustion temperature and rate are about $847^{\circ}C$ and 3.9mm/sec, respectively. The combustion wave is enough to make ternary ferrite phase like $CuNiZnFe_2O_3$.

• Journal of Welding and Joining
• /
• v.11 no.1
• /
• pp.73-79
• /
• 1993

The phenomenon of metal transfer has been investigated for different transfer modes using a digital high speed motion analyzer and an arc shadow-graphing system based on a laser source and related optical system. It was observed that the pinch instability phenomenon did not occur for the globular transfer mode, since the liquid globule was then spherical rateher than a cylindrical liquid bar. On increasing the ratio of carbon dioxide to argon, the transition current from globular to spray transfer generally increased, but it is interesting that the transition was observed to occur at the lowest current in a 5% CO$_{2}$-95% argon gas mixture. For pure carbon dioxide and helium shielding gases, the drop frequency increased slowly with increasing current. At high currents or an argon based shielding gas, the length of liquid bar decreased as the carbon dioxide content increased. The acceleration of a droplet within the arc was determined using the gas drag force theory and was found to be greater than the experimental results.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.38-45
• /
• 1999

Shielding gas has significant effects on arc stability, metal transfer and weld quality in the gas metal arc welding (GMAW) process. The double gas-shielded MAG(DMAG) and auxiliary gas-shielded MAG (AMAG) torches are investigated for their capability to provide argon-rich gas mixture using small amount of argon gas through the inner and auxiliary nozzles, respectively. Argon composition with the DMAG torch is calculated numerically, and compared with the measured data using the gas chromatogrphy. Gas flow pattern of the DMAG torch is calculated to change from the laminar to turbulent flow when total gas flow rate becomes larger than 4.5 liter/min at room temperature. While argon-rich shielding gas was obtained using both the AMAG and DMAG torches, the AMAG torch provides higher argon composition than the DMAG torch, which demonstrates that argon gas can be utilized more efficiently with the AMAG torch.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.9
• /
• pp.883-887
• /
• 2006

In order to attain high-rate deposition of Mn-Zn ferrite thin film for soft magnetic underlayer in perpendicular magnetic recording media, a reactive sputtering using powder-metal targets under the mixture gas of Ar and $O_{2}$ was performed. It was succeeded that Mn-Zn ferrite films with (111) crystal orientation were deposited on Pt(111) underlayer without any annealing process. The film revealed 3.4 kG of 4 ${\pi}Ms$, 70 Oe of coercivity. The deposition rate of the new method was 16 times as high as that of the conventional method using ferrite target.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.6
• /
• pp.930-934
• /
• 2005

A chloroform membrane system containing a given mixture of benzylaza-12-crown-4 and oleic acid is introduced for the selective and efficient transport of $Pb^{2+}$ ion. The transport was capable of moving metal ions ‘up-hill’. In the presence of ${S_2O_3}^{2-}$ion as a suitable metal ion acceptor in the receiving phase, the amount of lead ion transport across the liquid membrane after 150 minutes is (95.0 ${\pm}$ 1.7)%. The selectivity and efficiency of lead transport from aqueous solution containing $Tl^+,\;Ag^+,\;Mg^{2+},\;Ca^{2+},\;Co^{2+},$ $Ni^{2+},\;Cu^{2+},\;Zn^{2+},\;Hg^{2+}$ and $Cd^{2+}$were investigated. In the presence of thiosulfate as a suitable masking agent in the source phase, the interfering effects of $Ag^+\;and\;Cu^{2+}$ were diminished drastically.

• Journal of the Korean Ceramic Society
• /
• v.43 no.11 s.294
• /
• pp.703-709
• /
• 2006

We report on the synthesis of highly uniform, single phase zinc and cobalt thin films prepared by the Liquid Phase Deposition (LPD) method. X-Ray diffraction, TGA and EDX measurements support the assumption that the as deposited films are constituted by a mixture of crystallized FeOOH and amorphous M(OH)$_2$ (M=Co, Zn) which is converted upon heat treatment in air at 600?C into the corresponding zinc ferrites. The films with adjustable chemical compositions are identified with a crystal structure as spinel-type and present a spherical or rod-like microstructure, depending on the both the nature and concentration of the divalent transition metal ions. Zinc ferrite thin films present a superparamagnetic behavior above blocking temperatures which decrease with increasing the Zn content and are ferromagnetic at 5 K with coercivities ranging between 797.8 and 948.5 Oe, whereas the cobalt ferrite films are ferromagnetic at room temperature with magnetic characteristics strongly dependent on the chemical composition.

• Journal of Powder Materials
• /
• v.10 no.4
• /
• pp.288-293
• /
• 2003

Mechanical alloying (MA) by high energy ball mill of Pure chromium Powders was carried out under the nitrogen gas atmosphere. Cr-N amorphous alloy powders have been produced through the solid-gas reaction subjected to MA. The atomic structure during amorphization process was observed by X-ray and neutron diffractions. An advantage of the neutron diffraction technique allows us to observe the local atomic structure surrounding a nitrogen atom. The coordination number of metal atoms around a N atom turns out to be 5.5 atoms. This implies that a nitrogen atom is located at both of centers of the tetrahedron and octahedron formed by metal atoms to stabilize an amorphous Cr-N structure. Also, we have revealed that a Cr-N amorphous alloy may produced from a mixture of pure Cr and Cr nitrides powders by solid-solid reaction during mechanical alloying.