• Resources Recycling
• /
• v.25 no.5
• /
• pp.3-13
• /
• 2016

Statistics on the urban mining industry is the essential information to develop the urban mining industry systematically and the prerequisite way to understand its related trends. Status on domestic urban mining industry was thus investigated through the integrated method which uses both the top-down way based on the national statistics utilization and the bottom-up way based on field data gathering. Results indicated that the scale of metal resources produced through domestic urban mine was 19.6 trillion won, which corresponds to approximately 22 percent of metal demand in korea. The number of firms for urban mining was 917, and they are mostly placed in metropolitan area and Gyeongsang province. It was also found that about 58 percent of urban mining firms was in small business level less than 10 employees. Compared to the results in 2009, the number of urban mining companies in 2014 generally increased, and that of rare metal companies grew up significantly. This study is particularly different from the conventional statistics investigation on the point of the actual scale findings of metal resources based on the field data.

• Resources Recycling
• /
• v.22 no.3
• /
• pp.91-99
• /
• 2013

Steel industry which has been accomplishes the base of our country economy, automobile and electronic industry are taking charge of the role, whose electroplating is important. Large amount of wastewater and various metal salts, including hazardous materials was generated from the electroplating pre-treatment, plating, washing and post-plating. Currently, the general wastewater follows in the environmental law and neutralization after controlling, sludge where the various metal is mixed reclaims below multiple regulative and trust it is controlling. The sludge which includes the gas price metal reclaims in the field and trust it controls. a reclamation price of land it is insufficient but and the control expense holds plentifully and it loses the gas price metal which is valuable. Consequently, The research regarding to recover a gas price metal actively from this waste water, it is advanced. A new method to recover valuable metals from electroplating wastewater synthesis of metal sulfides using topical methods utilizing iron oxidizing bacteria, reagent of sulfides and solvent extraction using an organic solvent, such as the development of the law to recover these metals and metal sulfides of wastewater using selective recovery have been studied. By using these wastewater treatment method under frequency above 95%, it has been obtained the valuable metal from the wastewater, where the metal ion of Fe, Cu, Zn and Ni complexes was mixed. As we discuss the wastewater, which has been discharged from electroplating process, it is important and will be applied to the resources of metal in the urban mine.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.2
• /
• pp.55-63
• /
• 2009

This study was performed to evaluate the heavy metal contents in various packaging board. Domestic and foreign OCC (old corrugated containers) and old duplex boards were used as raw materials. Tests were made for the printed and unprinted parts of the sample. Heavy metal contents of old food packaging boards made from virgin pulp fibers were also evaluated. The contents of heavy metals including lead (Pb), cadmium (Cd), barium (Ba), arsenic (As), antimony (Sb), selenium (Se), and mercury (Hg) were determined using ICP-AES (Inductively Coupled Plasma - Atomic Emission Spectrometer), and CV-AAS (Cold vapor-atomic absorption spectrometer) after digesting the samples in a microwave oven. The contents of heavy metals contained in domestic packaging board were higher than those in overseas samples, and OCC showed higher contents of heavy metals than old duplex boards. Printed parts gave greater heavy metal contents than unprinted parts. Results indicate that recycling of paper and paperboard products increases the heavy metal contamination of the paper packaging products and this derives mostly from the heavy metals contained in printing inks. Recycling processes that decrease heavy metals in recycled fibers and new printing inks that contains less heavy metals should be developed to solve the problem associated with the heavy metals in packaging paper products.

• Journal of Welding and Joining
• /
• v.26 no.4
• /
• pp.79-84
• /
• 2008

Use of sheet metal structure is increased in various fields such as automobile, aerospace and communication equipment industry. When this structure is welded, welding distortion is generated due to the non-uniformity of temperature distribution. Recently welding distortion becomes a matter of great importance in the structure manufacture industry because it deteriorates the product's quality by bringing about shape error. Accordingly many studies for solving the problems by controlling the welding distortion are being performed. However, it is difficult to remove all kinds of distortion by welding process, though various kinds of methods for reducing distortion are applied to production. Consequently, straightening process is operated if the high precision quality is requested after welding. The local heating method induces compression plastic deformation by thermal expansion in the heating stage and then leaves constriction of length direction in the cooling stage. Accordingly, in the case of sheet metal structure, straightening effect is expected by heating for the part of distortion. This study includes numerical analysis of straightening effect by the local heating method in distortion comes from production of welded sheet metal structure. Particularly straightening effect followed by dimensions of heating area is analyzed according to the numerical analysis. The numerical analysis is performed by constructing 3-dimensional finite element model for 0.4mm stainless steel-sheet metal. Results of this study confirm that straightening effect changes as heating area increases and the optimum value of heating area that proves the maximum straightening effect exists.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.2
• /
• pp.249-264
• /
• 1996

This study was conducted for the purpose of obtaining the fundamental data on improvement of working environment and contributing to health improvement of workers who dealed with metal by assessing the metal concentration in air of industries located in Chang-Won Industrial Complex. Authors measured the concentration of metals(Al, Cd, Cr, Cu, Mn, Ni, Pb, Sn and Zn) is the air to 25 working processes of 73 industries by flame atomic absorption spectrometry from February to December 1994. Personal air sampler was used for air sampling with mixed cellulose-ester membrane filter. The results were as follows : 1. The geometric means(range) of metal concentration; 1) Al: $0.1505mg/m^3$ ($0.0147-18.6100mg/m^3$) 2) Cd: $0.0077mg/m^3$ ($0.0003-7.0710mg/m^3$) 3) Cr: $0.0163mg/m^3$ ($0.0013-1.1510mg/m^3$) 4) Cu: $0.0097mg/m^3$ ($0.0009-0.4950mg/m^3$) 5) Mn: $0.0412mg/m^3$ ($0.0006-4.7877mg/m^3$) 6) Ni: $0.0088mg/m^3$ ($0.0001-1.0170mg/m^3$) 7) Pb: $0.0152mg/m^3$ ($0.0015-0.4499mg/m^3$) 8) Sn: $0.0486mg/m^3$ ($0.0037-0.1500mg/m^3$) 9) Zn: $0.1911mg/m^3$ ($0.0122-8.2920mg/m^3$) 2. The geometric mean of lead exceeded TWA in assembling process of other general purpose machinery not elsewhere classified products manufacturing industries.

• Journal of Korean Institute of Industrial Engineers
• /
• v.42 no.6
• /
• pp.395-403
• /
• 2016

In mobile industry, using a metal frame of devices is rapidly increased for thin and stylish designs. However, fabricating metal is one of the difficult processes because the sophisticated control of equipment is required during the whole machining time. In this study, we present an efficient multivariate monitoring procedure for the metal frame process in mobile device manufacturing. The effectiveness of the proposed procedure is demonstrated by real data from the mobile plant in one of the leading mobile companies in South Korea.

• Journal of Integrative Natural Science
• /
• v.6 no.3
• /
• pp.151-157
• /
• 2013

The ion exchange resins were synthesized from 1-aza-18-crown-6 macrocyclic ligand attached to styrene (2th petroleum in 4th class hazardous material) divinylbenzene (DVB) copolymer with crosslinks of 1%, 6%, and 15% by substitution reaction. These synthetic resins were confirmed by chlorine content, elementary analysis, surface area, and IR-spectrum. The object of this study was to seperate the metal ion absorbed in reinforcement water fire extinguishing agent. As the results of the effects of pH, equilibrium arrival time, and crosslink of synthetic resin on metal ion adsorption for resin adsorbent, the metal ions were showed high adsorption at pH 3 or over and adsorption equilibrium of metal ions was about 2 hours. In addition, adsorption selectivity for the resin in water was the order of Al (III) > Ni (II) > Sm (III) ions, adsorbability of the metal ions was in the crosslinks order of 1%, 6%, and 15%.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.34-39
• /
• 2001

Following the trends around the world in the 1990's, Australia has been promoting recycling as a means to reduce wastes and at the same time improve the economics of metal processing. Of significance to the metal processing industry is the recycling of steel and aluminium, mostly from cans collected from households. The recycling of cyanide during gold processing has also been evaluated extensively, involving many R&D activities currently conducted in several laboratories and commercial plants in Australia. This paper presents an overview of the above issues, evaluating facts and data collected on metal recycling. The technologies currently developed and evaluated for cyanide recycling are also discussed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.2
• /
• pp.282-287
• /
• 2010

This paper gives a description of an experimental study of the ultrasonic welding of metals. In ultrasonic metal welding, high frequency vibrations are combined with pressure to join two materials together quickly and securely, without producing significant amount of heat. Ultrasonic metal welder consists of Transducer, Booster, and horn that are designed very accurately to get the natural frequencies and vibration mode. In this study, The horn was designed and analyzed the natural frequency by the modal analysis and harmonic analysis. And using a fiber optic sensor, we measured the amplitude and analyzed the Fast Fourier Transformed result. Using the horn, Ultrasonic metal welding between Cu sheet and Cu sheet of 0.1mm thickness was accomplished under the optimal conditions of static pressure 0.15MPa, vibration amplitude 30% and welding time of 0.28s. This result can be used for ultrasonic metal welding in manufacturing industry.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.4
• /
• pp.379-384
• /
• 2005

In general, water treatment sludge (WTS) had high concentration of heavy metal, thus it made the reuse or recycling of WTS difficult. The optimal solidification conditions for maximum suppression of heavy metal elution from WTS were decided in this study. Under the optimal solidification conditions (i.e., temperature, $320^{\circ}C;$ ratio of WTS and MgO, 9:1; solidification time, 1hr), all of heavy metal including aluminum were not detected. Therefore there are no problems for reuse or recycling of WTS which was solidified under the optimal solidification conditions found in the study.