• Journal of Welding and Joining
• /
• 제34권5호
• /
• pp.70-76
• /
• 2016

In this study, Microstructure and tensile properties in arc brazed joints of 1000MPa grade DP steel using Cu-Si insert metal were investigated. The fusion zone was composed of Cu phase which solidified a little Fe and Si. The former phase formed due to dilute the edge of base material by arc, although Fe was not solid solution in Cu at the room temperature. Cu3Si particles formed by crystallization at $1100^{\circ}C$ during faster cooling. After the tensile shear test, there are no differences between the brazed joint efficiencies. The maximum joint efficient was about 37% compared to strength of base metal. It is better than that of arc brazed joint of DP steel using Cu-Sn filler metal. Fracture position of all brazing conditions was in the fusion zone. Crack initiation occurred at three junction point which was a stress singularity point of upper sheet, lower sheet and the fusion zone. And then crack propagated across the fusion zone. The reason why the fracture occurred at fusion zone was that the hardness of fusion zone was lower than that of base material and heat affected zone. The correlation among maximum load and hardness of fusion zone and EST at fractured position was $R^2=0.9338$. Therefore, this means that hardness and EST can have great impact on maximum load.

• 한국환경농학회지
• /
• 제13권3호
• /
• pp.241-250
• /
• 1994

아연광산 인근지역의 농경지에 중금속의 오염정도와 옥수수의 생육에 미치는 영향을 조사하여 농작물 피해경감 대책의 기초자료로 활용하기 위하여 1993년에 경상북도 영양군 일월면 용화리 아연광산 수계지역의 토양중 중금속함량과 옥수수의 생육상황 및 토양중 중금속 함량과 식물체내 함량과의 관계에 대하여 조사 분석한 결과를 요약하면 다음과 같다. 1. 영양지역의 토양중 중금속 함량은 비오염지역인 칠곡에 비해 Zn, Cu, Pb,Cd, As 함량이 현저히 높았고 광산으로부터 거리별 토양중 중금속함량은 $2.0{\sim}2.5km$ 에서 가장 높았으나 3.0km 지점에서도 1.5Km 지점보다 높은 경향이었다. 2. 오염지역의 작물별 엽내 중금속 함량은 Zn, Cu, Pb, Cd, As 함량이 모두 콩에서 가장 높았고 다음은 옥수수, 벼의 순이었다. 3. 오염지역에서 옥수수 생육은 현저히 불량 하였고 토양중 중금속 함량도 월등히 많았다. 4. 옥수수의 부위별 중금속 함량은 토양중 함량과 같은 경향이었고 부위별로는 잎에서 가장 많았으며 원소별로는 Zn > Cu > As > Cd > Pb 순위이었으나, 각원소의 부위별 함량은 다소 차이가 있었다. 5. 토양중의 중금속함량과 옥수수 생육상황과는 전반적으로 부의 상관관계가 있었으나 조사된 원소중 Cu, Pb 함량과 옥수수의 초장, 착수고, 줄기굵기, 자수길이 및 수량과는 유의한 부의상관이 인정되었다. 6. 토양중 중금속 함량과 식물체 부위별 중금속 함량과의 관계는 대체로 정의 상관 관계를 나타냈으며, 토양중의 Pb, Cd, As 함량이 많으면 식물체 내의 Pb, Cd, As 함량이 증가되었고, 곡실중의 Pb와 As 함량은 토양중의 Cd 및 As와 유의한 정의 상관이 인정되었다.

• Journal of Welding and Joining
• /
• 제30권2호
• /
• pp.76-80
• /
• 2012

In this study, the effect of the welding current on the hardness characteristics and microstructure in the resistance spot welding of 1GPa grade cold-rolled DP steel was investigated, Also, correlation between the hardness and microstructure was discussed. In spite of the change in the welding current, the hardness distributions near weld was similar. the hardness in the HAZ and the fusion zone was higher than that of the base metal and the hardness in the fusion zone was variated with the location. Especially, the hardness of HAZ adjacent to the base metal showed maximum value, and softening zone in the base metal adjacent to HAZ was found. With the increasing of welding current, there were no difference in maximum hardness and average hardness in the fusion zone were, but the hardness of the softening zone reduced. The difference in the hardness in each location of weld due to grain size of prior austenite. The softening of the base metal occurred by tempering of the martensite.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.19.2-19.2
• /
• 2011

The $(Sr_{0.75},\;La_{0.25})TiO_3$ (SLTO) ultra-thin films with various thicknesses have been grown on Ti-O terminated $SrTiO_3$(100) substrate using Laser-Molecular Beam Epitaxy (Laser MBE). By monitoring the in-situ specular spot intensity oscillation of reflection high energy electron diffraction (RHEED), we controlled the layer-by-layer film growth. The film structure and topography were verified by atomic force microscopy (AFM) and high resolution thin film x-ray diffraction by the synchrotron x-ray radiation. We have also investigated the electronic band structure using x-ray absorption spectroscopy (XAS). The ultra thin SLTO film exhibits thickness driven metal-insulator transition around 8 unit cell thickness when the film thickness progressively reduced to 2 unit cell. The SLTO thin films with an insulating character showed band splitting in Ti $L_3-L_2$ edge XAS spectrum which is attributed to Ti 3d band splitting. This narrow d band splitting could drive the metal-insulator transition along with Anderson Localization. In optical conductivity, we have found the spectral weight transfer from coherent part to incoherent part when the film thickness was reduced. This result indicates the possibility of enhanced electron correlation in ultra thin films.

• 한국전자파학회논문지
• /
• 제29권1호
• /
• pp.61-67
• /
• 2018

지하의 비균일성이 지하탐사레이다(GPR) 신호에서 금속관 탐지에 미치는 영향을 수치계산으로 조사하였다. 지하의 비균일성을 모델링하기 위해서 연속적인 랜덤 매질(CRM) 생성기법을 도입하였고, GPR 신호의 전자기 모의계산을 위해 유한차분시간영역(FDTD)법을 구현하였다. 랜덤 비균일 지하에 대한 상대 유전율 분포의 표준편차와 상관길이의 변화에 따라 매설된 금속관의 GPR 신호를 수치 모의계산으로 비교하였다. 지하의 비균일성이 증가함에 따라 지하 클러터의 영향으로 인하여 매설관에 의한 GPR 신호가 심하게 왜곡되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 반도체재료
• /
• pp.38-41
• /
• 2001

In this work, we have been studied the characteristics of each nitride film for the optimization of PMD(pre-metal dielectric) liner nitride process, which can applicable in the recent semiconductor manufacturing process. The deposition conditions of nitride film were splited by PO (protect overcoat) nitride, baseline, low hydrogen, high stress and low hydrogen, respectively. And also we tried to catch hold of correlation between BPSG(boro-phospho silicate glass) deposition and densification. Especially, we used FTIR area method for the analysis of density change of Si-H bonding and Si-NH-Si bonding, which decides the characteristics of nitride film. To judge whether the deposited films were safe or not, we investigated the crack generation of wafer edge after BPSG densification, and the changes of nitride film stress as a function of RF power variation.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.46-54
• /
• 1995

The cold cracking susceptibility of a variety of weld metals deposited by GMAW with several kinds of commercial solid wires for high strength-toughness steel was investigated. G-BOP test and LB-TRC test were carried out to study the effects of preheat, chemical composition and hydrogen level on the weld metal cold cracking. The results obtained are as follows. 1) 10% CPT obtained by G-BOP test was the most valuable criteria for evaluating the cold cracking susceptibility of weld metals compared with percentage of cracking at room temperature and crack free temperature, and it had good correlation with the results of LB-TRC test. 2) Cold cracking susceptibility of weld metals was high in the row of MG100A, MG100C, MG100D and MG100B. Welds deposited with MG130 and MG80 showed similar icidents of cracking with MG100C and MG100B respectively, even though their strength levels were different. 3) Diffusible hydrogen level in weld metals which has good relation with hydrogen content in wire itself was the most critical factor for controlling the cold cracking susceptibility of weld metal.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.454-457
• /
• 1997

The purpose of this study is to develop an optimal model, using existing models, that is able to estimate the amount of spatter utilizing artificial neural network in the short circuit transfer mode of gas metal arc (GMA) welding. The amount of spatter generated during welding can become a barometer which represents the process stability of metal transfer in GMA welding, and it depends on some factors which constitute a periodic waveforms of welding current and arc voltage in short circuit GMA welding. So, the 12 factors, which could express the characteristics for the waveforms, and the amount of spatter are used as input and output variables of the neural network, respectively. Two neural network models to estimate the amount of spatter are proposed: A neural network model, where arc extinction is not considered, and a combined neural network model where it is considered. In order to reduce the calculation time it take to produce an output, the input vector and hidden layers for each model are optimized using the correlation coefficients between each factor and the amount of spattcr. The est~mation performance of each optimized model to the amount of spatter IS assessed and compared to the est~mation performance of the model proposed by Kang. Also, through the evaluation for the estimation performance of each optimized model, it is shown that the combined neural network model can almost perfectly predict the amount of spatter.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제23권1호
• /
• pp.14-24
• /
• 2018

In soil washing, there are many variables including types of reagent and contaminant, washing time, soil-liquid ratio, washing cycles, washing agent concentrations, and etc. To identify the most influencing factors on soil washing process, regression analysis was performed for eight single variables and five combined variables. A quantitative model that employs W/H (molar ratio of washing agent to heavy metal) as a major variable was established based on the regression. The validity of the model was demonstrated by conducting lab experiments with Cu, Pb, Zn, Ni and As-contaminated soils, and various washing reagents including acetic acid, citric acid, malic acid, oxalic acid, ethylenediamine tetraacetic acid (EDTA) and nitriloacetic acid (NTA). The washing efficiencies were compared with the EDTA washing data reported in the literature. The correlation between W/H and removal efficiency was analyzed after dividing data into two groups according to the heavy metal mobility.

• 한국기계가공학회지
• /
• 제17권4호
• /
• pp.160-168
• /
• 2018

Among the components of rotary hooks, a core component of an embroidery sewing system, a study was conducted to apply metal injection molding to the manufacture of a hook body and a housing that was very difficult to mechanical working. The correlation of feedstock, a mixture of binder and SCM 415 metal powder, and properties of the pressure-volume-temperature interrelationship, viscosity, specific heat, and thermal conductivity were measured. Injection molds for the hook body and the housing were developed through injection molding analysis using these properties and conducted injection tests. Optimal injection gate position and number, injection pressure, and injection time were obtained through a comparison of analysis results with the experiment results.