• Journal of Electrochemical Science and Technology
• /
• v.13 no.3
• /
• pp.390-397
• /
• 2022

The use of microwaves as the energy source for synthesis and sintering of ceramics offers substantial advantages compared to conventional gas-fired and electric resistance furnaces. Benefits include much shorter processing times and reaching the sintering temperature more quickly, resulting in superior final product quality. Most oxide ceramics poorly interact with microwave irradiation at low temperatures; thus, a more complex setup including a susceptor is needed, which makes the whole process very complicated. This investigation pursued a new approach, which enabled us to use microwave irradiation directly in poorly coupled oxides. In many solid-state electrochemical devices, the support is either metal or can be reduced to metal. Metal powders in the support can act as an internal susceptor and heat the entire cell. Then sufficient interaction of microwave irradiation and ceramic material can occur as the sample temperature increases. This microwave heating and exothermic reaction of oxidation of the support can sinter the ceramic very efficiently without any external susceptor. In this study, yttria stabilized zirconia (YSZ) and a Ni-YSZ cermet support were used as an example. The cermet was used as the support, and a YSZ electrolyte was coated and sintered directly using microwave irradiation without the use of any susceptor. The results were compared to a similar cell prepared using a conventional electric furnace. The leakage test and full cell power measurement results revealed a fully leak-free electrolyte. Scanning electron microscopy and density measurements show that microwave sintered samples have lower open porosity in the electrode support than conventional heat treatment. This technique offers an efficient way to directly use microwave irradiation to sinter thin film ceramics without a susceptor.

• Journal of Industrial Technology
• /
• v.28 no.A
• /
• pp.195-198
• /
• 2008

Graphite and $MoS_2$ were added respectively to the Cu/Sn bond materials of the same composition as a lubricant in order to find out the effect of lubricants on the mechanical properties and the increase in density of the sintered products for microblades. The addition of $MoS_2$ as a lubricant was more beneficial to strength, fracture toughness, and hardness as well as densification than graphite. $MoS_2$ seemed to be more effective in reducing the friction between the metallic powders and die wall during hot pressing process. Due to the better wettability of MoS2 with bond metal alloy, less amount of interfacial defects which is detrimental to mechanical properties use observed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.138-145
• /
• 1999

Surface hardening of AC4C aluminium alloy with TiC powders was obtained by plasma transferred are (PTA) method, Bead appearance, microstrucutre and wear behavior were characterized in relation to the torch current, powder feed rate and wear condition. The width and the depth of bead were mainly increased with increasing torch current. The comparison of wear behavior between AC4C alloy and PTA treated AC4C alloy showed the remarkable enhancement of wear resistance.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.577-585
• /
• 1992

TiB2 and TiC were prepared from the mixture of metal titanium, boron and graphite powders in Argon atmosphere by Self-propagating High-temperature Synthesis method. The sintered properties of TiB2-TiC composite as a function of TiC content and sintering temperature were investigated in TiB2 matrix. The sintered properties were the most excellent at 10 wt% TiC content in TiB2-TiC composite. The relative density, M.O.R strength, hardness and fracture toughness of TiB2-10 wt% TiC composite sintered at 190$0^{\circ}C$ for 90 min by hot-pressing under the pressure of 30 MPa were 98.6%, 634 MPa, 2128.1 kg/$\textrm{mm}^2$ and 4.09 MN/m3/2, respectively.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.2
• /
• pp.83-91
• /
• 1995

A new method for preparation of thin nickel foam for Ni-MH battery was investigated. In this method, fine graphite powders of $1\mu\textrm{m}$～$2\mu\textrm{m}$ diameter were pasted into pores of thin polyurethane foam film in order to supply electric conducting seeds for nickel deposition by electroless plating reaction. After electroless plating, remaining polyurethane foam was removed chemically by organic solvent treatment and graphite particles also removed by ultrasonic cleaning. Porosity of formed nickel foam was about 85% During electroplating, porosity of the nickel foam decreased less than 5% up to $30\mu\textrm{m}$ coating thickness. And then it was electroplated and heat-treated to improve mechanical strength and ductility. Finally, thin nickel foam for Ni electrode of Ni-MH battery with 80% porosity and $350\mu\textrm{m}$～X$400\mu\textrm{m}$ thickness was obtained.

• Journal of the Korean Ceramic Society
• /
• v.32 no.4
• /
• pp.413-418
• /
• 1995

The (B.Si)C composite was prepared form the mixture of metal boron, silicon, and carbon powders in Ar atmosphere by Self-propagating High-temperature Synthesis Chemical Furnace. The characterization of synthesized power and sintered body were investigated. The microstructure of sintered body suggested that SiC boundary was made between B4C grains. The most excellent mechanical properties, the relative density of 95% oftheoretical value, 3 point flexural strength of 360MPa, and fracture toughness of 3.6MN/m3/2 could be obtained in 80wt% B4C-20 wt% SiC composite were obtained.

• The Korean Journal of Ceramics
• /
• v.2 no.4
• /
• pp.221-225
• /
• 1996

In diamond synthesis by metal film growth method under high pressure and high temperature, the nucleation and growth of diamond was observed dependent on the carbon source variation from graphite powder to the heat treated powders of lamp black carbon. At the low driving force condition near equilibrium pressure and temperature line, nucleation of diamond did not occur but growth of seed diamond appeared in the synthesis from lamp black carbon while both nucleation and growth of diamond took place in the synthesis from graphite. Growth morphology change of diamond occurred from cubo-octahedron to octahedron in the synthesis from graphite but very irregular growth of seed diamond occurred in the synthesis from lamp block carbon. Lamp black carbon transformed to recrystallized graphite first and very nucleation of diamond was observed on the recrystallized graphite surface. Growth morphology of diamond on the recrystallized graphite was clear cubo-octahedron even at higher pressure departure condition from equilibrium pressure and temperature line.

• Journal of the Korean Ceramic Society
• /
• v.27 no.1
• /
• pp.118-126
• /
• 1990

Titanium Cabride powders were prepared by the self-propagating high temperature synthesismethod in air from the mixture of metal titanium powder and carbon powder. The result are as follows : 1. The conversion effciency of higher than 95% can be obtained and the lattice constant value of the product was 4.322$\AA$. 2. The combustion mode, velocity and temperature of combustion wave was photographed using high-speed camera, and showed steady-state, velocity of 15.414mm/sec at 250$0^{\circ}C$. 3. The relative density and MOR strength of TiC sintered at 180$0^{\circ}C$ for 90 minutes by hot-pressing under the pressure of 200kg/$\textrm{cm}^2$ were 95% and 395MPa, respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.8
• /
• pp.34-42
• /
• 2004

A new polishing technique for three dimensional micro/meso-scale parts is suggested using a micro quill and a magnetic chain structure. The principle of this method is to polish the target surface with the collected magnetic brushes at a micro tool by the non-uniform magnetic field generated around the tool. In a typical magnetic abrasive finishing process magnetic particles and abrasive particles are unbonded each other. But, to finish the three dimensional small parts bonded magnetic abrasive have to be used. Bonded magnetic abrasives are made from direct bonding, and their polishing characteristics are also examined. Alumina, silicon carbide and diamond micro powders are used as abrasives. Base metal matrix is carbonyl iron powder. It is found that bonded magnetic abrasives are superior to unbonded one by experiment. finally, the polished surface roughness is evaluated by atomic force microscope.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.17-17
• /
• 2003

선폭법[전기선 폭발 법, Electrical Explosion of wire(EEW)]은 $10^{10A}$$m^2$ 이상의 고밀도 전류를 금속와이어에 인가하여 순간적으로 폭발시키는 기술로서 고밀도 대 전류가 금속와이어를 통과할 때, 저항발열에 의해 와이어가 미세한 입자나 금속증기 형태로 폭발하는 현상을 이용하여 나노분말을 합성하는 방법으로 나노 금속분말 뿐만 아니라 분위기 제어에 의한 산화물, 질화물, 탄화물 및 합금분말 둥 다양한 분말을 제조할 수 있는 장점이 있다. 또한 다른 제조법에 비해 양산화에 가장 근접한 기술로 알려져 있으며, 러시아가 세계적 기술수준으로 가장 앞선 것으로 알려져 있으며, 미국, 독일 및 일본 둥에서 1995년 이후 선폭 기술을 이용하여 나노분말 제조를 산업화하였다.다.