• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2004.04a
• /
• pp.309-316
• /
• 2004

A probabilistic structural integrity assessment is performed for a reactor pressure vessel under PTS(Pressurized Thermal Shock). A semi-elliptical finite axial crack is assumed to he in the beltline region(either base metal or weld meta)1 of the reactor vessel inside surface. The selected random variables are initial crack depth, neutron fluence on the vessel inside surface, copper, nickel, and phosphorus content of the vessel material, and RT/sub NDT/. The probabilities of crack initiation or vessel failure where the crack is propagated through vessel wall are calculated. The probabilities obtained with random crack size are compared to these obtained with deterministic us. Since the failure function cannot to explicitly by selected by selected random variables, Monte Carlo Simulation is applied to perform probabilistic analysis The influence of the amount of neutron fluence is also examined to assess the structural reliability for vessel life time.

• 한국디지털정책학회:학술대회논문집
• /
• 2005.06a
• /
• pp.605-615
• /
• 2005

This paper represent a method of U-Learning based on advanced e-Learning. Ubiquitous computing configuration and advanced Information technology. As we know well, the 21th century is called knowledge based informational society. Many scholar stress that the improved 21th century's educational paradigm be able to success based on advanced educational paradigm. Therefore, we discuss the material for e-Learning fields including with necessity, vision, law, quality authorization etc. Also, we discuss the relational technologies including with meta data, standardization, identification etc. Finally, we propose a method for constructing the U-Learning based on advanced e-Learning and Ubiquitous computing configuration.

• Electrical & Electronic Materials
• /
• v.16 no.9
• /
• pp.61.1-61
• /
• 2003

Stoichiometric, uniform, amorphous ZrO$_2$ films with an equivalent oxide thickness of ∼1.5nm and a dielectric constant of ∼18 were deposited by an atomic layer controlled deposition process on silicon for potential application in meta-oxide-semiconductor(MOS) devices. The conduction mechanism is identified as Schottky emission at low electric fields and as Poole-Frenkel emission at high electric fields. the MOS devices showed low leakage current, small hysteresis(〈50mV), and low interface state density(∼2*10e11/cm2eV). Microdiffraction and high-resolution transmission electron microscopy showed a localized monoclinic phase of ${\alpha}$-ZrO$_2$ and an amorphous interfacial ZrSi$\_$x/O$\_$y/ layer which has a correspondign dielectric constant of 11

• Journal of the Korean Ceramic Society
• /
• v.17 no.4
• /
• pp.213-216
• /
• 1980

A glass-ceramics material of composition %SiO_2$: 38.50, $Al_2O_3$: 26.00, $Na_2O$: 18.00, CaO: 6.00, MgO: 4.00, $TiO_2$: 7.50 was strengthened by coating a series of glazes$(SiO_2-B_2O_3-Al_2O_3-CaO-PbO-Na_2O-)$, which has lower thermal expansion coefficient than that of the glass-ceramics. The thermal expansion coefficient of the glazes ranges $80~90{\times}10^{-7}$cm/cm/$^{\circ}C$, whereas that of the glass-ceramics is $115{\times}10^{-7}$cm/cm/$^{\circ}C$. The glass-ceramics was identified to be composed of nepheline, carnegieite low form, and meta sodium silicate crystal by X-ray diffraction phase analysis. The glaze, having lower melting point and appropriate thermal expansion coefficient, was tried to be stable and good at secondary heat treatment.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.654-659
• /
• 2007

In this paper, the fatigue load spectrum for tilt rotor UAV is developed and fatigue analysis is achieved for flaperon joint. Tilt rotor UAV has two modes which are helicopter mode when UAV is taking off and landing and fixed wing mode when UAV is cruising. To make fatigue load spectrum, FELIX for helicopter mode and TWIST for fixed wing mode are used. And Fatigue analysis of flaperon joint is achieved using fatigue load spectrum we obtained. When S-N test data are analyzed, we use the Kriging meta model to get probability S-N curve for whole range of material life. The result which is life of flaperon joint obtained by suggested fatigue analysis procedure in this paper is compared with that obtained by MSC/Fatigue.

• Transactions of Materials Processing
• /
• v.16 no.6
• /
• pp.438-442
• /
• 2007

Sidewall curl is the curvature that results from non-uniform through-thickness strain present in the sheet stamping process which involves material flow over a die radius. In order to understand and control curl for tight fit-up tolerances, an analytical model that can provide a reliable measure for the amount of curl would be very helpful. In this study, a model is developed based on the moment-curvature relationship during bending-under-tension operations. For the verification of analytical model, sidewall curl is experimentally measured after deformation of a strip using a bending-under-tension test system. The results show a consistent relationship between the theoretically predicted value and the experimentally obtained one, especially in regions of high curl.

• Electrical & Electronic Materials
• /
• v.7 no.2
• /
• pp.94-99
• /
• 1994

The purpose of this work is to investigate the interface characteristics of hydrogenated amorphous silicon thin films prepared by PECVD and photo-induced CVD and to examine the annealing effects of ultraviolet irradiation on hydrogenated amorphous silicon thin films which were degraded by visible light illumination. The interface layer thickness of films deposited by photo-induced CVD was about 600-900.angs. while that by PECVD was about 1000-1300.angs.. These results can show that the quality of interface layer in photo induced CVD film is better than that in PECVD sample. The electrical properties are improved by ultraviolet irradiation on visible light soaked a-Si:H films using photo-CVD light sources, probably due to the fact that UV generates phonons in a-Si:H films and anneal the meta stable defects.

• Journal of the Korean Ceramic Society
• /
• v.14 no.2
• /
• pp.82-87
• /
• 1977

The material used in this experiment is Ha-Dong kaolin whichis composed of almost crystallographically pure meta-halloysite. It was grinded and passed through 250 mesh and 325 mesh. It was treated with oxalic acids and EDTA which are different in concentration. The samples in conical beaker were kept in laboratory incubator at $25^{\circ}C$ for a certain hours. The treated samples were stirred twice a day. The sample in the conditions as A-7 was kept in an autoclave under the pressure of 3 atmospheric. The samples suspended in each solution were kept for 1.5, 3 and 6 months. The transformation of crystals was detected by X-ray spectrometer, electron microscopy, and infrared spectrometer. The sample through 325 mesh compared with one through 250 mesh was transformed much more. It took for 6 months to transfer from halloysite to kaolinite in EDTA, and 3~4 months under 3 atms in autoclave at the same condition. In oxalic acids it took more than 6 months.

• Structural Engineering and Mechanics
• /
• v.58 no.6
• /
• pp.1109-1126
• /
• 2016

The present paper focuses on size optimization of double layer barrel vaults considering nonlinear behavior. In order to tackle the optimization problem an improved colliding bodies optimization (ICBO) algorithm is proposed. The important task that should be achieved before optimization of structural systems is to determine the best form having the least cost. In this study, an attempt is done to find the best form then it is optimized considering linear and non-linear behaviors. In the optimization process based on nonlinear behavior, the geometrical and material nonlinearity effects are included. A large-scale double layer barrel vault is presented as the numerical example of this study and the obtained results indicate that the proposed ICBO has better computational performance compared with other algorithms.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.40-43
• /
• 2000

A process optimal design methodology applicable to steady-state forming with a strain-hardening material is presented. in this approach the optimal design problem is formulated on the basis of a rigid-viscoplastic finite element process model and a derivative based approach is adopted as an optimization technique The process model the schemes for the evaluation of the design sensitivity considering the effect of strain-hardening and an iterative procedure for design optimization are described. the validity of the proposed approach is demonstrated through application to die shape optimal design in extrusion.